Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

it was device configuration setting function, not only speed.
This patch modify function name usbhs_set_device_speed() -> usbhs_set_device_config()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DCP data/status stage needs ureq to usbhs_pkt_push(),
but sometimes, there is no data stage.
In that case, allocated ureq was not freed,
Current ureq alloc/free pair were difficult to understand.
This patch removed unnecessary/un-understandable ureq alloc
from usbhsh_urb_enqueue(), and create simpler alloc/free pair.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

With Peiyu's patch "gadget: mass_storage: adapt logic block size to bound block
devices" (http://www.spinics.net/lists/linux-usb/msg50791.html), now mass storage
can adjust logic block size dynamically based on real devices.
Then there is one issue caused by it, if two luns have different logic block size,
mass storage can't work.
Let's check the current software flow:
1. get_next_command(): call received_cbw();
2. received_cbw(): update common->lun = cbw->Lun, but common->curlen is not updated;
3. do_scsi_command(): in READ_X and WRITE_X commands, common->data_size_from_cmnd is
updated by common->curlun->blkbits;
4. check_command(): update common->curlun according to common->lun
As you can see, the step 3 uses wrong common->curlun, then wrong common->curlun->blkbits.
If the two luns have same blkbits, there isn't issue. Otherwise, both will fail.
This patch moves the common->curlun update to step 1, then make sure step 3 gets right
blkbits and data_size_from_cmnd.

Cc: Peiyu Li <peiyu.li@csr.com>
Signed-off-by: NYuPing Luo <yuping.luo@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

renesas_usbhs needs callback for notify hotplug.
but it were 2 methods which are almost same.
This patch unified these into one.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

detection_delay was assumed as msec
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

renesas_usbhs driver use "req" for struct usb_ctrlrequest,
and "ureq" for struct usbhsh_request
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

usbhs_sys_usb_ctrl() can collect into usbhs_sys_host/function_ctrl().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

usbhs_sys_hispeed_ctrl() can collect into usbhs_sys_host/function_ctrl().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The ci13xxx_udc driver checks the number of endpoints in the udc
controller, however some routines expect that the hardware has 16
bidirectional endpoints.

This patch improves the driver to work on controllers with less than
16 endpoints like the udc controller found on freescale's
mx23 and mx28.
Tested-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some gadget drivers don't implement suspend and/or resume functions.
Instead of changing the gadget drivers, make suspend and resume in
ci13xxx_udc (following other udc drivers) optional.
Tested-by: NPavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NMarcin Kościelnicki <koriakin@0x04.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts commit df711fc9.

The commit added a reset-on-resume quirk because the NEC chipset stopped
responding to commands about 30 minutes after a system resume from
suspend.  We thought it was a chipset issue, but it turns out that the
xHCI driver was zeroing out the link TRB after a successful context
restore during resume.  The host controller would fall off the command
ring sometime later, causing it to not respond to new commands.

The link TRB issue has been fixed with commit
158886cd "xHCI: fix bug in
xhci_clear_command_ring()", so revert the reset-on-resume quirk, as it's
not necessary.

Commit df711fc9 was marked for stable
trees back to 2.6.37, but according to my mail, it has not made it into
Linus' tree or the stable trees yet.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NJulian Sikorski <belegdol@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>

When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.

When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.

This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NOliver Neukum <oneukum@suse.de>

The original implementation of dequeuing a request in progress
is not correct.  Change to use a correct process and also clean
up the related functions a little bit.
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In order to support multiple SoC kernel image, compile-time dependency
on a specific SoC type should be avoided.

fsl_udc_clk_finalize is already protected by cpu_is_mx35(), so remove
the compile-time check for CONFIG_SOC_IMX35.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the following build error:

CC [M]  drivers/usb/gadget/fsl_mxc_udc.o
drivers/usb/gadget/fsl_mxc_udc.c: In function 'fsl_udc_clk_finalize':
drivers/usb/gadget/fsl_mxc_udc.c:98: error: implicit declaration of function 'readl'
drivers/usb/gadget/fsl_mxc_udc.c:100: error: implicit declaration of function 'writel'

This error is caused by the follwing commit:
(16fcb63: arm/imx: remove mx31_setup_weimcs( ) from mx31.h)

,which removed '#include <linux/io.h>' from mx31.h.

fsl_mxc_udc.c includes <mach/hardware.h>, which in turns includes mx31.h, so
that's the reason fsl_mxc_udc.c built fine previously.

Instead of relying on the indirect inclusion of the linux/io.h header file,
include it directly in fsl_mxc_udc.c.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some ISO gadgets, like audio, has SYNC attribute as well as
USB_ENDPOINT_XFER_ISOC for their bmAttributes at ISO endpoint
descriptor. So, it needs to use usb_endpoint_xfer_isoc to judge
ISO XFER.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Acked-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Several UDC drivers had a gadget driver's speed sanity check of the
form of:

	driver->speed != USB_SPEED_HIGH

or:

	driver->speed != USB_SPEED_HIGH && driver->speed != USB_SPEED_FULL

As more and more gadget drivers support USB SuperSpeed, driver->speed
may be set to USB_SPEED_SUPER and UDC driver should handle such gadget
correctly.  The above checks however fail to recognise USB_SPEED_SUPER
as a valid speed.

