stable inclusion
from stable-5.10.24
commit a5190a7865b6c49316b41ffd49546c4bdba2f47c
bugzilla: 51348

--------------------------------

commit 165bc5a4 upstream.

According  to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask.  Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.

Fixes: 6e0bb04d ("sh_eth: Add R7S9210 support")
Signed-off-by: NSergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 845ec460537dcf07fa97f093612fa51c6247295a
bugzilla: 51348

--------------------------------

commit 20d7d1c5 upstream.

The following trace excerpt corresponds with a NULL pointer dereference
of 'bp->irq_tbl' in bnxt_setup_inta() on an Aarch64 system after many
device resets:

    Unable to handle kernel NULL pointer dereference at ... 000000d
    ...
    pc : string+0x3c/0x80
    lr : vsnprintf+0x294/0x7e0
    sp : ffff00000f61ba70 pstate : 20000145
    x29: ffff00000f61ba70 x28: 000000000000000d
    x27: ffff0000009c8b5a x26: ffff00000f61bb80
    x25: ffff0000009c8b5a x24: 0000000000000012
    x23: 00000000ffffffe0 x22: ffff000008990428
    x21: ffff00000f61bb80 x20: 000000000000000d
    x19: 000000000000001f x18: 0000000000000000
    x17: 0000000000000000 x16: ffff800b6d0fb400
    x15: 0000000000000000 x14: ffff800b7fe31ae8
    x13: 00001ed16472c920 x12: ffff000008c6b1c9
    x11: ffff000008cf0580 x10: ffff00000f61bb80
    x9 : 00000000ffffffd8 x8 : 000000000000000c
    x7 : ffff800b684b8000 x6 : 0000000000000000
    x5 : 0000000000000065 x4 : 0000000000000001
    x3 : ffff0a00ffffff04 x2 : 000000000000001f
    x1 : 0000000000000000 x0 : 000000000000000d
    Call trace:
    string+0x3c/0x80
    vsnprintf+0x294/0x7e0
    snprintf+0x44/0x50
    __bnxt_open_nic+0x34c/0x928 [bnxt_en]
    bnxt_open+0xe8/0x238 [bnxt_en]
    __dev_open+0xbc/0x130
    __dev_change_flags+0x12c/0x168
    dev_change_flags+0x20/0x60
    ...

Ordinarily, a call to bnxt_setup_inta() (not in trace due to inlining)
would not be expected on a system supporting MSIX at all. However, if
bnxt_init_int_mode() does not end up being called after the call to
bnxt_clear_int_mode() in bnxt_fw_reset_close(), then the driver will
think that only INTA is supported and bp->irq_tbl will be NULL,
causing the above crash.

In the error recovery scenario, we call bnxt_clear_int_mode() in
bnxt_fw_reset_close() early in the sequence. Ordinarily, we will
call bnxt_init_int_mode() in bnxt_hwrm_if_change() after we
reestablish communication with the firmware after reset.  However,
if the sequence has to abort before we call bnxt_init_int_mode() and
if the user later attempts to re-open the device, then it will cause
the crash above.

We fix it in 2 ways:

1. Check for bp->irq_tbl in bnxt_setup_int_mode(). If it is NULL, call
bnxt_init_init_mode().

2. If we need to abort in bnxt_hwrm_if_change() and cannot complete
the error recovery sequence, set the BNXT_STATE_ABORT_ERR flag.  This
will cause more drastic recovery at the next attempt to re-open the
device, including a call to bnxt_init_int_mode().

Fixes: 3bc7d4a3 ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit fd61e772f036601f267aadaecee789bd251baec2
bugzilla: 51348

--------------------------------

commit b36fc875 upstream.

The function hclge_fd_convert_tuple() is used to convert tuples
and tuples mask to TCAM x and y.  But it misuses the source mac
as source mac mask when convert INNER_SRC_MAC, which may cause
the flow director rule works unexpectedly. So fix it.

Fixes: 11732868 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 3c7f1304ee718b4f3c5eca8b2b1545ecd2227a8d
bugzilla: 51348

--------------------------------

commit c75ec148 upstream.

Currently, the driver returns VLAN_VID_MASK for vlan mask field,
when get flow director rule information for rule doesn't use vlan.
It may cause the vlan mask value display as 0xf000 in this
case, like below:

estuary:/$ ethtool -u eth1
50 RX rings available
Total 1 rules

Filter: 2
Rule Type: TCP over IPv4
Src IP addr: 0.0.0.0 mask: 255.255.255.255
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xf000
User-defined: 0x1234 mask: 0x0
Action: Direct to queue 3

Fix it by return 0.

Fixes: 05c2314f ("net: hns3: Add support for rule query of flow director")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit e4f7ffaa7cdfe7b680ede760f3a3ad5e1d12f049
bugzilla: 51348

--------------------------------

commit ae9b24dd upstream.

Currently, only external bits are added to the PTYS register, whereas
there is one external bit that is wrongly marked as internal, and so was
recently removed from the register.

Add that bit to the PTYS register again, as this bit is no longer
internal.

Its removal resulted in '100000baseLR4_ER4/Full' link mode no longer
being supported, causing a regression on some setups.

