Add an evaluation board device tree more in-line with all our other
device trees.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Support the V1.1 hardware revisions with the following change:

Changed power rail for MMC1 interface to a 3.3V/1.8V switchable rail in
order to be able to run UHS SD cards in ultra high speed 1.8V mode.

[  207.502011] mmc2: host does not support reading read-only switch,
 assuming write-enable
[  207.517011] mmc2: new ultra high speed SDR104 SDHC card at address
 aaaa
[  207.534190] mmcblk2: mmc2:aaaa SE32G 29.7 GiB
[  207.545096]  mmcblk2: p1

root@apalis-t30:~# cat /sys/kernel/debug/mmc2/ios
clock:          208000000 Hz
actual clock:   204000000 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      2 (4 bits)
timing spec:    6 (sd uhs SDR104)
signal voltage: 1 (1.80 V)
driver type:    0 (driver type B)
root@apalis-t30:~# hdparm -t /dev/mmcblk2

/dev/mmcblk2:
 Timing buffered disk reads: 256 MB in  3.02 seconds =  84.71 MB/sec
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This adds a base device tree file for the RZN1-DB board, with only the
basic support allowing the system to boot to a prompt. Only one UART is
used, with only a single CPU running.
Signed-off-by: NMichel Pollet <michel.pollet@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add support for the Zodiac Inflight Innovations CFU1
board (VF610-based).

Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This adds support for Lairds upcoming SOM module, featuring Marvell WiFi
and Bluetooth, 2Gb NAND / 1Gb LPDDR SDRAM, and an Atmel SAMA5D3 CPU.
Signed-off-by: NBen Whitten <ben.whitten@lairdtech.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>

Add support for the LoRa gateway from Laird, the RG1xx.
This board houses the WB50NBT CPU module along with a Semtech SX1301 based
concentrator card.
https://www.lairdtech.com/products/rg1xx-lora-gatewaySigned-off-by: NBen Whitten <ben.whitten@lairdtech.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>

This adds support for Lairds CPU module, featuring Atheros wifi, CSR
Bluetooth and, Atmel SAMA5D3 CPU.
https://www.lairdtech.com/products/wb50nbt-wi-fi-bluetooth-moduleSigned-off-by: NBen Whitten <ben.whitten@lairdtech.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>

This adds support for Lairds combo CPU module, featuring on board
Atheros wifi, CSR Bluetooth radio and, Atmel CPU.
https://www.lairdtech.com/products/wb45nbtSigned-off-by: NBen Whitten <ben.whitten@lairdtech.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>

Add a dts for MYIR Z-turn board and respective target in Makefile.
Signed-off-by: NAnton Gerasimov <tossel@gmail.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add support for Zodiac Inflight Innovations SSMB SPU3
board (VF610-based).

Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: NChris Healy <cphealy@gmail.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:

 * Gigabit capable PHY
 * Extra USB hub, optional i2c control
 * lps3331ap barometer connected over i2c
 * MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
 * 1GiB DDR3 RAM
 * RTL8723 Wifi/Bluetooth connected over USB

Tested on a revision G board.
Signed-off-by: NKoen Kooi <koen@dominion.thruhere.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OSD3358-SM-RED is a dev board for OSD335x System-in-Package(SiP) devices from
Octavo Systems.

This board family can be indentified by the A335BNLTOS00 in the at24 eeprom:
A2: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 4f 53 30 30 |.U3.A335BNLTOS00|]

https://octavosystems.com/octavo_products/osd3358-sm-red/Signed-off-by: NNeeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.

Its hardware specifications are:

* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: NAlex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Normally, we didn't release this kind of baord to user. This specific
board exists only in the early stage of development inside MediaTek -
and that may confuse peoples.

Hence this patch removes related files accordingly.

Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Acked-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

The Storlink Gemini324 EV-Board also known as Storm
Semiconductor SL93512R_BRD is ground zero for the Gemini
devices. We add a device tree so we can support it, it
turns out to be pretty trivial.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add support for the Zodiac Inflight Innovations i.MX51-base SCU3 Ethernet
Switch Board (ESB)

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NAndrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for the Zodiac Inflight Innovations SCU2 Mezz
board (i.MX51-based).

Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NAndrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: NChris Healy <cphealy@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The added DTS contains a combined description of LogicPD MX31 Lite
SoM devices, peripherals are routed to ports on a baseboard:
* PATA controller,
* SD/MMC controller,
* 2 GPIO LEDs,
* UART controllers,
* Freescale MC13783 MFD connected over SPI,
* SMSC LAN9117,
* ST Micro NAND SLC, 64 MiB,
* Intel NOR flash, 16 MiB.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Colibri-T20 can come in 256 MB RAM (with 512 MB NAND) or 512 MB RAM
(with 1024 MB NAND) flavors.  Both of them will use the same DTSI
expecting the bootloader to do the fixup of /memory node.  However in
case it does not happen, let's stay on safe side by limiting the memory
to 256 MB for both versions of Colibri-T20.

