Consider a normal (L1) guest running under the main hypervisor (L0),
and then a nested guest (L2) running under the L1 guest which is acting
as a nested hypervisor. L0 has page tables to map the address space for
L1 providing the translation from L1 real address -> L0 real address;

	L1
	|
	| (L1 -> L0)
	|
	----> L0

There are also page tables in L1 used to map the address space for L2
providing the translation from L2 real address -> L1 read address. Since
the hardware can only walk a single level of page table, we need to
maintain in L0 a "shadow_pgtable" for L2 which provides the translation
from L2 real address -> L0 real address. Which looks like;

	L2				L2
	|				|
	| (L2 -> L1)			|
	|				|
	----> L1			| (L2 -> L0)
	      |				|
	      | (L1 -> L0)		|
	      |				|
	      ----> L0			--------> L0

When a page fault occurs while running a nested (L2) guest we need to
insert a pte into this "shadow_pgtable" for the L2 -> L0 mapping. To
do this we need to:

1. Walk the pgtable in L1 memory to find the L2 -> L1 mapping, and
   provide a page fault to L1 if this mapping doesn't exist.
2. Use our L1 -> L0 pgtable to convert this L1 address to an L0 address,
   or try to insert a pte for that mapping if it doesn't exist.
3. Now we have a L2 -> L0 mapping, insert this into our shadow_pgtable

Once this mapping exists we can take rc faults when hardware is unable
to automatically set the reference and change bits in the pte. On these
we need to:

1. Check the rc bits on the L2 -> L1 pte match, and otherwise reflect
   the fault down to L1.
2. Set the rc bits in the L1 -> L0 pte which corresponds to the same
   host page.
3. Set the rc bits in the L2 -> L0 pte.

As we reuse a large number of functions in book3s_64_mmu_radix.c for
this we also needed to refactor a number of these functions to take
an lpid parameter so that the correct lpid is used for tlb invalidations.
The functionality however has remained the same.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds a new hypercall, H_ENTER_NESTED, which is used by a nested
hypervisor to enter one of its nested guests.  The hypercall supplies
register values in two structs.  Those values are copied by the level 0
(L0) hypervisor (the one which is running in hypervisor mode) into the
vcpu struct of the L1 guest, and then the guest is run until an
interrupt or error occurs which needs to be reported to L1 via the
hypercall return value.

Currently this assumes that the L0 and L1 hypervisors are the same
endianness, and the structs passed as arguments are in native
endianness.  If they are of different endianness, the version number
check will fail and the hcall will be rejected.

Nested hypervisors do not support indep_threads_mode=N, so this adds
code to print a warning message if the administrator has set
indep_threads_mode=N, and treat it as Y.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This starts the process of adding the code to support nested HV-style
virtualization.  It defines a new H_SET_PARTITION_TABLE hypercall which
a nested hypervisor can use to set the base address and size of a
partition table in its memory (analogous to the PTCR register).
On the host (level 0 hypervisor) side, the H_SET_PARTITION_TABLE
hypercall from the guest is handled by code that saves the virtual
PTCR value for the guest.

This also adds code for creating and destroying nested guests and for
reading the partition table entry for a nested guest from L1 memory.
Each nested guest has its own shadow LPID value, different in general
from the LPID value used by the nested hypervisor to refer to it.  The
shadow LPID value is allocated at nested guest creation time.

Nested hypervisor functionality is only available for a radix guest,
which therefore means a radix host on a POWER9 (or later) processor.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

kvmppc_mmu_radix_xlate() is used to translate an effective address
through the process tables. The process table and partition tables have
identical layout. Exploit this fact to make the kvmppc_mmu_radix_xlate()
function able to translate either an effective address through the
process tables or a guest real address through the partition tables.

