Signed-off-by: NBrad Hards <bradh@frogmouth.net>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

The SDIO specification introduces new commands 52 and 53.
Handle as illegal command but do not complain on stderr,
as SDIO-aware OSes (including Linux) may legitimately use
these in their probing for presence of an SDIO card.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Remove a duplicate #include of sysbus.h.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

If pic_irq is greater than 7, the irq level is always 0 on 32bits.
Signed-off-by: NTeLeMan <geleman@gmail.com>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

A few pieces of the pSeries emulation code have variables which are set
but never used, which causes warnings on gcc 4.6.  This patch removes
these instances.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAlexander Graf <agraf@suse.de>

the s390 memory detection has a 16bit field that specifies the amount of
increments. This patch adopts the memory size to always fit into that
scheme. This also fixes virtio detection for these guests, since the
descriptor page is located after the main memory.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

The s390x virtio bus keeps management information on virtio after the top
of the guest's RAM. We need to be able to tell the guest the size of its
RAM (without virtio stuff), but also be able to trap when the guest accesses
RAM outside of its scope (including virtio stuff).

So we need a variable telling us the size of the virtio stuff, so we can
calculate the highest available RAM address from that.

While at it, also increase the maximum number of virtio pages, so we play
along well with more recent kernels that spawn a ridiculous number of virtio
console adapters.
Signed-off-by: NAlexander Graf <agraf@suse.de>

AHCI provides two ways of reading/writing data:

 1) NCQ
 2) ATA commands with the LBA in the command FIS

In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.

This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

This patch makes qemu ignore unplug requests from the guest for pci
devices which are tagged as non-hotpluggable.  Trouble spot is the
piix4 chipset with the ISA bridge.  Requests to unplug that one will
make it go away together with all ISA bus devices, which are not
prepared to be unplugged and thus don't cleanup, leaving active
qemu timers behind in free'ed memory.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

DriveInfo is closely tied to -drive, and like -drive, it mixes
information about host and guest part of the block device.  Unlike
DriveInfo, BlockDriverState should be about the host part only.

One of the remaining guest bits there is the "type hint".  -drive
option media sets it, and qdevs "ide-drive", "scsi-disk" and non-qdev
IF_XEN devices check it to pick HD vs. CD.

Communicate -drive option media via new DriveInfo member media_cd
instead.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

A "scsi-disk" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint.  Unclean; disk vs. CD belongs
to the guest part, not the host part.

Have separate qdevs "scsi-hd" and "scsi-cd" to model disk vs. CD in
the guest part.

Keep scsi-disk for backward compatibility.

Don't copy scsi-disk property removable to scsi-cd.  It's not used and
always zero(!) there.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

An "ide-drive" is either a hard disk or a CD-ROM, depending on the
associated BlockDriverState's type hint.  Unclean; disk vs. CD belongs
to the guest part, not the host part.

Have separate qdevs "ide-hd" and "ide-cd" to model disk vs. CD in
the guest part.

Keep ide-drive for backward compatibility.

"ide-disk" would perhaps be a nicer name than "ide-hd", but there's
already "scsi-disk", which is like "ide-drive", and will be likewise
split in the next commit.  {ide,scsi}-{hd,cd} is the best consistent
set of names I could find within the backward compatibility
straightjacket.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

These printfs aren't really debug messages, but clearly indicate a bug if they
ever become effective. Noone uses DEBUG_IDE, let's re-enable the check
unconditionally and make it an assertion instead of printfs in the device
emulation.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

cppcheck report:
hw/xen_disk.c:309: style:
 Variable 'len' is assigned a value that is never used

Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

Add \n.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>

Fix regression of 667bb59d: ahci_init initializes ahci.mem, so we have to
move bar registration after it.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>

The e500 PCI controller isn't qdev'ified yet. This leads to severe issues
when running with -drive.

To be able to use a virtio disk with an e500 VM, let's convert the PCI
controller over to qdev.
Reviewed-by: NPaul Brook <paul@codesourcery.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Now that we have some nice helpers that can find us a TLB entry, let's
use that on the machine initialization code, so we don't need to know
about the internals of the TLB array.
Signed-off-by: NAlexander Graf <agraf@suse.de>

The MPC8544DS board emulation was only used with KVM so far, so some
parts of the code didn't provide proper values for non-KVM execution.

This patch makes the machine work without KVM enabled. To actually use
this, you also need proper e500v2 MMU emulation.
Signed-off-by: NAlexander Graf <agraf@suse.de>

The MPC8544DS board emulation code ignored the user defined -cpu switch.
This patch enables it to only provide a sane default, not force an e500v2
CPU inside.
Signed-off-by: NAlexander Graf <agraf@suse.de>

The pSeries machine uses two tables to look up guest hcalls for emulation.
One of these is exactly one entry too small to hold all the hcalls it needs
to, leading to memory corruption.

This patch fixes the bug, and while we're at it, make both tables 'static'
since they're never used from other modules.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Read them via KVM_GET_SREGS in kvm_arch_get_registers(),
and display them in "info registers".

Also get CR and PID from the existing KVM_GET_REGS.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Currently the qemu pseries machine numbers its virtual serial devices
from 0.  However, existing pSeries machines running pHyp number them from
0x30000000.

In theory these indices are arbitrary, since everything necessary for the
kernel to find them is advertised in the device tree.  However the debian
installer, at least, incorrectly looks for a device named vty@30... to
determine whether to use the hypervisor console.

Therefore this patch moves the numbers we use to match the existing pHyp
practice, in order to workaround broken userspace apps of this type.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Currently, the qemu emulated pseries machine puts
"qemu,emulated-pSeries-LPAR" in the device tree's root level 'model'
property.  Unfortunately this confuses some installers and ybin, which
expect this to start with "IBM" on pSeries machines.  This patch addresses
this problem, making the property more closely resemble the pattern of
existing real hardware.
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

The original pSeries machine was limited to 32 CPUs, more or less
arbitrarily.  Particularly when we get SMT KVM guests it will be
pretty easy to exceed this.  Therefore, raise the max number of CPUs
in a pseries machine guest to 256.
Signed-off-by: NAnton Blanchard <anton@au1.ibm.com>
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Prototype without "inline" keyword breaks the build with some gcc
versions.  Noticed by Alexander Graf.

Fix this by removing the inline keywork everywhere.  Some functions
can't be inlined anyway as the are referenced using function pointers.
Beside that gcc does a pretty good job on auto-inlining these days.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

The 'sense' field in the HBA status structure is misnamed, as it
actually carries the SCSI status. Rename it.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Cc: qemu-trivial@nongnu.org
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

cppcheck report:
hw/ac97.c:1004: style:
 Variable 'written' is assigned a value that is never used
hw/ac97.c:1072: style:
 Variable 'written' is assigned a value that is never used
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

The code changed here is an unused data type name (evt_flush_occurred).
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NStefan Hajnoczi <stefanha@linux.vnet.ibm.com>

Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Open and bind event channels; map ioreq and buffered ioreq rings.
Signed-off-by: NArun Sharma <arun.sharma@intel.com>
Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAlexander Graf <agraf@suse.de>