This commit changes the two checks to:

	driver->speed < USB_SPEED_HIGH

or:

	driver->speed < USB_SPEED_FULL

respectively.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit "usb: gadget: use config_ep_by_speed() instead of
ep_choose()" broke g_serial in "non ACM nor OBEX"
mode. Apply a trivial fix on usb endpoints discovery.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch cares latest USB_SPEED_SUPER support.
renesas_usbhs can not use super-speed, but can use full/high speed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

current renesas_usbhs is using new style udc_start/stop from
af1d7056
(usb: gadget: renesas: convert to new style).

But current renesas_usbhs driver didn't care about gadget.dev.driver
when udc_stop. it cause rmmod oops.
This patch care it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

current renesas_usbhs is using new style udc_start/stop from
af1d7056
(usb: gadget: renesas: convert to new style).

cable disconnected signal was needed.
This patch fixup it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

current renesas_usbhs is using new style udc_start/stop from
af1d7056
(usb: gadget: renesas: convert to new style).

But bind() function will fail if it was called before
device_register() (or device_add()).
This patch modifies this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently the driver tries to save context in the suspend path, but
will cause an abort if the device is already runtime suspended.  This
happens, for example, if MUSB loaded/compiled-in, in host mode, but no
USB devices are attached.  MUSB will be runtime suspended, but then
attempting a system suspend will crash due to the context save
being attempted while the device is disabled.

On OMAP, as of v3.1, the driver's ->runtime_suspend() callback will be
called late in the suspend path (by the PM domain layer) if the driver
is not already runtime suspended, ensuring a full shutdown.

Therefore, the context save is not needed in the ->suspend() method
since it will be called in the ->runtime_suspend() method anyways
(similarily for resume.)

NOTE: this leaves the suspend/resume methods basically empty (with
      some FIXMEs and comments, but I'll leave it to the maintainers
      to decide whether to remove them.

Cc: stable@vger.kernel.org
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a regression that was introduced by commit
811c926c (USB: EHCI: fix HUB TT scheduling
issue with iso transfer).

We detect an error if next == start, but this means uframe 0 can't be allocated
anymore for iso transfer...
Reported-by: NSander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Julian Sikorski reports NEC uPD720200 does not work stable after suspend
and resume. Re-initialize the host in xhci_resume().

This should be backported to stable kernels as old as 2.6.37.  The
kernel will need to include
commit c877b3b2
"xhci: Add reset on resume quirk for asrock p67 host"
for this patch to work.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Reported-by: NJulian Sikorski <belegdol@gmail.com>
Tested-by: NJulian Sikorski <belegdol@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

qset->qh.link is an __le64 field and we should be using cpu_to_le64()
to fill it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kingston DT 101 G2 replies a wrong tag while transporting, add an
unusal_devs entry to ignore the tag validation.
Signed-off-by: NQinglin Ye <yestyle@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Tested with SIM5218EVB-KIT evaluation kit.
Signed-off-by: NVeli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch creates the missing controlling devices for the Huawei E353
HSPA+ stick.
Signed-off-by: NDirk Nehring <dnehring@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix for ftdi_set_termios() glitching output

ftdi_set_termios() is constantly setting the baud rate, data bits and parity
unnecessarily on every call, . When called while characters are being
transmitted can cause the FTDI chip to corrupt the serial port bit stream
output by stalling the output half a bit during the output of a character.
Simple fix by skipping this setting if the baud rate/data bits/parity are
unchanged.
Signed-off-by: NAndrew Worsley <amworsley@gmail.com>
Cc: stable <stable@vger.kernel.org>
----

  I had a brief run with strace on the getty and it was doing ioctl()s on
  each call but it didn't look relavant to the problem. I think the issue is
  that XON/XOFF flow control was being implmented via hardware - for the ixoff
  to allow the user to use XON/XOFF to control output. Unfortunately it would
  send 3 Control URBs updating all of the settings after each piece of input

  I am trying to work around the issue of gmail messing with the tab/spacing
  by submitting via SMTP via gmail which I believe should fix the issue.

  The patch is against v3.2-rc2 and compiles - but no additional testing in
  this kernel has been done.

  Thanks

   Andrew
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NFerenc Wagner <wferi@niif.hu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Problems with NVIDIA's OHCI host controllers persist.  After looking
carefully through the spec, I finally realized that when a controller
is reset it then automatically goes into a SUSPEND state in which it
is completely quiescent (no DMA and no IRQs) and from which it will
not awaken until the system puts it into the OPERATIONAL state.

Therefore there's no need to worry about controllers being in the
RESET state for extended periods, or remaining in the OPERATIONAL
state during system shutdown.  The proper action for device
initialization is to put the controller into the RESET state (if it's
not there already) and then to issue a software reset.  Similarly, the
proper action for device shutdown is simply to do a software reset.

This patch (as1499) implements such an approach.  It simplifies
initialization and shutdown, and allows the NVIDIA shutdown-quirk code
to be removed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NAndre "Osku" Schmidt <andre.osku.schmidt@googlemail.com>
Tested-by: NArno Augustin <Arno.Augustin@web.de>
Cc: stable <stable@vger.kernel.org> [after tested in 3.2 for a while]
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds new PIDs for ZTE 3G modem, after we confirm it and tested.
Thanks for Dan's work at kernel option devier.
Signed-off-by: NAlvin.Zheng <zheng.zhijian@zte.com.cn>
Signed-off-by: Nwsalvin <wsalvin@yahoo.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix compile error, HC_LENGTH now takes two parameters and ehci
needs to be passed as the first parameter.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>