Fixes: 5bf01b57 ("mlxsw: spectrum_ethtool: Remove internal speeds from PTYS register")
Signed-off-by: NDanielle Ratson <danieller@nvidia.com>
Reported-by: NEddie Shklaer <eddies@nvidia.com>
Tested-by: NEddie Shklaer <eddies@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 482f99d0ad393abede12d3b80fcb5b8900d399d1
bugzilla: 51348

--------------------------------

commit 396e13e1 upstream.

In current driver, buffer2 available only when hardware supports split
header. Wrongly set buffer2 valid in stmmac_rx_refill when refill buffer
address. You can see that desc3 is 0x81000000 after initialization, but
turn out to be 0x83000000 after refill.

Fixes: 67afd6d1 ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 333dbdee0651d928389a7096c72ad1c8adc624d4
bugzilla: 51348

--------------------------------

commit c511819d upstream.

stmmac_xmit() call stmmac_tx_timer_arm() at the end to modify tx timer to
do the transmission cleanup work. Imagine such a situation, stmmac enters
suspend immediately after tx timer modified, it's expire callback
stmmac_tx_clean() would not be invoked. This could affect BQL, since
netdev_tx_sent_queue() has been called, but netdev_tx_completed_queue()
have not been involved, as a result, dql_avail(&dev_queue->dql) finally
always return a negative value.

__dev_queue_xmit->__dev_xmit_skb->qdisc_run->__qdisc_run->qdisc_restart->dequeue_skb:
	if ((q->flags & TCQ_F_ONETXQUEUE) &&
		netif_xmit_frozen_or_stopped(txq)) // __QUEUE_STATE_STACK_XOFF is set

Net core will stop transmitting any more. Finillay, net watchdong would timeout.
To fix this issue, we should call netdev_tx_reset_queue() in stmmac_resume().

Fixes: 54139cf3 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 3c1b58261ff81fba9f6bd8f8d9bcec85920c2ff0
bugzilla: 51348

--------------------------------

commit a3e860a8 upstream.

If clear GMAC_CONFIG_TE bit, it would stop all tx channels, but users
may only want to stop specific tx channel.

Fixes: 48863ce5 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit ee7eac24b5b495f484034cdb2bd7152edc5a985f
bugzilla: 51348

--------------------------------

commit d785e1fe upstream.

Based on talks and indirect references ixgbe IPsec offlod do not
support IPsec tunnel mode offload. It can only support IPsec transport
mode offload. Now explicitly fail when creating non transport mode SA
with offload to avoid false performance expectations.

Fixes: 63a67fe2 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: NAntony Antony <antony@phenome.org>
Acked-by: NShannon Nelson <snelson@pensando.io>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit cab735320fe92b40d1f69b93a20694117aa2d5a5
bugzilla: 51348

--------------------------------

commit abbf9a0e upstream.

The (0xBAF70000 & 0x00FFF000) << 6 should be (0xf70 << 18).

Fixes: 561535b0 ("r8169: fix OCP access on RTL8117")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 4f8e71a770dd460c9e8ac40baceefef6d8853b13
bugzilla: 51348

--------------------------------

commit 29d98f54 upstream.

The txtime is passed to the driver in skb->skb_mstamp_ns, which is
actually in a union with skb->tstamp (the place where software
timestamps are kept).

Since commit b50a5c70 ("net: allow simultaneous SW and HW transmit
timestamping"), __sock_recv_timestamp has some logic for making sure
that the two calls to skb_tstamp_tx:

skb_tx_timestamp(skb) # Software timestamp in the driver
-> skb_tstamp_tx(skb, NULL)

and

skb_tstamp_tx(skb, &shhwtstamps) # Hardware timestamp in the driver

will both do the right thing and in a race-free manner, meaning that
skb_tx_timestamp will deliver a cmsg with the software timestamp only,
and skb_tstamp_tx with a non-NULL hwtstamps argument will deliver a cmsg
with the hardware timestamp only.

Why are races even possible? Well, because although the software timestamp
skb->tstamp is private per skb, the hardware timestamp skb_hwtstamps(skb)
lives in skb_shinfo(skb), an area which is shared between skbs and their
clones. And skb_tstamp_tx works by cloning the packets when timestamping
them, therefore attempting to perform hardware timestamping on an skb's
clone will also change the hardware timestamp of the original skb. And
the original skb might have been yet again cloned for software
timestamping, at an earlier stage.

So the logic in __sock_recv_timestamp can't be as simple as saying
"does this skb have a hardware timestamp? if yes I'll send the hardware
timestamp to the socket, otherwise I'll send the software timestamp",
precisely because the hardware timestamp is shared.
Instead, it's quite the other way around: __sock_recv_timestamp says
"does this skb have a software timestamp? if yes, I'll send the software
timestamp, otherwise the hardware one". This works because the software
timestamp is not shared with clones.

But that means we have a problem when we attempt hardware timestamping
with skbs that don't have the skb->tstamp == 0. __sock_recv_timestamp
will say "oh, yeah, this must be some sort of odd clone" and will not
deliver the hardware timestamp to the socket. And this is exactly what
is happening when we have txtime enabled on the socket: as mentioned,
that is put in a union with skb->tstamp, so it is quite easy to mistake
it.

