irq_target array saving/loading is in the wrong loop.
Version bump.
Signed-off-by: NDmitry Koshelev <karaghiozis@gmail.com>
Acked-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NAndrzej Zaborowski <andrew.zaborowski@intel.com>

The OMAP2430 version of the omap-gpio device has five GPIO modules,
not four like the other OMAP2 versions; wire up the fifth module's
IRQ line correctly.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NAndrzej Zaborowski <andrew.zaborowski@intel.com>

Now the function returned errno, so it is better the new name.
Signed-off-by: NJuan Quintela <quintela@redhat.com>
Reviewed-by: NAnthony Liguori <aliguori@us.ibm.com>

We normally already have an errno value.  When not, abuse EIO.
Signed-off-by: NJuan Quintela <quintela@redhat.com>

QEMUFile * is only intended for migration nowadays.  Using it for
anything else just adds pain and a layer of buffers for no good
reason.
Signed-off-by: NJuan Quintela <quintela@redhat.com>
Reviewed-by: NAnthony Liguori <aliguori@us.ibm.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

The two code paths (for ADDRESS_SPACE_IO and ADDRESS_SPACE_MEM) are
identical.  Unify them.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

This allows to drop various stubs and move the i8359 into hwlib.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

No functional changes.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This key cleanup step requires to move the IRQ debugging bit from
i8259_set_irq directly to the per-PIC pic_set_irq, to pass the PIC
parameters (I/O base, ELCR address and mask, master/slave mode) as
qdev properties, and to interconnect the PICs with their environment via
GPIO pins.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Introduce a reference to the slave PIC for the few cases we need to
access it without a proper pointer at hand and drop PicState2. We could
even live without slave_pic if we had a better way of modeling the
cascade bus the PICs are attached to (in addition to the ISA bus).
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This reflects how real PICs indentify their role (in non-buffered mode):
Pass the state of the /SP input on pic_init and use it instead of
pics_state to differentiate between master and slave mode.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

There is nothing in the i8259 spec that justifies the special
pic_intack_read. At least the Linux PREP kernels configure the PICs
properly so that pic_read_irq returns identical values, and setting
read_reg_select in PIC0 cannot be derived from any special i8259 mode.

So switch ppc_prep to pic_read_irq and drop the now unused PIC code.

CC: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Drop redundant local address variable.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This was probably never used so far: According to the spec, polling
means ack'ing the pending IRQ and setting its corresponding bit in isr.
Moreover, we have to signal a pending IRQ via bit 7 of the returned
value, and we must not return a spurious IRQ if none is pending.

This implements the poll command without the help of pic_poll_read which
is left untouched as pic_intack_read is still using it.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This converts pic_update_irq to work against a single PIC instead of the
complete cascade. Along this change, the required update after
pic_set_irq1 is now moved into that function.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

The ELCR is actually part of the chipset but we model it here for
simplicity reasons. The PIIX3 clears the ELCR on reset, which was once
broken by 4dbe19e1. Fix this by splitting up pic_init_reset from
pic_reset and clearing the register in the latter.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

MIPS and PPC users of the i8259 output signal expect us to report state
updates also after reset. As no consumer (including the master PIC) can
misinterpret the deassert as an activation event, it is safe to simply
update the IRQ state after reset.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

As we want to move the IRQ update to pic_intack, ordering matters: the
slave ack must be executed before the master ack to avoid missing
further pending slave IRQs.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

If pic_poll_read finds no pending IRQ and return a spurious one instead,
no PIC state is changed, thus we do not need to call pic_update_irq.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

As a first step towards more generic master-slave support, remove
parent_irq in favor of a per-PIC output interrupt line. The slave's
line is attached to IRQ2 of the master, but it remains unused for now.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

We are about to call the latter from the former. No functional changes.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>