armv7m_nvic.c

/*
 * ARM Nested Vectored Interrupt Controller
 *
 * Copyright (c) 2006-2007 CodeSourcery.
 * Written by Paul Brook
 *
 * This code is licensed under the GPL.
 *
 * The ARMv7M System controller is fairly tightly tied in with the
 * NVIC.  Much of that is also implemented here.
 */

#include "qemu/osdep.h"
#include "qapi/error.h"
#include "qemu-common.h"
#include "cpu.h"
#include "hw/sysbus.h"
#include "qemu/timer.h"
#include "hw/arm/arm.h"
#include "hw/arm/armv7m_nvic.h"
#include "target/arm/cpu.h"
#include "exec/address-spaces.h"
#include "qemu/log.h"
#include "trace.h"

/* IRQ number counting:
 *
 * the num-irq property counts the number of external IRQ lines
 *
 * NVICState::num_irq counts the total number of exceptions
 * (external IRQs, the 15 internal exceptions including reset,
 * and one for the unused exception number 0).
 *
 * NVIC_MAX_IRQ is the highest permitted number of external IRQ lines.
 *
 * NVIC_MAX_VECTORS is the highest permitted number of exceptions.
 *
 * Iterating through all exceptions should typically be done with
 * for (i = 1; i < s->num_irq; i++) to avoid the unused slot 0.
 *
 * The external qemu_irq lines are the NVIC's external IRQ lines,
 * so line 0 is exception 16.
 *
 * In the terminology of the architecture manual, "interrupts" are
 * a subcategory of exception referring to the external interrupts
 * (which are exception numbers NVIC_FIRST_IRQ and upward).
 * For historical reasons QEMU tends to use "interrupt" and
 * "exception" more or less interchangeably.
 */
#define NVIC_FIRST_IRQ 16
#define NVIC_MAX_IRQ (NVIC_MAX_VECTORS - NVIC_FIRST_IRQ)

/* Effective running priority of the CPU when no exception is active
 * (higher than the highest possible priority value)
 */
#define NVIC_NOEXC_PRIO 0x100

static const uint8_t nvic_id[] = {
    0x00, 0xb0, 0x1b, 0x00, 0x0d, 0xe0, 0x05, 0xb1
};

/* qemu timers run at 1GHz.   We want something closer to 1MHz.  */
#define SYSTICK_SCALE 1000ULL

#define SYSTICK_ENABLE    (1 << 0)
#define SYSTICK_TICKINT   (1 << 1)
#define SYSTICK_CLKSOURCE (1 << 2)
#define SYSTICK_COUNTFLAG (1 << 16)

int system_clock_scale;

/* Conversion factor from qemu timer to SysTick frequencies.  */
static inline int64_t systick_scale(NVICState *s)
{
    if (s->systick.control & SYSTICK_CLKSOURCE)
        return system_clock_scale;
    else
        return 1000;
}

static void systick_reload(NVICState *s, int reset)
{
    /* The Cortex-M3 Devices Generic User Guide says that "When the
     * ENABLE bit is set to 1, the counter loads the RELOAD value from the
     * SYST RVR register and then counts down". So, we need to check the
     * ENABLE bit before reloading the value.
     */
    if ((s->systick.control & SYSTICK_ENABLE) == 0) {
        return;
    }

    if (reset)
        s->systick.tick = qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
    s->systick.tick += (s->systick.reload + 1) * systick_scale(s);
    timer_mod(s->systick.timer, s->systick.tick);
}

static void systick_timer_tick(void * opaque)
{
    NVICState *s = (NVICState *)opaque;
    s->systick.control |= SYSTICK_COUNTFLAG;
    if (s->systick.control & SYSTICK_TICKINT) {
        /* Trigger the interrupt.  */
        armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK);
    }
    if (s->systick.reload == 0) {
        s->systick.control &= ~SYSTICK_ENABLE;
    } else {
        systick_reload(s, 0);
    }
}

static void systick_reset(NVICState *s)
{
    s->systick.control = 0;
    s->systick.reload = 0;
    s->systick.tick = 0;
    timer_del(s->systick.timer);
}

static int nvic_pending_prio(NVICState *s)
{
    /* return the priority of the current pending interrupt,
     * or NVIC_NOEXC_PRIO if no interrupt is pending
     */
    return s->vectpending ? s->vectors[s->vectpending].prio : NVIC_NOEXC_PRIO;
}