Do what other drivers do (intel igb/igc) and write zero to skb->tstamp
before taking the hardware timestamp. It's of no use to us now (we're
already on the TX confirmation path).

Fixes: 0d08c9ec ("enetc: add support time specific departure base on the qos etf")
Cc: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 4fd0654b8f2129b68203974ddee15f804ec011c2
bugzilla: 51348

--------------------------------

commit cf9e60aa upstream.

We must disable the regulator that was enabled in the probe function.

Fixes: 7994fe55 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit e334c401f3fc9fdf2321e14a5204d591a0713e7f
bugzilla: 51348

--------------------------------

commit ac88c531 upstream.

When the probe fails or requests to be defered, we must disable the
regulator that was previously enabled.

Fixes: 7994fe55 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: NPaul Cercueil <paul@crapouillou.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 9c4136081cc2076ca981e68001b3cb8f53800a94
bugzilla: 51348

--------------------------------

commit 8eb37ab7 upstream.

Issue seen when enumerating multiple Intel mGbE interfaces in EHL.

[    6.898141] intel-eth-pci 0000:00:1d.2: enabling device (0000 -> 0002)
[    6.900971] intel-eth-pci 0000:00:1d.2: Fail to register stmmac-clk
[    6.906434] intel-eth-pci 0000:00:1d.2: User ID: 0x51, Synopsys ID: 0x52

We fix it by making the clock name to be unique following the format
of stmmac-pci_name(pci_dev) so that we can differentiate the clock for
these Intel mGbE interfaces in EHL platform as follow:

  /sys/kernel/debug/clk/stmmac-0000:00:1d.1
  /sys/kernel/debug/clk/stmmac-0000:00:1d.2
  /sys/kernel/debug/clk/stmmac-0000:00:1e.4

Fixes: 58da0cfa ("net: stmmac: create dwmac-intel.c to contain all Intel platform")
Signed-off-by: NWong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: NVoon Weifeng <weifeng.voon@intel.com>
Co-developed-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit d78f23ef304060608bc9b1627f303842f75d7029
bugzilla: 51348

--------------------------------

commit 9a7b3950 upstream.

For Intel mGbE controller, MAC VLAN filter delete operation will time-out
if serdes power-down sequence happened first during driver remove() with
below message.

[82294.764958] intel-eth-pci 0000:00:1e.4 eth2: stmmac_dvr_remove: removing driver
[82294.778677] intel-eth-pci 0000:00:1e.4 eth2: Timeout accessing MAC_VLAN_Tag_Filter
[82294.779997] intel-eth-pci 0000:00:1e.4 eth2: failed to kill vid 0081/0
[82294.947053] intel-eth-pci 0000:00:1d.2 eth1: stmmac_dvr_remove: removing driver
[82295.002091] intel-eth-pci 0000:00:1d.1 eth0: stmmac_dvr_remove: removing driver

Therefore, we delay the serdes power-down to be after unregister_netdev()
which triggers the VLAN filter delete.

Fixes: b9663b7c ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 719611e806deea598088541bd4509a3735d29c92
bugzilla: 51348

--------------------------------

commit f1becbed upstream.

An attempt is made to warn the user about the fact that VCAP IS1 cannot
offload keys matching on destination IP (at least given the current half
key format), but sadly that warning fails miserably in practice, due to
the fact that it operates on an uninitialized "match" variable. We must
first decode the keys from the flow rule.

Fixes: 75944fda ("net: mscc: ocelot: offload ingress skbedit and vlan actions to VCAP IS1")
Reported-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 87b7b19d6e1dabbd12344b2784b78ea8b4992f6f
bugzilla: 51348

--------------------------------

commit 879c348c upstream.

We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.

Fixes: 48863ce5 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NRamesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 6b0d3ae1051bdca4acf91a66be64d42d1c0f577b
bugzilla: 51348

--------------------------------

commit 00ff801b upstream.

This patch fixes a bug that the moderation config will not be
applied when calling mlx4_en_reset_config. For example, when
turning on rx timestamping, mlx4_en_reset_config() will be called,
causing the NIC to forget previous moderation config.

This fix is in phase with a previous fix:
commit 79c54b6b ("net/mlx4_en: Fix TX moderation info loss
after set_ringparam is called")

Tested: Before this patch, on a host with NIC using mlx4, run
netserver and stream TCP to the host at full utilization.
$ sar -I SUM 1
                 INTR    intr/s
14:03:56          sum  48758.00

After rx hwtstamp is enabled:
$ sar -I SUM 1
14:10:38          sum 317771.00
We see the moderation is not working properly and issued 7x more
interrupts.

After the patch, and turned on rx hwtstamp, the rate of interrupts
is as expected:
$ sar -I SUM 1
14:52:11          sum  49332.00

Fixes: 79c54b6b ("net/mlx4_en: Fix TX moderation info loss after set_ringparam is called")
Signed-off-by: NKevin(Yudong) Yang <yyd@google.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NNeal Cardwell <ncardwell@google.com>
CC: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit fa0bc09db49bf4875d9a8c88813fe2b87c1059bb
bugzilla: 51348

--------------------------------

commit 95b39f07 upstream.

mtk_star_dma_unmap_rx() should unmap the dma_addr of old skb rather than
that of new skb.
Assign new_dma_addr to desc_data.dma_addr after all handling of old skb
ends to avoid unexpected receive side error.

