This patch add IGNPAR flag handling for the driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

sccnxp_timer() is triggered only by timer, so there are no need to
check for timer_pending().
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch disables the receiver ready interrupt for imx_stop_rx.
It reduces the interrupt numbers when the uart is going to close
or suspend.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA wait queue makes the code very complicated:
  For RX, the @->stop_rx hook does not really stop the RX;
  For TX, the @->stop_tx hook does not really stop the TX.

The above make the imx_shutdown has to wait the RX/TX DMA to be finished.

In order to make code more simple, this patch removes the DMA wait queue.
By calling the dmaengine_terminate_all, this patch makes the RX stops
immediately after we call the @->stop_rx hook, so does the TX.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the imx_startup(), we will reset the uart port which will reset all
the FIFOs, including the URXD.

So the code to clear the RX FIFO is redundant. Just remove it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Current code resets the uart port only when it supports the irda mode.
In actually, we also need to reset the uart port in the non-irda mode.
A hang was caught in the following case:

    UART A transmits data to the other end. But the transmission maybe
    terminated. In some corner case, the TX FIFO maybe not empty.

The kernel will hang at the imx_set_termios():
	............................................................
	while (!(readl(sport->port.membase + USR2) & USR2_TXDC))
		barrier();
	............................................................

This patch resets the uart port all the time in the imx_startup().
And fix the hang.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for Advantech PCM-3614I/PCM-3618I serial expansion cards

Advantech makes a variety of serial port expansion cards, including the
PCM-3614 and PCM-3618
(http://www.advantech.com/products/1-2JKLU5/PCM-3618/mod_5DF8DE5A-6B49-4429-BB2F-CB35FE1D168D.aspx).
They have a driver available which was forked from the kernel driver
ages ago and has not been maintained in quite some time, available at
http://support.advantech.com.tw/Support/DownloadSRDetail_New.aspx?SR_ID=1-1W8FZ5&Doc_Source=Download
Their driver added several features to aid in communications at higher
baud rates, but at normal serial port speeds, the standard 8250_pci
driver functions just fine. This patch adds the necessary PCI IDs to
recognize this card.

See bug 75681 (https://bugzilla.kernel.org/show_bug.cgi?id=75681)
Signed-off-by: NThomee Wright <TWright@TMCDesign.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:

ADNIMP: Autobaud Detection Not Improved-. Disables new features of
	autobaud detection (See Baud Rate Automatic Detection
	Protocol, for more details).

	0 Autobaud detection new features selected
	1 Keep old autobaud detection mechanism

The "new features" mechanism occasionally cause the receiver to get out of sync
and continuously produce received characters of '\xff'.

In order to reproduce the problem:

$ stty -F /dev/ttymxc0 19200

- Change the terminal baudrate to 19200

- Type in the console and it should look good

- Change the terminal baudrate back to 115200

- Type 'b' in the console, then a stream of garbage characters is seen.

Also rename the bit definition as per the reference manual.

Tested on mx6q, mx6dl, mx6solo and mx53.

Based on a patch from Eric Nelson for U-boot.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NEric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:

03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
	Subsystem: Device 4348:5053
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at cf00 [size=8]
	Region 1: I/O ports at ce00 [size=8]
	Kernel driver in use: parport_serial
	Kernel modules: 8250_pci, parport_serial

This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.

Proper entries are added to parport_serial, to support the device parallel
and serial ports.

Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing specification of efm32_uart_exit as module_exit.

This fixes the following compilation warning:

  drivers/tty/serial/efm32-uart.c:840:123: warning: ‘efm32_uart_exit’ defined but not used [-Wunused-function]
Signed-off-by: NVincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add format and argument checking and fix misuses in the dbg macro.

Add __printf
Use %pR for resource
Add #include guard to samsung.h
Move static functions from .h to .c
Use vscnprintf instead of length unguarded vsprintf
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't activate the TX Space available IRQ on startup, or a simple
$ cat /dev/ttyHSU0
will cause an endless amount of IRQs, as there is always space in
the TX FIFO available if no data is going to be sent.

Also correct comments for IRQ names (RX and TX swapped).
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On my test platform (B2020/STiH416) the serial port issues bad characters
during the initial message avalanche as the console comes up. The problem
also occurs when dense(ish) I/O is done using the polled I/O interface.

The problem is fixed for me by using the FIFO half-empty bit rather than
FIFO full bit. Note that using the half-empty bit causes the FIFO to be
managed in a similar way to interrupt based I/O (i.e. where the hardware
gets best test coverage).