/* Return the value of the ISCR RETTOBASE bit:
 * 1 if there is exactly one active exception
 * 0 if there is more than one active exception
 * UNKNOWN if there are no active exceptions (we choose 1,
 * which matches the choice Cortex-M3 is documented as making).
 *
 * NB: some versions of the documentation talk about this
 * counting "active exceptions other than the one shown by IPSR";
 * this is only different in the obscure corner case where guest
 * code has manually deactivated an exception and is about
 * to fail an exception-return integrity check. The definition
 * above is the one from the v8M ARM ARM and is also in line
 * with the behaviour documented for the Cortex-M3.
 */
static bool nvic_rettobase(NVICState *s)
{
    int irq, nhand = 0;

    for (irq = ARMV7M_EXCP_RESET; irq < s->num_irq; irq++) {
        if (s->vectors[irq].active) {
            nhand++;
            if (nhand == 2) {
                return 0;
            }
        }
    }

    return 1;
}

/* Return the value of the ISCR ISRPENDING bit:
 * 1 if an external interrupt is pending
 * 0 if no external interrupt is pending
 */
static bool nvic_isrpending(NVICState *s)
{
    int irq;

    /* We can shortcut if the highest priority pending interrupt
     * happens to be external or if there is nothing pending.
     */
    if (s->vectpending > NVIC_FIRST_IRQ) {
        return true;
    }
    if (s->vectpending == 0) {
        return false;
    }

    for (irq = NVIC_FIRST_IRQ; irq < s->num_irq; irq++) {
        if (s->vectors[irq].pending) {
            return true;
        }
    }
    return false;
}

/* Return a mask word which clears the subpriority bits from
 * a priority value for an M-profile exception, leaving only
 * the group priority.
 */
static inline uint32_t nvic_gprio_mask(NVICState *s)
{
    return ~0U << (s->prigroup + 1);
}

/* Recompute vectpending and exception_prio */
static void nvic_recompute_state(NVICState *s)
{
    int i;
    int pend_prio = NVIC_NOEXC_PRIO;
    int active_prio = NVIC_NOEXC_PRIO;
    int pend_irq = 0;

    for (i = 1; i < s->num_irq; i++) {
        VecInfo *vec = &s->vectors[i];

        if (vec->enabled && vec->pending && vec->prio < pend_prio) {
            pend_prio = vec->prio;
            pend_irq = i;
        }
        if (vec->active && vec->prio < active_prio) {
            active_prio = vec->prio;
        }
    }

    s->vectpending = pend_irq;
    s->exception_prio = active_prio & nvic_gprio_mask(s);

    trace_nvic_recompute_state(s->vectpending, s->exception_prio);
}

/* Return the current execution priority of the CPU
 * (equivalent to the pseudocode ExecutionPriority function).
 * This is a value between -2 (NMI priority) and NVIC_NOEXC_PRIO.
 */
static inline int nvic_exec_prio(NVICState *s)
{
    CPUARMState *env = &s->cpu->env;
    int running;

    if (env->daif & PSTATE_F) { /* FAULTMASK */
        running = -1;
    } else if (env->daif & PSTATE_I) { /* PRIMASK */
        running = 0;
    } else if (env->v7m.basepri > 0) {
        running = env->v7m.basepri & nvic_gprio_mask(s);
    } else {
        running = NVIC_NOEXC_PRIO; /* lower than any possible priority */
    }
    /* consider priority of active handler */
    return MIN(running, s->exception_prio);
}

bool armv7m_nvic_can_take_pending_exception(void *opaque)
{
    NVICState *s = opaque;

    return nvic_exec_prio(s) > nvic_pending_prio(s);
}

/* caller must call nvic_irq_update() after this */
static void set_prio(NVICState *s, unsigned irq, uint8_t prio)
{
    assert(irq > ARMV7M_EXCP_NMI); /* only use for configurable prios */
    assert(irq < s->num_irq);

    s->vectors[irq].prio = prio;

    trace_nvic_set_prio(irq, prio);
}

/* Recompute state and assert irq line accordingly.
 * Must be called after changes to:
 *  vec->active, vec->enabled, vec->pending or vec->prio for any vector
 *  prigroup
 */
static void nvic_irq_update(NVICState *s)
{
    int lvl;
    int pend_prio;

    nvic_recompute_state(s);
    pend_prio = nvic_pending_prio(s);

    /* Raise NVIC output if this IRQ would be taken, except that we
     * ignore the effects of the BASEPRI, FAULTMASK and PRIMASK (which
     * will be checked for in arm_v7m_cpu_exec_interrupt()); changes
     * to those CPU registers don't cause us to recalculate the NVIC
     * pending info.
     */
    lvl = (pend_prio < s->exception_prio);
    trace_nvic_irq_update(s->vectpending, pend_prio, s->exception_prio, lvl);
    qemu_set_irq(s->excpout, lvl);
}

static void armv7m_nvic_clear_pending(void *opaque, int irq)
{
    NVICState *s = (NVICState *)opaque;
    VecInfo *vec;

    assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq);

    vec = &s->vectors[irq];
    trace_nvic_clear_pending(irq, vec->enabled, vec->prio);
    if (vec->pending) {
        vec->pending = 0;
        nvic_irq_update(s);
    }
}

void armv7m_nvic_set_pending(void *opaque, int irq)
{
    NVICState *s = (NVICState *)opaque;
    VecInfo *vec;

    assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq);

    vec = &s->vectors[irq];
    trace_nvic_set_pending(irq, vec->enabled, vec->prio);


    if (irq >= ARMV7M_EXCP_HARD && irq < ARMV7M_EXCP_PENDSV) {
        /* If a synchronous exception is pending then it may be
         * escalated to HardFault if:
         *  * it is equal or lower priority to current execution
         *  * it is disabled
         * (ie we need to take it immediately but we can't do so).
         * Asynchronous exceptions (and interrupts) simply remain pending.
         *
         * For QEMU, we don't have any imprecise (asynchronous) faults,
         * so we can assume that PREFETCH_ABORT and DATA_ABORT are always
         * synchronous.
         * Debug exceptions are awkward because only Debug exceptions
         * resulting from the BKPT instruction should be escalated,
         * but we don't currently implement any Debug exceptions other
         * than those that result from BKPT, so we treat all debug exceptions
         * as needing escalation.
         *
         * This all means we can identify whether to escalate based only on
         * the exception number and don't (yet) need the caller to explicitly
         * tell us whether this exception is synchronous or not.
         */
        int running = nvic_exec_prio(s);
        bool escalate = false;

        if (vec->prio >= running) {
            trace_nvic_escalate_prio(irq, vec->prio, running);
            escalate = true;
        } else if (!vec->enabled) {
            trace_nvic_escalate_disabled(irq);
            escalate = true;
        }

        if (escalate) {
            if (running < 0) {
                /* We want to escalate to HardFault but we can't take a
                 * synchronous HardFault at this point either. This is a
                 * Lockup condition due to a guest bug. We don't model
                 * Lockup, so report via cpu_abort() instead.
                 */
                cpu_abort(&s->cpu->parent_obj,
                          "Lockup: can't escalate %d to HardFault "
                          "(current priority %d)\n", irq, running);
            }

            /* We can do the escalation, so we take HardFault instead */
            irq = ARMV7M_EXCP_HARD;
            vec = &s->vectors[irq];
            s->cpu->env.v7m.hfsr |= R_V7M_HFSR_FORCED_MASK;
        }
    }

    if (!vec->pending) {
        vec->pending = 1;
        nvic_irq_update(s);
    }
}

/* Make pending IRQ active.  */
void armv7m_nvic_acknowledge_irq(void *opaque)
{
    NVICState *s = (NVICState *)opaque;
    CPUARMState *env = &s->cpu->env;
    const int pending = s->vectpending;
    const int running = nvic_exec_prio(s);
    int pendgroupprio;
    VecInfo *vec;

    assert(pending > ARMV7M_EXCP_RESET && pending < s->num_irq);

    vec = &s->vectors[pending];

    assert(vec->enabled);
    assert(vec->pending);

    pendgroupprio = vec->prio & nvic_gprio_mask(s);
    assert(pendgroupprio < running);

    trace_nvic_acknowledge_irq(pending, vec->prio);

    vec->active = 1;
    vec->pending = 0;

    env->v7m.exception = s->vectpending;

    nvic_irq_update(s);
}

int armv7m_nvic_complete_irq(void *opaque, int irq)
{
    NVICState *s = (NVICState *)opaque;
    VecInfo *vec;
    int ret;

    assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq);

    vec = &s->vectors[irq];

    trace_nvic_complete_irq(irq);

    if (!vec->active) {
        /* Tell the caller this was an illegal exception return */
        return -1;
    }

    ret = nvic_rettobase(s);

    vec->active = 0;
    if (vec->level) {
        /* Re-pend the exception if it's still held high; only
         * happens for extenal IRQs
         */
        assert(irq >= NVIC_FIRST_IRQ);
        vec->pending = 1;
    }

    nvic_irq_update(s);

    return ret;
}

/* callback when external interrupt line is changed */
static void set_irq_level(void *opaque, int n, int level)
{
    NVICState *s = opaque;
    VecInfo *vec;

    n += NVIC_FIRST_IRQ;

    assert(n >= NVIC_FIRST_IRQ && n < s->num_irq);

    trace_nvic_set_irq_level(n, level);