Fixes: f96e9641 ("net: ethernet: mtk-star-emac: fix error path in RX handling")
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 1cdd008902d4e32f270e8fdb3239db6412f0a90b
bugzilla: 51348

--------------------------------

commit 3a5d12c9 upstream.

The RX rings have a producer index owned by hardware, where newly
received frame buffers are placed, and a consumer index owned by
software, where newly allocated buffers are placed, in expectation of
hardware being able to place frame data in them.

Hardware increments the producer index when a frame is received, however
it is not allowed to increment the producer index to match the consumer
index (RBCIR) since the ring can hold at most RBLENR[LENGTH]-1 received
BDs. Whenever the producer index matches the value of the consumer
index, the ring has no unprocessed received frames and all BDs in the
ring have been initialized/prepared by software, i.e. hardware owns all
BDs in the ring.

The code uses the next_to_clean variable to keep track of the producer
index, and the next_to_use variable to keep track of the consumer index.

The RX rings are seeded from enetc_refill_rx_ring, which is called from
two places:

1. initially the ring is seeded until full with enetc_bd_unused(rx_ring),
   i.e. with 511 buffers. This will make next_to_clean=0 and next_to_use=511:

.ndo_open
-> enetc_open
   -> enetc_setup_bdrs
      -> enetc_setup_rxbdr
         -> enetc_refill_rx_ring

2. then during the data path processing, it is refilled with 16 buffers
   at a time:

enetc_msix
-> napi_schedule
   -> enetc_poll
      -> enetc_clean_rx_ring
         -> enetc_refill_rx_ring

There is just one problem: the initial seeding done during .ndo_open
updates just the producer index (ENETC_RBPIR) with 0, and the software
next_to_clean and next_to_use variables. Notably, it will not update the
consumer index to make the hardware aware of the newly added buffers.

Wait, what? So how does it work?

Well, the reset values of the producer index and of the consumer index
of a ring are both zero. As per the description in the second paragraph,
it means that the ring is full of buffers waiting for hardware to put
frames in them, which by coincidence is almost true, because we have in
fact seeded 511 buffers into the ring.

But will the hardware attempt to access the 512th entry of the ring,
which has an invalid BD in it? Well, no, because in order to do that, it
would have to first populate the first 511 entries, and the NAPI
enetc_poll will kick in by then. Eventually, after 16 processed slots
have become available in the RX ring, enetc_clean_rx_ring will call
enetc_refill_rx_ring and then will [ finally ] update the consumer index
with the new software next_to_use variable. From now on, the
next_to_clean and next_to_use variables are in sync with the producer
and consumer ring indices.

So the day is saved, right? Well, not quite. Freeing the memory
allocated for the rings is done in:

enetc_close
-> enetc_clear_bdrs
   -> enetc_clear_rxbdr
      -> this just disables the ring
-> enetc_free_rxtx_rings
   -> enetc_free_rx_ring
      -> sets next_to_clean and next_to_use to 0

but again, nothing is committed to the hardware producer and consumer
indices (yay!). The assumption is that the ring is disabled, so the
indices don't matter anyway, and it's the responsibility of the "open"
code path to set those up.

.. Except that the "open" code path does not set those up properly.

While initially, things almost work, during subsequent enetc_close ->
enetc_open sequences, we have problems. To be precise, the enetc_open
that is subsequent to enetc_close will again refill the ring with 511
entries, but it will leave the consumer index untouched. Untouched
means, of course, equal to the value it had before disabling the ring
and draining the old buffers in enetc_close.

But as mentioned, enetc_setup_rxbdr will at least update the producer
index though, through this line of code:

	enetc_rxbdr_wr(hw, idx, ENETC_RBPIR, 0);

so at this stage we'll have:

next_to_clean=0 (in hardware 0)
next_to_use=511 (in hardware we'll have the refill index prior to enetc_close)

Again, the next_to_clean and producer index are in sync and set to
correct values, so the driver manages to limp on. Eventually, 16 ring
entries will be consumed by enetc_poll, and the savior
enetc_clean_rx_ring will come and call enetc_refill_rx_ring, and then
update the hardware consumer ring based upon the new next_to_use.

So.. it works?
Well, by coincidence, it almost does, but there's a circumstance where
enetc_clean_rx_ring won't be there to save us. If the previous value of
the consumer index was 15, there's a problem, because the NAPI poll
sequence will only issue a refill when 16 or more buffers have been
consumed.

