dm9000: Add regulator and reset support to dm9000

In boards, the dm9000 chip's power and reset can be controlled by gpio.

It makes sense to add them to the dm9000 driver and let dt be used to
enable power and reset the phy.
Signed-off-by: NZubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/davicom-dm9000.txt

@@ -11,6 +11,8 @@ Required properties:
 Optional properties:
 - davicom,no-eeprom : Configuration EEPROM is not available
 - davicom,ext-phy : Use external PHY
+- reset-gpios : phandle of gpio that will be used to reset chip during probe
+- vcc-supply : phandle of regulator that will be used to enable power to chip
 
 Example:
 
@@ -21,4 +23,6 @@ Example:
 		interrupts = <7 4>;
 		local-mac-address = [00 00 de ad be ef];
 		davicom,no-eeprom;
+		reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&eth0_power>;
 	};

drivers/net/ethernet/davicom/dm9000.c

@@ -36,6 +36,9 @@
 #include <linux/platform_device.h>
 #include <linux/irq.h>
 #include <linux/slab.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
+#include <linux/of_gpio.h>
 
 #include <asm/delay.h>
 #include <asm/irq.h>
@@ -1426,11 +1429,48 @@ dm9000_probe(struct platform_device *pdev)
 	struct dm9000_plat_data *pdata = dev_get_platdata(&pdev->dev);
 	struct board_info *db;	/* Point a board information structure */
 	struct net_device *ndev;
+	struct device *dev = &pdev->dev;
 	const unsigned char *mac_src;
 	int ret = 0;
 	int iosize;
 	int i;
 	u32 id_val;
+	int reset_gpios;
+	enum of_gpio_flags flags;
+	struct regulator *power;
+
+	power = devm_regulator_get(dev, "vcc");
+	if (IS_ERR(power)) {
+		if (PTR_ERR(power) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		dev_dbg(dev, "no regulator provided\n");
+	} else {
+		ret = regulator_enable(power);
+		if (ret != 0) {
+			dev_err(dev,
+				"Failed to enable power regulator: %d\n", ret);
+			return ret;
+		}
+		dev_dbg(dev, "regulator enabled\n");
+	}
+
+	reset_gpios = of_get_named_gpio_flags(dev->of_node, "reset-gpios", 0,
+					      &flags);
+	if (gpio_is_valid(reset_gpios)) {
+		ret = devm_gpio_request_one(dev, reset_gpios, flags,
+					    "dm9000_reset");
+		if (ret) {
+			dev_err(dev, "failed to request reset gpio %d: %d\n",
+				reset_gpios, ret);
+			return -ENODEV;
+		}
+
+		/* According to manual PWRST# Low Period Min 1ms */
+		msleep(2);
+		gpio_set_value(reset_gpios, 1);
+		/* Needs 3ms to read eeprom when PWRST is deasserted */
+		msleep(4);
+	}
 
 	if (!pdata) {
 		pdata = dm9000_parse_dt(&pdev->dev);