    /* The pending status of an external interrupt is
     * latched on rising edge and exception handler return.
     *
     * Pulsing the IRQ will always run the handler
     * once, and the handler will re-run until the
     * level is low when the handler completes.
     */
    vec = &s->vectors[n];
    if (level != vec->level) {
        vec->level = level;
        if (level) {
            armv7m_nvic_set_pending(s, n);
        }
    }
}

static uint32_t nvic_readl(NVICState *s, uint32_t offset)
{
    ARMCPU *cpu = s->cpu;
    uint32_t val;

    switch (offset) {
    case 4: /* Interrupt Control Type.  */
        return ((s->num_irq - NVIC_FIRST_IRQ) / 32) - 1;
    case 0x10: /* SysTick Control and Status.  */
        val = s->systick.control;
        s->systick.control &= ~SYSTICK_COUNTFLAG;
        return val;
    case 0x14: /* SysTick Reload Value.  */
        return s->systick.reload;
    case 0x18: /* SysTick Current Value.  */
        {
            int64_t t;
            if ((s->systick.control & SYSTICK_ENABLE) == 0)
                return 0;
            t = qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
            if (t >= s->systick.tick)
                return 0;
            val = ((s->systick.tick - (t + 1)) / systick_scale(s)) + 1;
            /* The interrupt in triggered when the timer reaches zero.
               However the counter is not reloaded until the next clock
               tick.  This is a hack to return zero during the first tick.  */
            if (val > s->systick.reload)
                val = 0;
            return val;
        }
    case 0x1c: /* SysTick Calibration Value.  */
        return 10000;
    case 0xd00: /* CPUID Base.  */
        return cpu->midr;
    case 0xd04: /* Interrupt Control State.  */
        /* VECTACTIVE */
        val = cpu->env.v7m.exception;
        /* VECTPENDING */
        val |= (s->vectpending & 0xff) << 12;
        /* ISRPENDING - set if any external IRQ is pending */
        if (nvic_isrpending(s)) {
            val |= (1 << 22);
        }
        /* RETTOBASE - set if only one handler is active */
        if (nvic_rettobase(s)) {
            val |= (1 << 11);
        }
        /* PENDSTSET */
        if (s->vectors[ARMV7M_EXCP_SYSTICK].pending) {
            val |= (1 << 26);
        }
        /* PENDSVSET */
        if (s->vectors[ARMV7M_EXCP_PENDSV].pending) {
            val |= (1 << 28);
        }
        /* NMIPENDSET */
        if (s->vectors[ARMV7M_EXCP_NMI].pending) {
            val |= (1 << 31);
        }
        /* ISRPREEMPT not implemented */
        return val;
    case 0xd08: /* Vector Table Offset.  */
        return cpu->env.v7m.vecbase;
    case 0xd0c: /* Application Interrupt/Reset Control.  */
        return 0xfa050000 | (s->prigroup << 8);
    case 0xd10: /* System Control.  */
        /* TODO: Implement SLEEPONEXIT.  */
        return 0;
    case 0xd14: /* Configuration Control.  */
        return cpu->env.v7m.ccr;
    case 0xd24: /* System Handler Status.  */
        val = 0;
        if (s->vectors[ARMV7M_EXCP_MEM].active) {
            val |= (1 << 0);
        }
        if (s->vectors[ARMV7M_EXCP_BUS].active) {
            val |= (1 << 1);
        }
        if (s->vectors[ARMV7M_EXCP_USAGE].active) {
            val |= (1 << 3);
        }
        if (s->vectors[ARMV7M_EXCP_SVC].active) {
            val |= (1 << 7);
        }
        if (s->vectors[ARMV7M_EXCP_DEBUG].active) {
            val |= (1 << 8);
        }
        if (s->vectors[ARMV7M_EXCP_PENDSV].active) {
            val |= (1 << 10);
        }
        if (s->vectors[ARMV7M_EXCP_SYSTICK].active) {
            val |= (1 << 11);
        }
        if (s->vectors[ARMV7M_EXCP_USAGE].pending) {
            val |= (1 << 12);
        }
        if (s->vectors[ARMV7M_EXCP_MEM].pending) {
            val |= (1 << 13);
        }
        if (s->vectors[ARMV7M_EXCP_BUS].pending) {
            val |= (1 << 14);
        }
        if (s->vectors[ARMV7M_EXCP_SVC].pending) {
            val |= (1 << 15);
        }
        if (s->vectors[ARMV7M_EXCP_MEM].enabled) {
            val |= (1 << 16);
        }
        if (s->vectors[ARMV7M_EXCP_BUS].enabled) {
            val |= (1 << 17);
        }
        if (s->vectors[ARMV7M_EXCP_USAGE].enabled) {
            val |= (1 << 18);
        }
        return val;
    case 0xd28: /* Configurable Fault Status.  */
        return cpu->env.v7m.cfsr;
    case 0xd2c: /* Hard Fault Status.  */
        return cpu->env.v7m.hfsr;
    case 0xd30: /* Debug Fault Status.  */
        return cpu->env.v7m.dfsr;
    case 0xd34: /* MMFAR MemManage Fault Address */
        return cpu->env.v7m.mmfar;
    case 0xd38: /* Bus Fault Address.  */
        return cpu->env.v7m.bfar;
    case 0xd3c: /* Aux Fault Status.  */
        /* TODO: Implement fault status registers.  */
        qemu_log_mask(LOG_UNIMP,
                      "Aux Fault status registers unimplemented\n");
        return 0;
    case 0xd40: /* PFR0.  */
        return 0x00000030;
    case 0xd44: /* PRF1.  */
        return 0x00000200;
    case 0xd48: /* DFR0.  */
        return 0x00100000;
    case 0xd4c: /* AFR0.  */
        return 0x00000000;
    case 0xd50: /* MMFR0.  */
        return 0x00000030;
    case 0xd54: /* MMFR1.  */
        return 0x00000000;
    case 0xd58: /* MMFR2.  */
        return 0x00000000;
    case 0xd5c: /* MMFR3.  */
        return 0x00000000;
    case 0xd60: /* ISAR0.  */
        return 0x01141110;
    case 0xd64: /* ISAR1.  */
        return 0x02111000;
    case 0xd68: /* ISAR2.  */
        return 0x21112231;
    case 0xd6c: /* ISAR3.  */
        return 0x01111110;
    case 0xd70: /* ISAR4.  */
        return 0x01310102;
    /* TODO: Implement debug registers.  */
    default:
        qemu_log_mask(LOG_GUEST_ERROR, "NVIC: Bad read offset 0x%x\n", offset);
        return 0;
    }
}