Rename to remove the unnecessary memory size from the device tree file
name.  While at it, also follow the typical Toradex SoC, module, carrier
board hierarchy.
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: NStefan Agner <stefan@agner.ch>
Tested-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g.  It belongs to Samsung
Aries devices family.
Initial version have support for:
 - sdcard
 - max8998 pmic and rtc
 - max17040 fuel gauge
 - gpio keys
 - fimd (no panel driver yet)
 - usb (peripherial mode)
 - wifi
Signed-off-by: NJonathan Bakker <xc-racer2@live.ca>
Signed-off-by: NPaweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

This DTS file have initial support Samsung Galaxy S phone, also known as
i9000.  It belongs to Samsung Aries devices family.
Initial version have support for:
 - sdcard
 - internal memory
 - max8998 pmic and rtc
 - max17040 fuel gauge
 - gpio keys
 - fimd (no panel driver yet)
 - usb (peripherial mode)
 - wifi
Signed-off-by: NPaweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

The helios4 is a Armada388 based nas board designed by SolidRun and
based on their SOM. It is sold by kobol.io the dts file came from
https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch
I added a SPDX license line to match the clearfog it says it was based
on and a compatible line for "kobol,helios4"
Signed-off-by: NDennis Gilmore <dennis@ausil.us>
Signed-off-by: NGregory CLEMENT <gregory.clement@bootlin.com>

The Raspberry Pi Compute Module (CM1) is a SoM which contains a
BCM2835 processor, 512 MB RAM and a 4 GB eMMC. There is also a carrier
board which is called Compute Module IO Board.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NEric Anholt <eric@anholt.net>

i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.

notable features:
CPU                 NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory              Up to 2 GB DDR3-1066
Video Interfaces    Up to 1 Parallel Up to 2 LVDS HDMI 1.4
                    port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add dts file support for imx6sll EVK board.
Signed-off-by: NBai Ping <ping.bai@nxp.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Acked-by: NDong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Reviewed-by: NAbhishek Sahu <absahu@codeaurora.org>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NSricharan R <sricharan@codeaurora.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Reviewed-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NSricharan R <sricharan@codeaurora.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Reviewed-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NSricharan R <sricharan@codeaurora.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

Reviewed-by: NAbhishek Sahu <absahu@codeaurora.org>
Tested-by: NVaradarajan Narayanan <varada@codeaurora.org>
Signed-off-by: NSricharan R <sricharan@codeaurora.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

This patch adds a DTS file for Sony Xperia Z1 Compact with support for
regulators, serial UART, eMMC/SD-card, USB, charger, backlight,
coincell and buttons.

Work based on arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts.
Signed-off-by: NAttila Szöllősi <ata2001@airmail.cc>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

S2600WF is a Intel platform family with an ASPEED AST2500 BMC.
Signed-off-by: NJames Feist <james.feist@linux.intel.com>
Signed-off-by: NJoel Stanley <joel@jms.id.au>

The Inventec Lanyang is Power 9 platform with ast2500 BMC.
Signed-off-by: NBrian Yang <yang.brianc.w@inventec.com>
Acked-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NJoel Stanley <joel@jms.id.au>

Initial introduction of Portwell Neptune family equipped with
Aspeed 2500 BMC SoC. Neptune is a x86 server development kit with a
ASPEED ast2500 BMC manufactured by Portwell. Specifically, This
adds the neptune platform device tree file including the flash
layout used by the neptune machines.
Signed-off-by: NAmithash Prasad <amithash@fb.com>
Acked-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NJoel Stanley <joel@jms.id.au>

Valve Steam Link is a consumer device built around the Marvell BG2CD SoC.
This board file enables the UART, USB and Ethernet interfaces as well as
internal I2C and SDIO, and adds SoC voltage regulator and board-specific
GPIO restart method info.

Cc: Sam Lantinga <saml@valvesoftware.com>
Signed-off-by: NAlexander Monakov <amonakov@ispras.ru>
Signed-off-by: NJisheng Zhang <Jisheng.Zhang@synaptics.com>

Currently there are two identical Kconfig options where only differences
are the Kconfig help text and the list of .dtbs that are built:
- MACH_MESON8
- MACH_MESON8B

Build the Meson8b .dtbs when MACH_MESON8 is selected to get rid of the
latter Kconfig symbol later.
Suggested-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>

With the new rev.E of A20-SOM-EVB, there is option for 16GB eMMC.
Currently used card is KLMAG2GEND, wired to MMC2 slot.
Signed-off-by: NStefan Mavrodiev <stefan@olimex.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add MT7623N reference board with eMMC. On the board, there is additional
external PHY ICPlus IP1001 transceiver available by port 5 on the MDIO
bus connectted with GMAC2.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Suggested-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

Add MT7623A reference board with eMMC and NAND, respectively.

The both boards compared against MT7623N BPI-R2, we could see there are
UART[0-1] and USB2 being removed, I2C2 and SPI1 being added, I2C1, UART2
owning distinct pin usage and an extra WM8960 codec chip plugged into the
I2C1 offering the functionality of audio player and recorder through
SoC audio front-end engine (AFE).
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Suggested-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

The Tronsmart MXIII Plus is an Android TV box which uses the Amlogic
S812 (Meson8m2) SoC. It uses a Realtek RTL8211F RGMII Ethernet PHY as
well as a Ricoh RN5T618 system power controller. It also comes with an
Ampak AP6330 SDIO wifi/Bluetooth combo chip (support for wifi and
Bluetooth is currently not added because the Linux drivers currently
only support one MMC controller and that is used for the SD card).
Signed-off-by: NOleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>