[paulus@ozlabs.org - reduced diffs from previous code]
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When the 'regs' field was added to struct kvm_vcpu_arch, the code
was changed to use several of the fields inside regs (e.g., gpr, lr,
etc.) but not the ccr field, because the ccr field in struct pt_regs
is 64 bits on 64-bit platforms, but the cr field in kvm_vcpu_arch is
only 32 bits.  This changes the code to use the regs.ccr field
instead of cr, and changes the assembly code on 64-bit platforms to
use 64-bit loads and stores instead of 32-bit ones.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It is not currently possible to create the full number of possible
VCPUs (KVM_MAX_VCPUS) on Power9 with KVM-HV when the guest uses fewer
threads per core than its core stride (or "VSMT mode"). This is
because the VCORE ID and XIVE offsets grow beyond KVM_MAX_VCPUS
even though the VCPU ID is less than KVM_MAX_VCPU_ID.

To address this, "pack" the VCORE ID and XIVE offsets by using
knowledge of the way the VCPU IDs will be used when there are fewer
guest threads per core than the core stride. The primary thread of
each core will always be used first. Then, if the guest uses more than
one thread per core, these secondary threads will sequentially follow
the primary in each core.

So, the only way an ID above KVM_MAX_VCPUS can be seen, is if the
VCPUs are being spaced apart, so at least half of each core is empty,
and IDs between KVM_MAX_VCPUS and (KVM_MAX_VCPUS * 2) can be mapped
into the second half of each core (4..7, in an 8-thread core).

Similarly, if IDs above KVM_MAX_VCPUS * 2 are seen, at least 3/4 of
each core is being left empty, and we can map down into the second and
third quarters of each core (2, 3 and 5, 6 in an 8-thread core).

Lastly, if IDs above KVM_MAX_VCPUS * 4 are seen, only the primary
threads are being used and 7/8 of the core is empty, allowing use of
the 1, 5, 3 and 7 thread slots.

(Strides less than 8 are handled similarly.)

This allows the VCORE ID or offset to be calculated quickly from the
VCPU ID or XIVE server numbers, without access to the VCPU structure.

[paulus@ozlabs.org - tidied up comment a little, changed some WARN_ONCE
 to pr_devel, wrapped line, fixed id check.]
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Currently guest kernel doesn't handle TAR facility unavailable and it
always runs with TAR bit on. PR KVM will lazily enable TAR. TAR is not
a frequent-use register and it is not included in SVCPU struct.

Due to the above, the checkpointed TAR val might be a bogus TAR val.
To solve this issue, we will make vcpu->arch.fscr tar bit consistent
with shadow_fscr when TM is enabled.

At the end of emulating treclaim., the correct TAR val need to be loaded
into the register if FSCR_TAR bit is on.

At the beginning of emulating trechkpt., TAR needs to be flushed so that
the right tar val can be copied into tar_tm.

Tested with:
tools/testing/selftests/powerpc/tm/tm-tar
tools/testing/selftests/powerpc/ptrace/ptrace-tm-tar (remove DSCR/PPR
related testing).
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This patch adds host emulation when guest PR KVM executes "trechkpt.",
which is a privileged instruction and will trap into host.

We firstly copy vcpu ongoing content into vcpu tm checkpoint
content, then perform kvmppc_restore_tm_pr() to do trechkpt.
with updated vcpu tm checkpoint values.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Currently the kernel doesn't use transaction memory.
And there is an issue for privileged state in the guest that:
tbegin/tsuspend/tresume/tabort TM instructions can impact MSR TM bits
without trapping into the PR host. So following code will lead to a
false mfmsr result:
	tbegin	<- MSR bits update to Transaction active.
	beq 	<- failover handler branch
	mfmsr	<- still read MSR bits from magic page with
		transaction inactive.

It is not an issue for non-privileged guest state since its mfmsr is
not patched with magic page and will always trap into the PR host.

This patch will always fail tbegin attempt for privileged state in the
guest, so that the above issue is prevented. It is benign since
currently (guest) kernel doesn't initiate a transaction.