static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value)
{
    ARMCPU *cpu = s->cpu;
    uint32_t oldval;
    switch (offset) {
    case 0x10: /* SysTick Control and Status.  */
        oldval = s->systick.control;
        s->systick.control &= 0xfffffff8;
        s->systick.control |= value & 7;
        if ((oldval ^ value) & SYSTICK_ENABLE) {
            int64_t now = qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
            if (value & SYSTICK_ENABLE) {
                if (s->systick.tick) {
                    s->systick.tick += now;
                    timer_mod(s->systick.timer, s->systick.tick);
                } else {
                    systick_reload(s, 1);
                }
            } else {
                timer_del(s->systick.timer);
                s->systick.tick -= now;
                if (s->systick.tick < 0)
                  s->systick.tick = 0;
            }
        } else if ((oldval ^ value) & SYSTICK_CLKSOURCE) {
            /* This is a hack. Force the timer to be reloaded
               when the reference clock is changed.  */
            systick_reload(s, 1);
        }
        break;
    case 0x14: /* SysTick Reload Value.  */
        s->systick.reload = value;
        break;
    case 0x18: /* SysTick Current Value.  Writes reload the timer.  */
        systick_reload(s, 1);
        s->systick.control &= ~SYSTICK_COUNTFLAG;
        break;
    case 0xd04: /* Interrupt Control State.  */
        if (value & (1 << 31)) {
            armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI);
        }
        if (value & (1 << 28)) {
            armv7m_nvic_set_pending(s, ARMV7M_EXCP_PENDSV);
        } else if (value & (1 << 27)) {
            armv7m_nvic_clear_pending(s, ARMV7M_EXCP_PENDSV);
        }
        if (value & (1 << 26)) {
            armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK);
        } else if (value & (1 << 25)) {
            armv7m_nvic_clear_pending(s, ARMV7M_EXCP_SYSTICK);
        }
        break;
    case 0xd08: /* Vector Table Offset.  */
        cpu->env.v7m.vecbase = value & 0xffffff80;
        break;
    case 0xd0c: /* Application Interrupt/Reset Control.  */
        if ((value >> 16) == 0x05fa) {
            if (value & 4) {
                qemu_irq_pulse(s->sysresetreq);
            }
            if (value & 2) {
                qemu_log_mask(LOG_GUEST_ERROR,
                              "Setting VECTCLRACTIVE when not in DEBUG mode "
                              "is UNPREDICTABLE\n");
            }
            if (value & 1) {
                qemu_log_mask(LOG_GUEST_ERROR,
                              "Setting VECTRESET when not in DEBUG mode "
                              "is UNPREDICTABLE\n");
            }
            s->prigroup = extract32(value, 8, 3);
            nvic_irq_update(s);
        }
        break;
    case 0xd10: /* System Control.  */
        /* TODO: Implement control registers.  */
        qemu_log_mask(LOG_UNIMP, "NVIC: SCR unimplemented\n");
        break;
    case 0xd14: /* Configuration Control.  */
        /* Enforce RAZ/WI on reserved and must-RAZ/WI bits */
        value &= (R_V7M_CCR_STKALIGN_MASK |
                  R_V7M_CCR_BFHFNMIGN_MASK |
                  R_V7M_CCR_DIV_0_TRP_MASK |
                  R_V7M_CCR_UNALIGN_TRP_MASK |
                  R_V7M_CCR_USERSETMPEND_MASK |
                  R_V7M_CCR_NONBASETHRDENA_MASK);