Running the FIFO half full will have no impact (good or bad) on console
performance. The UART will still remain fully saturated and the busy-wait
until the FIFO is empty in asc_console_write() will complete at the same
time.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Xilinx MDM (Microblaze Debug Module) also contains
uart interface via JTAG which is compatible with
uartlite driver. This interface is really slow
that's why timeout is setup to 1s.

Make this time delay not to be cpu speed dependent.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NPeter Korsgaard <peter@korsgaard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If NO_DMA=y:

drivers/built-in.o: In function `lpuart_dma_rx_free':
fsl_lpuart.c:(.text+0x7da28): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_tx_free':
fsl_lpuart.c:(.text+0x7da60): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_rx':
fsl_lpuart.c:(.text+0x7dab8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_dma_tx':
fsl_lpuart.c:(.text+0x7db7e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_copy_rx_to_tty':
fsl_lpuart.c:(.text+0x7dcd4): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb78b811 provide a workaround for
kernel panic, but bring potential deadlock risk. that is in
sirfsoc_rx_tmo_process_tl while enter into sirfsoc_uart_pio_rx_chars
cpu hold uart_port->lock, if uart interrupt comes cpu enter into
sirfsoc_uart_isr and deadlock occurs in getting uart_port->lock.

the patch replace spin_lock version to spin_lock_irq* version to avoid
spinlock dead lock issue. let function tty_flip_buffer_push in tasklet
outof spin_lock_irq* protect area to avoid add the pair of spin_lock and
spin_unlock for tty_flip_buffer_push.
BTW drop self defined unused spinlock protect of tx_lock/rx_lock.

56274.220464] BUG: spinlock lockup suspected on CPU#0, swapper/0/0
[56274.223648]  lock: 0xc05d9db0, .magic: dead4ead, .owner: swapper/0/0,
	.owner_cpu: 0
	[56274.231278] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G
	O 3.10.35 #1
	[56274.238241] [<c0015530>] (unwind_backtrace+0x0/0xf4) from
	[<c00120d8>] (show_stack+0x10/0x14)
	[56274.246742] [<c00120d8>] (show_stack+0x10/0x14) from
	[<c01b11b0>] (do_raw_spin_lock+0x110/0x184)
	[56274.255501] [<c01b11b0>] (do_raw_spin_lock+0x110/0x184) from
	[<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c)
	[56274.264874] [<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c) from
	[<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
	[56274.274758] [<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
	from [<c00758f4>] (handle_irq_event+0x3c/0x5c)
	[56274.284561] [<c00758f4>] (handle_irq_event+0x3c/0x5c) from
	[<c0077fa0>] (handle_level_irq+0x98/0xfc)
	[56274.293670] [<c0077fa0>] (handle_level_irq+0x98/0xfc) from
	[<c0074f44>] (generic_handle_irq+0x2c/0x3c)
	[56274.302952] [<c0074f44>] (generic_handle_irq+0x2c/0x3c) from
	[<c000ef80>] (handle_IRQ+0x40/0x90)
	[56274.311706] [<c000ef80>] (handle_IRQ+0x40/0x90) from
	[<c000dc80>] (__irq_svc+0x40/0x70)
	[56274.319697] [<c000dc80>] (__irq_svc+0x40/0x70) from
	[<c038113c>] (_raw_spin_unlock_irqrestore+0x10/0x48)
	[56274.329158] [<c038113c>]
	(_raw_spin_unlock_irqrestore+0x10/0x48) from [<c0200034>]
	(tty_port_tty_get+0x58/0x90)
	[56274.339213] [<c0200034>] (tty_port_tty_get+0x58/0x90) from
	[<c0212008>] (sirfsoc_uart_pio_rx_chars+0x1c/0xc8)
	[56274.349097] [<c0212008>]
	(sirfsoc_uart_pio_rx_chars+0x1c/0xc8) from [<c0212ef8>]
	(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc)
	[56274.359853] [<c0212ef8>]
	(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc) from [<c0027c04>]
	(tasklet_action+0x84/0x114)
	[56274.369739] [<c0027c04>] (tasklet_action+0x84/0x114) from
	[<c0027db4>] (__do_softirq+0x120/0x200)
	[56274.378585] [<c0027db4>] (__do_softirq+0x120/0x200) from
	[<c0027f44>] (do_softirq+0x54/0x5c)
	[56274.386998] [<c0027f44>] (do_softirq+0x54/0x5c) from
	[<c00281ec>] (irq_exit+0x9c/0xd0)
	[56274.394899] [<c00281ec>] (irq_exit+0x9c/0xd0) from
	[<c000ef84>] (handle_IRQ+0x44/0x90)
	[56274.402790] [<c000ef84>] (handle_IRQ+0x44/0x90) from
	[<c000dc80>] (__irq_svc+0x40/0x70)
	[56274.410774] [<c000dc80>] (__irq_svc+0x40/0x70) from
	[<c0288af4>] (cpuidle_enter_state+0x50/0xe0)
	[56274.419532] [<c0288af4>] (cpuidle_enter_state+0x50/0xe0) from
	[<c0288c34>] (cpuidle_idle_call+0xb0/0x148)
	[56274.429080] [<c0288c34>] (cpuidle_idle_call+0xb0/0x148) from
	[<c000f3ac>] (arch_cpu_idle+0x8/0x38)
	[56274.438016] [<c000f3ac>] (arch_cpu_idle+0x8/0x38) from
	[<c0059344>] (cpu_startup_entry+0xfc/0x140)
	[56274.446956] [<c0059344>] (cpu_startup_entry+0xfc/0x140) from
	[<c04a3a54>] (start_kernel+0x2d8/0x2e4)
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All SiRFSoC UART registers are in 32-bits. If we use writeb for
TXFIFO, actually all of 32-bits are still written, for TXTIFO,
only low 8-bits are valid, so in prima2&atlas6, this causes no
problem.
But in the new atlas7, using writeb to write UART registers will
cause an imprecise data abort as HW does check the "wrong" writeb.
So move to writel and this also makes the code consistent with
sirfsoc_uart_pio_tx_chars() in which we use writel.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Two new drivers have been added since 3.14, the MEN 16z135 uart, and
the ARM semihosting console. Both are missing an explicit 'select
SERIAL_CORE', which can leads build errors when no other driver
selects the core, as found during ARM randconfig testing.
In case of the ARM semihosting console, we also have to select
SERIAL_CORE_CONSOLE.