Test case:
https://github.com/justdoitqd/publicFiles/blob/master/test_tbegin_pr.cSigned-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The mfspr/mtspr on TM SPRs(TEXASR/TFIAR/TFHAR) are non-privileged
instructions and can be executed by PR KVM guest in problem state
without trapping into the host. We only emulate mtspr/mfspr
texasr/tfiar/tfhar in guest PR=0 state.

When we are emulating mtspr tm sprs in guest PR=0 state, the emulation
result needs to be visible to guest PR=1 state. That is, the actual TM
SPR val should be loaded into actual registers.

We already flush TM SPRs into vcpu when switching out of CPU, and load
TM SPRs when switching back.

This patch corrects mfspr()/mtspr() emulation for TM SPRs to make the
actual source/dest be the actual TM SPRs.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The transaction memory checkpoint area save/restore behavior is
triggered when VCPU qemu process is switching out/into CPU, i.e.
at kvmppc_core_vcpu_put_pr() and kvmppc_core_vcpu_load_pr().

MSR TM active state is determined by TS bits:
    active: 10(transactional) or 01 (suspended)
    inactive: 00 (non-transactional)
We don't "fake" TM functionality for guest. We "sync" guest virtual
MSR TM active state(10 or 01) with shadow MSR. That is to say,
we don't emulate a transactional guest with a TM inactive MSR.

TM SPR support(TFIAR/TFAR/TEXASR) has already been supported by
commit 9916d57e ("KVM: PPC: Book3S PR: Expose TM registers").
Math register support (FPR/VMX/VSX) will be done at subsequent
patch.

Whether TM context need to be saved/restored can be determined
by kvmppc_get_msr() TM active state:
	* TM active - save/restore TM context
	* TM inactive - no need to do so and only save/restore
TM SPRs.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Suggested-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This patch moves nip/ctr/lr/xer registers from scattered places in
kvm_vcpu_arch to pt_regs structure.

cr register is "unsigned long" in pt_regs and u32 in vcpu->arch.
It will need more consideration and may move in later patches.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Current regs are scattered at kvm_vcpu_arch structure and it will
be more neat to organize them into pt_regs structure.

Also it will enable reimplementation of MMIO emulation code with
analyse_instr() later.
Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Although Linux doesn't use PURR and SPURR ((Scaled) Processor
Utilization of Resources Register), other OSes depend on them.
On POWER8 they count at a rate depending on whether the VCPU is
idle or running, the activity of the VCPU, and the value in the
RWMR (Region-Weighting Mode Register).  Hardware expects the
hypervisor to update the RWMR when a core is dispatched to reflect
the number of online VCPUs in the vcore.

This adds code to maintain a count in the vcore struct indicating
how many VCPUs are online.  In kvmppc_run_core we use that count
to set the RWMR register on POWER8.  If the core is split because
of a static or dynamic micro-threading mode, we use the value for
8 threads.  The RWMR value is not relevant when the host is
executing because Linux does not use the PURR or SPURR register,
so we don't bother saving and restoring the host value.

For the sake of old userspace which does not set the KVM_REG_PPC_ONLINE
register, we set online to 1 if it was 0 at the time of a KVM_RUN
ioctl.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Currently, the HV KVM guest entry/exit code adds the timebase offset
from the vcore struct to the timebase on guest entry, and subtracts
it on guest exit.  Which is fine, except that it is possible for
userspace to change the offset using the SET_ONE_REG interface while
the vcore is running, as there is only one timebase offset per vcore
but potentially multiple VCPUs in the vcore.  If that were to happen,
KVM would subtract a different offset on guest exit from that which
it had added on guest entry, leading to the timebase being out of sync
between cores in the host, which then leads to bad things happening
such as hangs and spurious watchdog timeouts.

To fix this, we add a new field 'tb_offset_applied' to the vcore struct
which stores the offset that is currently applied to the timebase.
This value is set from the vcore tb_offset field on guest entry, and
is what is subtracted from the timebase on guest exit.  Since it is
zero when the timebase offset is not applied, we can simplify the
logic in kvmhv_start_timing and kvmhv_accumulate_time.