        cpu->env.v7m.ccr = value;
        break;
    case 0xd24: /* System Handler Control.  */
        s->vectors[ARMV7M_EXCP_MEM].active = (value & (1 << 0)) != 0;
        s->vectors[ARMV7M_EXCP_BUS].active = (value & (1 << 1)) != 0;
        s->vectors[ARMV7M_EXCP_USAGE].active = (value & (1 << 3)) != 0;
        s->vectors[ARMV7M_EXCP_SVC].active = (value & (1 << 7)) != 0;
        s->vectors[ARMV7M_EXCP_DEBUG].active = (value & (1 << 8)) != 0;
        s->vectors[ARMV7M_EXCP_PENDSV].active = (value & (1 << 10)) != 0;
        s->vectors[ARMV7M_EXCP_SYSTICK].active = (value & (1 << 11)) != 0;
        s->vectors[ARMV7M_EXCP_USAGE].pending = (value & (1 << 12)) != 0;
        s->vectors[ARMV7M_EXCP_MEM].pending = (value & (1 << 13)) != 0;
        s->vectors[ARMV7M_EXCP_BUS].pending = (value & (1 << 14)) != 0;
        s->vectors[ARMV7M_EXCP_SVC].pending = (value & (1 << 15)) != 0;
        s->vectors[ARMV7M_EXCP_MEM].enabled = (value & (1 << 16)) != 0;
        s->vectors[ARMV7M_EXCP_BUS].enabled = (value & (1 << 17)) != 0;
        s->vectors[ARMV7M_EXCP_USAGE].enabled = (value & (1 << 18)) != 0;
        nvic_irq_update(s);
        break;
    case 0xd28: /* Configurable Fault Status.  */
        cpu->env.v7m.cfsr &= ~value; /* W1C */
        break;
    case 0xd2c: /* Hard Fault Status.  */
        cpu->env.v7m.hfsr &= ~value; /* W1C */
        break;
    case 0xd30: /* Debug Fault Status.  */
        cpu->env.v7m.dfsr &= ~value; /* W1C */
        break;
    case 0xd34: /* Mem Manage Address.  */
        cpu->env.v7m.mmfar = value;
        return;
    case 0xd38: /* Bus Fault Address.  */
        cpu->env.v7m.bfar = value;
        return;
    case 0xd3c: /* Aux Fault Status.  */
        qemu_log_mask(LOG_UNIMP,
                      "NVIC: Aux fault status registers unimplemented\n");
        break;
    case 0xf00: /* Software Triggered Interrupt Register */
    {
        /* user mode can only write to STIR if CCR.USERSETMPEND permits it */
        int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ;
        if (excnum < s->num_irq &&
            (arm_current_el(&cpu->env) ||
             (cpu->env.v7m.ccr & R_V7M_CCR_USERSETMPEND_MASK))) {
            armv7m_nvic_set_pending(s, excnum);
        }
        break;
    }
    default:
        qemu_log_mask(LOG_GUEST_ERROR,
                      "NVIC: Bad write offset 0x%x\n", offset);
    }
}

static uint64_t nvic_sysreg_read(void *opaque, hwaddr addr,
                                 unsigned size)
{
    NVICState *s = (NVICState *)opaque;
    uint32_t offset = addr;
    unsigned i, startvec, end;
    uint32_t val;

    switch (offset) {
    /* reads of set and clear both return the status */
    case 0x100 ... 0x13f: /* NVIC Set enable */
        offset += 0x80;
        /* fall through */
    case 0x180 ... 0x1bf: /* NVIC Clear enable */
        val = 0;
        startvec = offset - 0x180 + NVIC_FIRST_IRQ; /* vector # */

        for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) {
            if (s->vectors[startvec + i].enabled) {
                val |= (1 << i);
            }
        }
        break;
    case 0x200 ... 0x23f: /* NVIC Set pend */
        offset += 0x80;
        /* fall through */
    case 0x280 ... 0x2bf: /* NVIC Clear pend */
        val = 0;
        startvec = offset - 0x280 + NVIC_FIRST_IRQ; /* vector # */
        for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) {
            if (s->vectors[startvec + i].pending) {
                val |= (1 << i);
            }
        }
        break;
    case 0x300 ... 0x33f: /* NVIC Active */
        val = 0;
        startvec = offset - 0x300 + NVIC_FIRST_IRQ; /* vector # */

        for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) {
            if (s->vectors[startvec + i].active) {
                val |= (1 << i);
            }
        }
        break;
    case 0x400 ... 0x5ef: /* NVIC Priority */
        val = 0;
        startvec = offset - 0x400 + NVIC_FIRST_IRQ; /* vector # */

        for (i = 0; i < size && startvec + i < s->num_irq; i++) {
            val |= s->vectors[startvec + i].prio << (8 * i);
        }
        break;
    case 0xd18 ... 0xd23: /* System Handler Priority.  */
        val = 0;
        for (i = 0; i < size; i++) {
            val |= s->vectors[(offset - 0xd14) + i].prio << (i * 8);
        }
        break;
    case 0xfe0 ... 0xfff: /* ID.  */
        if (offset & 3) {
            val = 0;
        } else {
            val = nvic_id[(offset - 0xfe0) >> 2];
        }
        break;
    default:
        if (size == 4) {
            val = nvic_readl(s, offset);
        } else {
            qemu_log_mask(LOG_GUEST_ERROR,
                          "NVIC: Bad read of size %d at offset 0x%x\n",
                          size, offset);
            val = 0;
        }
    }