It's easiest to illustrate this with an example:

ip link set eno0 up
ip addr add 192.168.100.1/24 dev eno0
ping 192.168.100.1 -c 20 # ping this port from another board
ip link set eno0 down
ip link set eno0 up
ping 192.168.100.1 -c 20 # ping it again from the same other board

One by one:

1. ip link set eno0 up
-> calls enetc_setup_rxbdr:
   -> calls enetc_refill_rx_ring(511 buffers)
   -> next_to_clean=0 (in hw 0)
   -> next_to_use=511 (in hw 0)

2. ping 192.168.100.1 -c 20 # ping this port from another board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=15 next_to_clean 14 (in hw 15) next_to_use 511 (in hw 0)
enetc_clean_rx_ring: enetc_refill_rx_ring(16) increments next_to_use by 16 (mod 512) and writes it to hw
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=0 next_to_clean 15 (in hw 16) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 16 (in hw 17) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 17 (in hw 18) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 18 (in hw 19) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 19 (in hw 20) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 20 (in hw 21) next_to_use 15 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 21 (in hw 22) next_to_use 15 (in hw 15)

20 packets transmitted, 20 packets received, 0% packet loss

3. ip link set eno0 down
enetc_free_rx_ring: next_to_clean 0 (in hw 22), next_to_use 0 (in hw 15)

4. ip link set eno0 up
-> calls enetc_setup_rxbdr:
   -> calls enetc_refill_rx_ring(511 buffers)
   -> next_to_clean=0 (in hw 0)
   -> next_to_use=511 (in hw 15)

5. ping 192.168.100.1 -c 20 # ping it again from the same other board
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=1 next_to_clean 0 (in hw 1) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=2 next_to_clean 1 (in hw 2) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=3 next_to_clean 2 (in hw 3) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=4 next_to_clean 3 (in hw 4) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=5 next_to_clean 4 (in hw 5) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=6 next_to_clean 5 (in hw 6) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=7 next_to_clean 6 (in hw 7) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=8 next_to_clean 7 (in hw 8) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=9 next_to_clean 8 (in hw 9) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=10 next_to_clean 9 (in hw 10) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=11 next_to_clean 10 (in hw 11) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=12 next_to_clean 11 (in hw 12) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=13 next_to_clean 12 (in hw 13) next_to_use 511 (in hw 15)
enetc_clean_rx_ring: rx_frm_cnt=1 cleaned_cnt=14 next_to_clean 13 (in hw 14) next_to_use 511 (in hw 15)

20 packets transmitted, 12 packets received, 40% packet loss

And there it dies. No enetc_refill_rx_ring (because cleaned_cnt must be equal
to 15 for that to happen), no nothing. The hardware enters the condition where
the producer (14) + 1 is equal to the consumer (15) index, which makes it
believe it has no more free buffers to put packets in, so it starts discarding
them:

ip netns exec ns0 ethtool -S eno0 | grep -v ': 0'
NIC statistics:
     Rx ring  0 discarded frames: 8

Summarized, if the interface receives between 16 and 32 (mod 512) frames
and then there is a link flap, then the port will eventually die with no
way to recover. If it receives less than 16 (mod 512) frames, then the
initial NAPI poll [ before the link flap ] will not update the consumer
index in hardware (it will remain zero) which will be ok when the buffers
are later reinitialized. If more than 32 (mod 512) frames are received,
the initial NAPI poll has the chance to refill the ring twice, updating
the consumer index to at least 32. So after the link flap, the consumer
index is still wrong, but the post-flap NAPI poll gets a chance to
refill the ring once (because it passes through cleaned_cnt=15) and
makes the consumer index be again back in sync with next_to_use.

The solution to this problem is actually simple, we just need to write
next_to_use into the hardware consumer index at enetc_open time, which
always brings it back in sync after an initial buffer seeding process.

The simpler thing would be to put the write to the consumer index into
enetc_refill_rx_ring directly, but there are issues with the MDIO
locking: in the NAPI poll code we have the enetc_lock_mdio() taken from
top-level and we use the unlocked enetc_wr_reg_hot, whereas in
enetc_open, the enetc_lock_mdio() is not taken at the top level, but
instead by each individual enetc_wr_reg, so we are forced to put an
additional enetc_wr_reg in enetc_setup_rxbdr. Better organization of
the code is left as a refactoring exercise.

Fixes: d4fd0404 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 5317365401119e88268d61691d298704ca7286c4
bugzilla: 51348

--------------------------------

commit 96a5223b upstream.

The Station Interface Receive Interrupt Detect Register (SIRXIDR)
contains a 16-bit wide mask of 'interrupt detected' events for each ring
associated with a port. Bit i is write-1-to-clean for RX ring i.

I have no explanation whatsoever how this line of code came to be
inserted in the blamed commit. I checked the downstream versions of that
patch and none of them have it.

The somewhat comical aspect of it is that we're writing a binary number
to the SIRXIDR register, which is derived from enetc_bd_unused(rx_ring).
Since the RX rings have 512 buffer descriptors, we end up writing 511 to
this register, which is 0x1ff, so we are effectively clearing the
'interrupt detected' event for rings 0-8.

This register is not what is used for interrupt handling though - it
only provides a summary for the entire SI. The hardware provides one
separate Interrupt Detect Register per RX ring, which auto-clears upon
read. So there doesn't seem to be any adverse effect caused by this
bogus write.

There is, however, one reason why this should be handled as a bugfix:
next_to_clean _should_ be committed to hardware, just not to that
register, and this was obscuring the fact that it wasn't. This is fixed
in the next patch, and removing the bogus line now allows the fix patch
to be backported beyond that point.

Fixes: fd5736bf ("enetc: Workaround for MDIO register access issue")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 63876df5615edfe94291409eb862f4570e2f4ffc
bugzilla: 51348

--------------------------------

commit c76a9721 upstream.