In addition, we had secondary threads reading the timebase while
running concurrently with code on the primary thread which would
eventually add or subtract the timebase offset from the timebase.
This occurred while saving or restoring the DEC register value on
the secondary threads.  Although no specific incorrect behaviour has
been observed, this is a race which should be fixed.  To fix it, we
move the DEC saving code to just before we call kvmhv_commence_exit,
and the DEC restoring code to after the point where we have waited
for the primary thread to switch the MMU context and add the timebase
offset.  That way we are sure that the timebase contains the guest
timebase value in both cases.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

POWER9 has hardware bugs relating to transactional memory and thread
reconfiguration (changes to hardware SMT mode).  Specifically, the core
does not have enough storage to store a complete checkpoint of all the
architected state for all four threads.  The DD2.2 version of POWER9
includes hardware modifications designed to allow hypervisor software
to implement workarounds for these problems.  This patch implements
those workarounds in KVM code so that KVM guests see a full, working
transactional memory implementation.

The problems center around the use of TM suspended state, where the
CPU has a checkpointed state but execution is not transactional.  The
workaround is to implement a "fake suspend" state, which looks to the
guest like suspended state but the CPU does not store a checkpoint.
In this state, any instruction that would cause a transition to
transactional state (rfid, rfebb, mtmsrd, tresume) or would use the
checkpointed state (treclaim) causes a "soft patch" interrupt (vector
0x1500) to the hypervisor so that it can be emulated.  The trechkpt
instruction also causes a soft patch interrupt.

On POWER9 DD2.2, we avoid returning to the guest in any state which
would require a checkpoint to be present.  The trechkpt in the guest
entry path which would normally create that checkpoint is replaced by
either a transition to fake suspend state, if the guest is in suspend
state, or a rollback to the pre-transactional state if the guest is in
transactional state.  Fake suspend state is indicated by a flag in the
PACA plus a new bit in the PSSCR.  The new PSSCR bit is write-only and
reads back as 0.

On exit from the guest, if the guest is in fake suspend state, we still
do the treclaim instruction as we would in real suspend state, in order
to get into non-transactional state, but we do not save the resulting
register state since there was no checkpoint.

Emulation of the instructions that cause a softpatch interrupt is
handled in two paths.  If the guest is in real suspend mode, we call
kvmhv_p9_tm_emulation_early() to handle the cases where the guest is
transitioning to transactional state.  This is called before we do the
treclaim in the guest exit path; because we haven't done treclaim, we
can get back to the guest with the transaction still active.  If the
instruction is a case that kvmhv_p9_tm_emulation_early() doesn't
handle, or if the guest is in fake suspend state, then we proceed to
do the complete guest exit path and subsequently call
kvmhv_p9_tm_emulation() in host context with the MMU on.  This handles
all the cases including the cases that generate program interrupts
(illegal instruction or TM Bad Thing) and facility unavailable
interrupts.

The emulation is reasonably straightforward and is mostly concerned
with checking for exception conditions and updating the state of
registers such as MSR and CR0.  The treclaim emulation takes care to
ensure that the TEXASR register gets updated as if it were the guest
treclaim instruction that had done failure recording, not the treclaim
done in hypervisor state in the guest exit path.

With this, the KVM_CAP_PPC_HTM capability returns true (1) even if
transactional memory is not available to host userspace.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When copying between the vcpu and svcpu, we may get scheduled away onto
a different host CPU which in turn means our svcpu pointer may change.

That means we need to atomically copy to and from the svcpu with preemption
disabled, so that all code around it always sees a coherent state.
Reported-by: NSimon Guo <wei.guo.simon@gmail.com>
Fixes: 3d3319b4 ("KVM: PPC: Book3S: PR: Enable interrupts earlier")
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Currently, the HPT code in HV KVM maintains a dirty bit per guest page
in the rmap array, whether or not dirty page tracking has been enabled
for the memory slot.  In contrast, the radix code maintains a dirty
bit per guest page in memslot->dirty_bitmap, and only does so when
dirty page tracking has been enabled.