    trace_nvic_sysreg_read(addr, val, size);
    return val;
}

static void nvic_sysreg_write(void *opaque, hwaddr addr,
                              uint64_t value, unsigned size)
{
    NVICState *s = (NVICState *)opaque;
    uint32_t offset = addr;
    unsigned i, startvec, end;
    unsigned setval = 0;

    trace_nvic_sysreg_write(addr, value, size);

    switch (offset) {
    case 0x100 ... 0x13f: /* NVIC Set enable */
        offset += 0x80;
        setval = 1;
        /* fall through */
    case 0x180 ... 0x1bf: /* NVIC Clear enable */
        startvec = 8 * (offset - 0x180) + NVIC_FIRST_IRQ;

        for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) {
            if (value & (1 << i)) {
                s->vectors[startvec + i].enabled = setval;
            }
        }
        nvic_irq_update(s);
        return;
    case 0x200 ... 0x23f: /* NVIC Set pend */
        /* the special logic in armv7m_nvic_set_pending()
         * is not needed since IRQs are never escalated
         */
        offset += 0x80;
        setval = 1;
        /* fall through */
    case 0x280 ... 0x2bf: /* NVIC Clear pend */
        startvec = 8 * (offset - 0x280) + NVIC_FIRST_IRQ; /* vector # */

        for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) {
            if (value & (1 << i)) {
                s->vectors[startvec + i].pending = setval;
            }
        }
        nvic_irq_update(s);
        return;
    case 0x300 ... 0x33f: /* NVIC Active */
        return; /* R/O */
    case 0x400 ... 0x5ef: /* NVIC Priority */
        startvec = 8 * (offset - 0x400) + NVIC_FIRST_IRQ; /* vector # */

        for (i = 0; i < size && startvec + i < s->num_irq; i++) {
            set_prio(s, startvec + i, (value >> (i * 8)) & 0xff);
        }
        nvic_irq_update(s);
        return;
    case 0xd18 ... 0xd23: /* System Handler Priority.  */
        for (i = 0; i < size; i++) {
            unsigned hdlidx = (offset - 0xd14) + i;
            set_prio(s, hdlidx, (value >> (i * 8)) & 0xff);
        }
        nvic_irq_update(s);
        return;
    }
    if (size == 4) {
        nvic_writel(s, offset, value);
        return;
    }
    qemu_log_mask(LOG_GUEST_ERROR,
                  "NVIC: Bad write of size %d at offset 0x%x\n", size, offset);
}

static const MemoryRegionOps nvic_sysreg_ops = {
    .read = nvic_sysreg_read,
    .write = nvic_sysreg_write,
    .endianness = DEVICE_NATIVE_ENDIAN,
};

static int nvic_post_load(void *opaque, int version_id)
{
    NVICState *s = opaque;
    unsigned i;

    /* Check for out of range priority settings */
    if (s->vectors[ARMV7M_EXCP_RESET].prio != -3 ||
        s->vectors[ARMV7M_EXCP_NMI].prio != -2 ||
        s->vectors[ARMV7M_EXCP_HARD].prio != -1) {
        return 1;
    }
    for (i = ARMV7M_EXCP_MEM; i < s->num_irq; i++) {
        if (s->vectors[i].prio & ~0xff) {
            return 1;
        }
    }

    nvic_recompute_state(s);

    return 0;
}

static const VMStateDescription vmstate_VecInfo = {
    .name = "armv7m_nvic_info",
    .version_id = 1,
    .minimum_version_id = 1,
    .fields = (VMStateField[]) {
        VMSTATE_INT16(prio, VecInfo),
        VMSTATE_UINT8(enabled, VecInfo),
        VMSTATE_UINT8(pending, VecInfo),
        VMSTATE_UINT8(active, VecInfo),
        VMSTATE_UINT8(level, VecInfo),
        VMSTATE_END_OF_LIST()
    }
};

static const VMStateDescription vmstate_nvic = {
    .name = "armv7m_nvic",
    .version_id = 3,
    .minimum_version_id = 3,
    .post_load = &nvic_post_load,
    .fields = (VMStateField[]) {
        VMSTATE_STRUCT_ARRAY(vectors, NVICState, NVIC_MAX_VECTORS, 1,
                             vmstate_VecInfo, VecInfo),
        VMSTATE_UINT32(systick.control, NVICState),
        VMSTATE_UINT32(systick.reload, NVICState),
        VMSTATE_INT64(systick.tick, NVICState),
        VMSTATE_TIMER_PTR(systick.timer, NVICState),
        VMSTATE_UINT32(prigroup, NVICState),
        VMSTATE_END_OF_LIST()
    }
};