The ENETC port 0 MAC supports in-band status signaling coming from a PHY
when operating in RGMII mode, and this feature is enabled by default.

It has been reported that RGMII is broken in fixed-link, and that is not
surprising considering the fact that no PHY is attached to the MAC in
that case, but a switch.

This brings us to the topic of the patch: the enetc driver should have
not enabled the optional in-band status signaling for RGMII unconditionally,
but should have forced the speed and duplex to what was resolved by
phylink.

Note that phylink does not accept the RGMII modes as valid for in-band
signaling, and these operate a bit differently than 1000base-x and SGMII
(notably there is no clause 37 state machine so no ACK required from the
MAC, instead the PHY sends extra code words on RXD[3:0] whenever it is
not transmitting something else, so it should be safe to leave a PHY
with this option unconditionally enabled even if we ignore it). The spec
talks about this here:
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/138/RGMIIv1_5F00_3.pdf

Fixes: 71b77a7a ("enetc: Migrate to PHYLINK and PCS_LYNX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 5732688c8411b1d29a3676819c279236b0a0ec5b
bugzilla: 51348

--------------------------------

commit a74dbce9 upstream.

Quoting from the blamed commit:

    In promiscuous mode, it is more intuitive that all traffic is received,
    including VLAN tagged traffic. It appears that it is necessary to set
    the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
    also temporarily enabled. On exit from promiscuous mode, the setting
    made by ethtool is restored.

Intuitive or not, there isn't any definition issued by a standards body
which says that promiscuity has anything to do with VLAN filtering - it
only has to do with accepting packets regardless of destination MAC address.

In fact people are already trying to use this misunderstanding/bug of
the enetc driver as a justification to transform promiscuity into
something it never was about: accepting every packet (maybe that would
be the "rx-all" netdev feature?):
https://lore.kernel.org/netdev/20201110153958.ci5ekor3o2ekg3ky@ipetronik.com/

This is relevant because there are use cases in the kernel (such as
tc-flower rules with the protocol 802.1Q and a vlan_id key) which do not
(yet) use the vlan_vid_add API to be compatible with VLAN-filtering NICs
such as enetc, so for those, disabling rx-vlan-filter is currently the
only right solution to make these setups work:
https://lore.kernel.org/netdev/CA+h21hoxwRdhq4y+w8Kwgm74d4cA0xLeiHTrmT-VpSaM7obhkg@mail.gmail.com/
The blamed patch has unintentionally introduced one more way for this to
work, which is to enable IFF_PROMISC, however this is non-portable
because port promiscuity is not meant to disable VLAN filtering.
Therefore, it could invite people to write broken scripts for enetc, and
then wonder why they are broken when migrating to other drivers that
don't handle promiscuity in the same way.

Fixes: 7070eea5 ("enetc: permit configuration of rx-vlan-filter with ethtool")
Cc: Markus Blöchl <Markus.Bloechl@ipetronik.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit d56e3f8d289bdc70378f84efab166ad38022532e
bugzilla: 51348

--------------------------------

commit 827b6fd0 upstream.

When the enetc ports have rx-vlan-offload enabled, they report a TPID of
ETH_P_8021Q regardless of what was actually in the packet. When
rx-vlan-offload is disabled, packets have the proper TPID. Fix this
inconsistency by finishing the TODO left in the code.

Fixes: d4fd0404 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit bf9c564716a13dde6a990d3b02c27cd6e39608bf
bugzilla: 51348

--------------------------------

commit 6d36ecdb upstream.

The workaround for the ENETC MDIO erratum caused a performance
degradation of 82 Kpps (seen with IP forwarding of two 1Gbps streams of
64B packets). This is due to excessive locking and unlocking in the fast
path, which can be avoided.

By taking the MDIO read-side lock only once per NAPI poll cycle, we are
able to regain 54 Kpps (65%) of the performance hit. The rest of the
performance degradation comes from the TX data path, but unfortunately
it doesn't look like we can optimize that away easily, even with
netdev_xmit_more(), there just isn't any skb batching done, to help with
taking the MDIO lock less often than once per packet.

We need to change the register accessor type for enetc_get_tx_tstamp,
because it now runs under the enetc_lock_mdio as per the new call path
detailed below:

enetc_msix
-> napi_schedule
   -> enetc_poll
      -> enetc_lock_mdio
      -> enetc_clean_tx_ring
         -> enetc_get_tx_tstamp
      -> enetc_clean_rx_ring
      -> enetc_unlock_mdio

Fixes: fd5736bf ("enetc: Workaround for MDIO register access issue")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit dfaf418dfff819aaa5e6a945bb8efd38d53b6eb9
bugzilla: 51348

--------------------------------

commit c646d10d upstream.

After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:

enetc_pf_probe
-> enetc_alloc_si_resources
   -> enetc_configure_si
      -> enetc_setup_default_rss_table

is overwritten later in:

enetc_pf_probe
-> enetc_init_port_rss_memory

which zero-initializes the entire port RSS table in order to avoid ECC errors.

The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.

The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.