This changes the HPT code to maintain the dirty bits in the memslot
dirty_bitmap like radix does.  This results in slightly less code
overall, and will mean that we do not lose the dirty bits when
transitioning between HPT and radix mode in future.

There is one minor change to behaviour as a result.  With HPT, when
dirty tracking was enabled for a memslot, we would previously clear
all the dirty bits at that point (both in the HPT entries and in the
rmap arrays), meaning that a KVM_GET_DIRTY_LOG ioctl immediately
following would show no pages as dirty (assuming no vcpus have run
in the meantime).  With this change, the dirty bits on HPT entries
are not cleared at the point where dirty tracking is enabled, so
KVM_GET_DIRTY_LOG would show as dirty any guest pages that are
resident in the HPT and dirty.  This is consistent with what happens
on radix.

This also fixes a bug in the mark_pages_dirty() function for radix
(in the sense that the function no longer exists).  In the case where
a large page of 64 normal pages or more is marked dirty, the
addressing of the dirty bitmap was incorrect and could write past
the end of the bitmap.  Fortunately this case was never hit in
practice because a 2MB large page is only 32 x 64kB pages, and we
don't support backing the guest with 1GB huge pages at this point.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Since commit b009031f ("KVM: PPC: Book3S HV: Take out virtual
core piggybacking code", 2016-09-15), we only have at most one
vcore per subcore.  Previously, the fact that there might be more
than one vcore per subcore meant that we had the notion of a
"master vcore", which was the vcore that controlled thread 0 of
the subcore.  We also needed a list per subcore in the core_info
struct to record which vcores belonged to each subcore.  Now that
there can only be one vcore in the subcore, we can replace the
list with a simple pointer and get rid of the notion of the
master vcore (and in fact treat every vcore as a master vcore).

We can also get rid of the subcore_vm[] field in the core_info
struct since it is never read.
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This adds a few last pieces of the support for radix guests:

* Implement the backends for the KVM_PPC_CONFIGURE_V3_MMU and
  KVM_PPC_GET_RMMU_INFO ioctls for radix guests

* On POWER9, allow secondary threads to be on/off-lined while guests
  are running.

* Set up LPCR and the partition table entry for radix guests.

* Don't allocate the rmap array in the kvm_memory_slot structure
  on radix.

* Don't try to initialize the HPT for radix guests, since they don't
  have an HPT.

* Take out the code that prevents the HV KVM module from
  initializing on radix hosts.

At this stage, we only support radix guests if the host is running
in radix mode, and only support HPT guests if the host is running in
HPT mode.  Thus a guest cannot switch from one mode to the other,
which enables some simplifications.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds code to keep track of dirty pages when requested (that is,
when memslot->dirty_bitmap is non-NULL) for radix guests.  We use the
dirty bits in the PTEs in the second-level (partition-scoped) page
tables, together with a bitmap of pages that were dirty when their
PTE was invalidated (e.g., when the page was paged out).  This bitmap
is stored in the first half of the memslot->dirty_bitmap area, and
kvm_vm_ioctl_get_dirty_log_hv() now uses the second half for the
bitmap that gets returned to userspace.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adapts our implementations of the MMU notifier callbacks
(unmap_hva, unmap_hva_range, age_hva, test_age_hva, set_spte_hva)
to call radix functions when the guest is using radix.  These
implementations are much simpler than for HPT guests because we
have only one PTE to deal with, so we don't need to traverse
rmap chains.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds the code to construct the second-level ("partition-scoped" in
architecturese) page tables for guests using the radix MMU.  Apart from
the PGD level, which is allocated when the guest is created, the rest
of the tree is all constructed in response to hypervisor page faults.

As well as hypervisor page faults for missing pages, we also get faults
for reference/change (RC) bits needing to be set, as well as various
other error conditions.  For now, we only set the R or C bit in the
guest page table if the same bit is set in the host PTE for the
backing page.

