ARM: dts: add Raspberry Pi Compute Module and IO board

The Raspberry Pi Compute Module (CM1) is a SoM which contains a
BCM2835 processor, 512 MB RAM and a 4 GB eMMC. There is also a carrier
board which is called Compute Module IO Board.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
Reviewed-by: NEric Anholt <eric@anholt.net>

arch/arm/boot/dts/Makefile

@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-b-rev2.dtb \
 	bcm2835-rpi-b-plus.dtb \
 	bcm2835-rpi-a-plus.dtb \
+	bcm2835-rpi-cm1-io1.dtb \
 	bcm2836-rpi-2-b.dtb \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "HDMI_HPD_N",
+			  /* Also used as ACT LED */
+			  "EMMC_EN_N",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi

+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	leds {
+		act {
+			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&sdhost {
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+};