static Property props_nvic[] = {
    /* Number of external IRQ lines (so excluding the 16 internal exceptions) */
    DEFINE_PROP_UINT32("num-irq", NVICState, num_irq, 64),
    DEFINE_PROP_END_OF_LIST()
};

static void armv7m_nvic_reset(DeviceState *dev)
{
    NVICState *s = NVIC(dev);

    s->vectors[ARMV7M_EXCP_NMI].enabled = 1;
    s->vectors[ARMV7M_EXCP_HARD].enabled = 1;
    /* MEM, BUS, and USAGE are enabled through
     * the System Handler Control register
     */
    s->vectors[ARMV7M_EXCP_SVC].enabled = 1;
    s->vectors[ARMV7M_EXCP_DEBUG].enabled = 1;
    s->vectors[ARMV7M_EXCP_PENDSV].enabled = 1;
    s->vectors[ARMV7M_EXCP_SYSTICK].enabled = 1;

    s->vectors[ARMV7M_EXCP_RESET].prio = -3;
    s->vectors[ARMV7M_EXCP_NMI].prio = -2;
    s->vectors[ARMV7M_EXCP_HARD].prio = -1;

    /* Strictly speaking the reset handler should be enabled.
     * However, we don't simulate soft resets through the NVIC,
     * and the reset vector should never be pended.
     * So we leave it disabled to catch logic errors.
     */

    s->exception_prio = NVIC_NOEXC_PRIO;
    s->vectpending = 0;

    systick_reset(s);
}

static void armv7m_nvic_realize(DeviceState *dev, Error **errp)
{
    NVICState *s = NVIC(dev);

    s->cpu = ARM_CPU(qemu_get_cpu(0));
    assert(s->cpu);

    if (s->num_irq > NVIC_MAX_IRQ) {
        error_setg(errp, "num-irq %d exceeds NVIC maximum", s->num_irq);
        return;
    }

    qdev_init_gpio_in(dev, set_irq_level, s->num_irq);

    /* include space for internal exception vectors */
    s->num_irq += NVIC_FIRST_IRQ;

    /* The NVIC and System Control Space (SCS) starts at 0xe000e000
     * and looks like this:
     *  0x004 - ICTR
     *  0x010 - 0x1c - systick
     *  0x100..0x7ec - NVIC
     *  0x7f0..0xcff - Reserved
     *  0xd00..0xd3c - SCS registers
     *  0xd40..0xeff - Reserved or Not implemented
     *  0xf00 - STIR
     *
     * At the moment there is only one thing in the container region,
     * but we leave it in place to allow us to pull systick out into
     * its own device object later.
     */
    memory_region_init(&s->container, OBJECT(s), "nvic", 0x1000);
    /* The system register region goes at the bottom of the priority
     * stack as it covers the whole page.
     */
    memory_region_init_io(&s->sysregmem, OBJECT(s), &nvic_sysreg_ops, s,
                          "nvic_sysregs", 0x1000);
    memory_region_add_subregion(&s->container, 0, &s->sysregmem);

    /* Map the whole thing into system memory at the location required
     * by the v7M architecture.
     */
    memory_region_add_subregion(get_system_memory(), 0xe000e000, &s->container);
    s->systick.timer = timer_new_ns(QEMU_CLOCK_VIRTUAL, systick_timer_tick, s);
}

static void armv7m_nvic_instance_init(Object *obj)
{
    /* We have a different default value for the num-irq property
     * than our superclass. This function runs after qdev init
     * has set the defaults from the Property array and before
     * any user-specified property setting, so just modify the
     * value in the GICState struct.
     */
    DeviceState *dev = DEVICE(obj);
    NVICState *nvic = NVIC(obj);
    SysBusDevice *sbd = SYS_BUS_DEVICE(obj);

    sysbus_init_irq(sbd, &nvic->excpout);
    qdev_init_gpio_out_named(dev, &nvic->sysresetreq, "SYSRESETREQ", 1);
}

static void armv7m_nvic_class_init(ObjectClass *klass, void *data)
{
    DeviceClass *dc = DEVICE_CLASS(klass);

    dc->vmsd  = &vmstate_nvic;
    dc->props = props_nvic;
    dc->reset = armv7m_nvic_reset;
    dc->realize = armv7m_nvic_realize;
}

static const TypeInfo armv7m_nvic_info = {
    .name          = TYPE_NVIC,
    .parent        = TYPE_SYS_BUS_DEVICE,
    .instance_init = armv7m_nvic_instance_init,
    .instance_size = sizeof(NVICState),
    .class_init    = armv7m_nvic_class_init,
    .class_size    = sizeof(SysBusDeviceClass),
};

static void armv7m_nvic_register_types(void)
{
    type_register_static(&armv7m_nvic_info);
}

type_init(armv7m_nvic_register_types)