This code can take advantage of the guest being backed with either
transparent or ordinary 2MB huge pages, and insert 2MB page entries
into the guest page tables.  There is no support for 1GB huge pages
yet.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This adds a field in struct kvm_arch and an inline helper to
indicate whether a guest is a radix guest or not, plus a new file
to contain the radix MMU code, which currently contains just a
translate function which knows how to traverse the guest page
tables to translate an address.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

POWER8 has one virtual timebase (VTB) register per subcore, not one
per CPU thread.  The HV KVM code currently treats VTB as a per-thread
register, which can lead to spurious soft lockup messages from guests
which use the VTB as the time source for the soft lockup detector.
(CPUs before POWER8 did not have the VTB register.)

For HV KVM, this fixes the problem by making only the primary thread
in each virtual core save and restore the VTB value.  With this,
the VTB state becomes part of the kvmppc_vcore structure.  This
also means that "piggybacking" of multiple virtual cores onto one
subcore is not possible on POWER8, because then the virtual cores
would share a single VTB register.

PR KVM emulates a VTB register, which is per-vcpu because PR KVM
has no notion of CPU threads or SMT.  For PR KVM we move the VTB
state into the kvmppc_vcpu_book3s struct.

Cc: stable@vger.kernel.org # v3.14+
Reported-by: NThomas Huth <thuth@redhat.com>
Tested-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

Add a  module parameter kvm_irq_bypass for kvm_hv.ko to
disable IRQ bypass for passthrough interrupts. The default
value of this tunable is 1 - that is enable the feature.

Since the tunable is used by built-in kernel code, we use
the module_param_cb macro to achieve this.
Signed-off-by: NSuresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

This patch introduces new halt polling functionality into the kvm_hv kernel
module. When a vcore is idle it will poll for some period of time before
scheduling itself out.

When all of the runnable vcpus on a vcore have ceded (and thus the vcore is
idle) we schedule ourselves out to allow something else to run. In the
event that we need to wake up very quickly (for example an interrupt
arrives), we are required to wait until we get scheduled again.

Implement halt polling so that when a vcore is idle, and before scheduling
ourselves, we poll for vcpus in the runnable_threads list which have
pending exceptions or which leave the ceded state. If we poll successfully
then we can get back into the guest very quickly without ever scheduling
ourselves, otherwise we schedule ourselves out as before.

There exists generic halt_polling code in virt/kvm_main.c, however on
powerpc the polling conditions are different to the generic case. It would
be nice if we could just implement an arch specific kvm_check_block()
function, but there is still other arch specific things which need to be
done for kvm_hv (for example manipulating vcore states) which means that a
separate implementation is the best option.

Testing of this patch with a TCP round robin test between two guests with
virtio network interfaces has found a decrease in round trip time of ~15us
on average. A performance gain is only seen when going out of and
back into the guest often and quickly, otherwise there is no net benefit
from the polling. The polling interval is adjusted such that when we are
often scheduled out for long periods of time it is reduced, and when we
often poll successfully it is increased. The rate at which the polling
interval increases or decreases, and the maximum polling interval, can
be set through module parameters.

Based on the implementation in the generic kvm module by Wanpeng Li and
Paolo Bonzini, and on direction from Paul Mackerras.
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The struct kvmppc_vcore is a structure used to store various information
about a virtual core for a kvm guest. The runnable_threads element of the
struct provides a list of all of the currently runnable vcpus on the core
(those in the KVMPPC_VCPU_RUNNABLE state). The previous implementation of
this list was a linked_list. The next patch requires that the list be able
to be iterated over without holding the vcore lock.

Reimplement the runnable_threads list in the kvmppc_vcore struct as an
array. Implement function to iterate over valid entries in the array and
update access sites accordingly.
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

The next commit will introduce a member to the kvmppc_vcore struct which
references MAX_SMT_THREADS which is defined in kvm_book3s_asm.h, however
this file isn't included in kvm_host.h directly. Thus compiling for
certain platforms such as pmac32_defconfig and ppc64e_defconfig with KVM
fails due to MAX_SMT_THREADS not being defined.