Fixes: 07bf34a5 ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 4ea379733555d652acadb05112a3365e5059f6f4
bugzilla: 51348

--------------------------------

commit 8c91bc3d upstream.

According  to  the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver.  Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...

Fixes: 86a74ff2 ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: NSergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 1e343b2e7b9678f199df9693a3548e9a4ab98488
bugzilla: 51348

--------------------------------

commit 67eb2114 upstream.

The last change to ibmvnic_set_mac(), 8fc3672a, meant to prevent
users from setting an invalid MAC address on an ibmvnic interface
that has not been brought up yet. The change also prevented the
requested MAC address from being stored by the adapter object for an
ibmvnic interface when the state of the ibmvnic interface is
VNIC_PROBED - that is after probing has finished but before the
ibmvnic interface is brought up. The MAC address stored by the
adapter object is used and sent to the hypervisor for checking when
an ibmvnic interface is brought up.

The ibmvnic driver ignoring the requested MAC address when in
VNIC_PROBED state caused LACP bonds (bonds in 802.3ad mode) with more
than one slave to malfunction. The bonding code must be able to
change the MAC address of its slaves before they are brought up
during enslaving. The inability of kernels with 8fc3672a to set
the MAC addresses of bonding slaves is observable in the output of
"ip address show". The MAC addresses of the slaves are the same as
the MAC address of the bond on a working system whereas the slaves
retain their original MAC addresses on a system with a malfunctioning
LACP bond.

Fixes: 8fc3672a ("ibmvnic: fix ibmvnic_set_mac")
Signed-off-by: NJiri Wiesner <jwiesner@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit 57ac75f8d241b3d13b77d223214be025f18df8a1
bugzilla: 51348

--------------------------------

commit 6881b07f upstream.

GCC 7.5 reports:
../drivers/net/ethernet/ibm/ibmvnic.c: In function 'ibmvnic_reset_init':
../drivers/net/ethernet/ibm/ibmvnic.c:5373:51: warning: 'old_num_tx_queues' may be used uninitialized in this function [-Wmaybe-uninitialized]
../drivers/net/ethernet/ibm/ibmvnic.c:5373:6: warning: 'old_num_rx_queues' may be used uninitialized in this function [-Wmaybe-uninitialized]

The variable is initialized only if(reset) and used only if(reset &&
something) so this is a false positive. However, there is no reason to
not initialize the variables unconditionally avoiding the warning.

Fixes: 635e442f ("ibmvnic: merge ibmvnic_reset_init and ibmvnic_init")
Signed-off-by: NMichal Suchanek <msuchanek@suse.de>
Reviewed-by: NSukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.24
commit a0df424a863aa6a2e8bd57ef5e0928da5d5b797f
bugzilla: 51348

--------------------------------

commit a4dcfbc4 upstream.

netif_device_attach() will unpause the queues so we can't call
it before __alx_open(). This went undetected until
commit b0999223 ("alx: add ability to allocate and free
alx_napi structures") but now if stack tries to xmit immediately
on resume before __alx_open() we'll crash on the NAPI being null:

 BUG: kernel NULL pointer dereference, address: 0000000000000198
 CPU: 0 PID: 12 Comm: ksoftirqd/0 Tainted: G           OE 5.10.0-3-amd64 #1 Debian 5.10.13-1
 Hardware name: Gigabyte Technology Co., Ltd. To be filled by O.E.M./H77-D3H, BIOS F15 11/14/2013
 RIP: 0010:alx_start_xmit+0x34/0x650 [alx]
 Code: 41 56 41 55 41 54 55 53 48 83 ec 20 0f b7 57 7c 8b 8e b0
0b 00 00 39 ca 72 06 89 d0 31 d2 f7 f1 89 d2 48 8b 84 df
 RSP: 0018:ffffb09240083d28 EFLAGS: 00010297
 RAX: 0000000000000000 RBX: ffffa04d80ae7800 RCX: 0000000000000004
 RDX: 0000000000000000 RSI: ffffa04d80afa000 RDI: ffffa04e92e92a00
 RBP: 0000000000000042 R08: 0000000000000100 R09: ffffa04ea3146700
 R10: 0000000000000014 R11: 0000000000000000 R12: ffffa04e92e92100
 R13: 0000000000000001 R14: ffffa04e92e92a00 R15: ffffa04e92e92a00
 FS:  0000000000000000(0000) GS:ffffa0508f600000(0000) knlGS:0000000000000000
 i915 0000:00:02.0: vblank wait timed out on crtc 0
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 0000000000000198 CR3: 000000004460a001 CR4: 00000000001706f0
 Call Trace:
  dev_hard_start_xmit+0xc7/0x1e0
  sch_direct_xmit+0x10f/0x310

Cc: <stable@vger.kernel.org> # 4.9+
Fixes: bc2bebe8 ("alx: remove WoL support")
Reported-by: NZbynek Michl <zbynek.michl@gmail.com>
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=983595Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Tested-by: NZbynek Michl <zbynek.michl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.22
commit b31a9f0c366d7bf2d6d696c99919e603639a9f0a
bugzilla: 50796

--------------------------------

commit d2a04370 upstream.

Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.