Move the struct kvmppc_vcore definition to kvm_book3s.h which explicitly
includes kvm_book3s_asm.h.
Signed-off-by: NSuraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>

To date, we have implemented two I/O usage models for persistent memory,
PMEM (a persistent "ram disk") and DAX (mmap persistent memory into
userspace).  This series adds a third, DAX-GUP, that allows DAX mappings
to be the target of direct-i/o.  It allows userspace to coordinate
DMA/RDMA from/to persistent memory.

The implementation leverages the ZONE_DEVICE mm-zone that went into
4.3-rc1 (also discussed at kernel summit) to flag pages that are owned
and dynamically mapped by a device driver.  The pmem driver, after
mapping a persistent memory range into the system memmap via
devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus
page-backed pmem-pfns via flags in the new pfn_t type.

The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the
resulting pte(s) inserted into the process page tables with a new
_PAGE_DEVMAP flag.  Later, when get_user_pages() is walking ptes it keys
off _PAGE_DEVMAP to pin the device hosting the page range active.
Finally, get_page() and put_page() are modified to take references
against the device driver established page mapping.

Finally, this need for "struct page" for persistent memory requires
memory capacity to store the memmap array.  Given the memmap array for a
large pool of persistent may exhaust available DRAM introduce a
mechanism to allocate the memmap from persistent memory.  The new
"struct vmem_altmap *" parameter to devm_memremap_pages() enables
arch_add_memory() to use reserved pmem capacity rather than the page
allocator.

This patch (of 18):

The core has developed a need for a "pfn_t" type [1].  Move the existing
pfn_t in KVM to kvm_pfn_t [2].

[1]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002199.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002218.htmlSigned-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In 64 bit kernels, the Fixed Point Exception Register (XER) is a 64
bit field (e.g. in kvm_regs and kvm_vcpu_arch) and in most places it is
accessed as such.

This patch corrects places where it is accessed as a 32 bit field by a
64 bit kernel.  In some cases this is via a 32 bit load or store
instruction which, depending on endianness, will cause either the
lower or upper 32 bits to be missed.  In another case it is cast as a
u32, causing the upper 32 bits to be cleared.

This patch corrects those places by extending the access methods to
64 bits.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: NLaurent Vivier <lvivier@redhat.com>
Reviewed-by: NThomas Huth <thuth@redhat.com>
Tested-by: NThomas Huth <thuth@redhat.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This fixes a bug in the tracking of pages that get modified by the
guest.  If the guest creates a large-page HPTE, writes to memory
somewhere within the large page, and then removes the HPTE, we only
record the modified state for the first normal page within the large
page, when in fact the guest might have modified some other normal
page within the large page.

To fix this we use some unused bits in the rmap entry to record the
order (log base 2) of the size of the page that was modified, when
removing an HPTE.  Then in kvm_test_clear_dirty_npages() we use that
order to return the correct number of modified pages.

The same thing could in principle happen when removing a HPTE at the
host's request, i.e. when paging out a page, except that we never
page out large pages, and the guest can only create large-page HPTEs
if the guest RAM is backed by large pages.  However, we also fix
this case for the sake of future-proofing.

The reference bit is also subject to the same loss of information.  We
don't make the same fix here for the reference bit because there isn't
an interface for userspace to find out which pages the guest has
referenced, whereas there is one for userspace to find out which pages
the guest has modified.  Because of this loss of information, the
kvm_age_hva_hv() and kvm_test_age_hva_hv() functions might incorrectly
say that a page has not been referenced when it has, but that doesn't
matter greatly because we never page or swap out large pages.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

On POWER, storage caching is usually configured via the MMU - attributes
such as cache-inhibited are stored in the TLB and the hashed page table.

This makes correctly performing cache inhibited IO accesses awkward when
the MMU is turned off (real mode).  Some CPU models provide special
registers to control the cache attributes of real mode load and stores but
this is not at all consistent.  This is a problem in particular for SLOF,
the firmware used on KVM guests, which runs entirely in real mode, but
which needs to do IO to load the kernel.

To simplify this qemu implements two special hypercalls, H_LOGICAL_CI_LOAD
and H_LOGICAL_CI_STORE which simulate a cache-inhibited load or store to
a logical address (aka guest physical address).  SLOF uses these for IO.

However, because these are implemented within qemu, not the host kernel,
these bypass any IO devices emulated within KVM itself.  The simplest way
to see this problem is to attempt to boot a KVM guest from a virtio-blk
device with iothread / dataplane enabled.  The iothread code relies on an
in kernel implementation of the virtio queue notification, which is not
triggered by the IO hcalls, and so the guest will stall in SLOF unable to
load the guest OS.

This patch addresses this by providing in-kernel implementations of the
2 hypercalls, which correctly scan the KVM IO bus.  Any access to an
address not handled by the KVM IO bus will cause a VM exit, hitting the
qemu implementation as before.

Note that a userspace change is also required, in order to enable these
new hcall implementations with KVM_CAP_PPC_ENABLE_HCALL.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
[agraf: fix compilation]
Signed-off-by: NAlexander Graf <agraf@suse.de>

These don't seem to be used anywhere.
Acked-by: NRik van Riel <riel@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will deacon <will.deacon@arm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>

This removes the code that was added to enable HV KVM to work
on PPC970 processors.  The PPC970 is an old CPU that doesn't
support virtualizing guest memory.  Removing PPC970 support also
lets us remove the code for allocating and managing contiguous
real-mode areas, the code for the !kvm->arch.using_mmu_notifiers
case, the code for pinning pages of guest memory when first
accessed and keeping track of which pages have been pinned, and
the code for handling H_ENTER hypercalls in virtual mode.

Book3S HV KVM is now supported only on POWER7 and POWER8 processors.
The KVM_CAP_PPC_RMA capability now always returns 0.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We handle FSCR feature bits (well, TAR only really today) lazily when the guest
starts using them. So when a guest activates the bit and later uses that feature
we enable it for real in hardware.

However, when the guest stops using that bit we don't stop setting it in
hardware. That means we can potentially lose a trap that the guest expects to
happen because it thinks a feature is not active.

This patch adds support to drop TAR when then guest turns it off in FSCR. While
at it it also restricts FSCR access to 64bit systems - 32bit ones don't have it.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We use kvmppc_ld and kvmppc_st to emulate load/store instructions that may as
well access the magic page. Special case it out so that we can properly access
it.
Signed-off-by: NAlexander Graf <agraf@suse.de>

We have enough common infrastructure now to resolve GVA->GPA mappings at
runtime. With this we can move our book3s specific helpers to load / store
in guest virtual address space to common code as well.
Signed-off-by: NAlexander Graf <agraf@suse.de>

On book3e, guest last instruction is read on the exit path using load
external pid (lwepx) dedicated instruction. This load operation may fail
due to TLB eviction and execute-but-not-read entries.

This patch lay down the path for an alternative solution to read the guest
last instruction, by allowing kvmppc_get_lat_inst() function to fail.
Architecture specific implmentations of kvmppc_load_last_inst() may read
last guest instruction and instruct the emulation layer to re-execute the
guest in case of failure.

Make kvmppc_get_last_inst() definition common between architectures.
Signed-off-by: NMihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

The magic page is defined as a 4k page of per-vCPU data that is shared
between the guest and the host to accelerate accesses to privileged
registers.

However, when the host is using 64k page size granularity we weren't quite
as strict about that rule anymore. Instead, we partially treated all of the
upper 64k as magic page and mapped only the uppermost 4k with the actual
magic contents.

This works well enough for Linux which doesn't use any memory in kernel
space in the upper 64k, but Mac OS X got upset. So this patch makes magic
page actually stay in a 4k range even on 64k page size hosts.

This patch fixes magic page usage with Mac OS X (using MOL) on 64k PAGE_SIZE
hosts for me.
Signed-off-by: NAlexander Graf <agraf@suse.de>