Fixes: e80bd76f ("r8169: work around power-saving bug on some chip versions")
Reported-by: NArmin Wolf <W_Armin@gmx.de>
Tested-by: NArmin Wolf <W_Armin@gmx.de>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: N  Weilong Chen <chenweilong@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.21
commit a31cb3072d11411e3fdf2d93ab3daded5b69d18b
bugzilla: 50609

--------------------------------

commit 04b385f3 upstream.

2 bytes of the MTU are reserved for Atheros DSA tag, but DSA core
has already handled that since commit dc0fe7d4.
Remove the unnecessary reservation.

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NOleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210218034514.3421-1-dqfext@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit 8d1d23a8472604aa6948c8a7fd93cd45a5cf287a
bugzilla: 50608

--------------------------------

[ Upstream commit 6cf73913 ]

Josef reported [0] that using jumbo packets fails on RTL8168e.
Aligning the values for register MaxTxPacketSize with the
vendor driver fixes the problem.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=211827

Fixes: d58d46b5 ("r8169: jumbo fixes.")
Reported-by: NJosef Oškera <joskera@redhat.com>
Tested-by: NJosef Oškera <joskera@redhat.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b15ddef7-0d50-4320-18f4-6a3f86fbfd3e@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit 1c0058472166c1d92cd9c52442eb7ef09fbd1784
bugzilla: 50608

--------------------------------

[ Upstream commit 8eb65fda ]

mlx4_do_mirror_rule() forgets to call mlx4_free_cmd_mailbox() to
free the memory region allocated by mlx4_alloc_cmd_mailbox() before
an exit.
Add the missed call to fix it.

Fixes: 78efed27 ("net/mlx4_core: Support mirroring VF DMFS rules on both ports")
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Reviewed-by: NTariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210221143559.390277-1-hslester96@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit ba817c1766086d8eb0502299a245a3c1547f655a
bugzilla: 50608

--------------------------------

[ Upstream commit 24877687 ]

When link speed is not 100 Mbps, port transmit rate and speed divider
are set to 8 and 1000000 respectively. These values are incorrect for
CBS idleslope and sendslope HW values calculation if the link speed is
not 1 Gbps.

This patch adds switch statement to set the values of port transmit rate
and speed divider for 10 Gbps, 5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps.
Note that CBS is not supported at 10 Mbps.

Fixes: bc41a668 ("net: stmmac: tc: Remove the speed dependency")
Fixes: 1f705bc6 ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: NSong, Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/r/1613655653-11755-1-git-send-email-yoong.siang.song@intel.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit dd2d203f02ff2eb4d1f75ae818b18788cdcf19f9
bugzilla: 50608

--------------------------------

[ Upstream commit 0393e46a ]

It was possible to have Rx queues that were not available for use
by RSS. This would happen when increasing the number of Rx queues
while there was a user defined RSS LUT.

Always update the number of available RSS queues when changing the
number of Rx queues.

Fixes: 87324e74 ("ice: Implement ethtool ops for channels")
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit 70bcfea70f12a72b67e868f474e9512c5ec6ae21
bugzilla: 50608

--------------------------------

[ Upstream commit 0d4907f6 ]

DCBX_CAP bits were not being adjusted when switching
between SW and FW controlled LLDP.

Adjust bits to correctly indicate which mode the
LLDP logic is in.

Fixes: b94b013e ("ice: Implement DCBNL support")
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit 09a2fee495467a641312837d495e99f0f40d12a7
bugzilla: 50608

--------------------------------

[ Upstream commit a6aa7c8f ]

Currently if an AVF driver doesn't account for the possibility of a
port VLAN when determining its max packet size then packets at MTU will
be dropped. It is not the VF driver's responsibility to account for a
port VLAN so fix this. To fix this, do the following:

1. Add a function that determines the max packet size a VF is allowed by
   using the port's max packet size and whether the VF is in a port
   VLAN. If a port VLAN is configured then a VF's max packet size will
   always be the port's max packet size minus VLAN_HLEN. Otherwise it
   will be the port's max packet size.

2. Use this function to verify the max packet size from the VF.

3. If there is a port VLAN configured then add 4 bytes (VLAN_HLEN) to
   the VF's max packet size configuration.

Also, the VIRTCHNL_OP_GET_VF_RESOURCES message provides the capability
to communicate a VF's max packet size. Use the new function for this
purpose.

Fixes: 1071a835 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit 4bee367264f126c47bfe19b0a8c58f543472ef6b
bugzilla: 50608

--------------------------------

[ Upstream commit 7dcf7aa0 ]

In the driver currently, we are reporting max number of TCs
to the DCBNL callback as a kernel define set to 8.  This is
preventing userspace applications performing DCBx to correctly
down map the TCs from requested to actual values.

Report the actual max TC value to userspace from the capability
struct.

Fixes: b94b013e ("ice: Implement DCBNL support")
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-5.10.20
commit dae49384d0d7695540e2d75168f323cef1384810
bugzilla: 50608

--------------------------------

[ Upstream commit 3a2eb515 ]

This code does not allocate enough memory for the NUL terminator so it
ends up putting it one character beyond the end of the buffer.

Fixes: 8756828a ("octeontx2-af: Add NPA aura and pool contexts to debugfs")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NChen Jun <chenjun102@huawei.com>
Acked-by: NXie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>