This adds the missing 'select' statements.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes the warnings:

   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_rx':
>> drivers/tty/serial/sc16is7xx.c:548:1: warning: 'sc16is7xx_handle_rx' uses dynamic stack allocation [enabled by default]
   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_tx':
>> drivers/tty/serial/sc16is7xx.c:589:1: warning: 'sc16is7xx_handle_tx' uses dynamic stack allocation [enabled by default]
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/sc16is7xx.c:1060:12: warning: 'sc16is7xx_probe' defined but not used [-Wunused-function]
 static int sc16is7xx_probe(struct device *dev,
            ^
drivers/tty/serial/sc16is7xx.c:1176:12: warning: 'sc16is7xx_remove' defined but not used [-Wunused-function]
 static int sc16is7xx_remove(struct device *dev)
            ^
drivers/tty/serial/sc16is7xx.c:1215:29: warning: 'regcfg' defined but not used [-Wunused-variable]
 static struct regmap_config regcfg = {
                             ^

Fixed these warnings by removing the `#ifdef CONFIG_REGMAP_I2C' around their
calls as this driver selects REGMAP_I2C in Kconfig. This part of driver just
didn't compile at all when REGMAP_I2C configured as module (CONFIG_REGMAP_I2C
is not defined, just CONFIG_REGMAP_I2C_MODULE).
Signed-off-by: NJan Moskyto Matejka <mq@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pch_uart driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 9aac5887 (tty/serial: add generic serial earlycon) moved
console option parsing from 8250_early.c and converted to kstrto*
functions from simple_strtoul along the way. However, kstrto* functions
are not equivalent in that they do not allow non-convertible characters
at the end such as "115200n8". Fix this by changing back to
simple_strtoul and ignore what checkpatch.pl says.
Reported-by: NYinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d2fd6810 (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:

arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c

Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: NYinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix by including linux/uaccess.h:

   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_ioctl':
>> drivers/tty/serial/sc16is7xx.c:861:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/sc16is7xx.c:867:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The SC16IS7xx is a slave I2C-bus/SPI interface to a single-channel
high performance UART. The SC16IS7xx's internal register set is
backward-compatible with the widely used and widely popular 16C450.

The SC16IS7xx also provides additional advanced features such as
auto hardware and software flow control, automatic RS-485 support, and
software reset.
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit fcbee4d4.

It wasn't quite ready to go in yet, sorry about that.

Cc: Simon Horman <horms@verge.net.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add earlycon support for the arm/arm64 semihosting debug serial
interface. This allows enabling a debug console when early_params are
processed. This is based on the arm64 earlyprintk smh support and is
intended to replace it.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add earlycon support for the pl011 serial port. This allows enabling
the pl011 for console when early_params are processed. This is based
on the arm64 earlyprintk support and is intended to replace it.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With the generic earlycon infrastructure in place, convert the 8250
early console to use it.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This introduces generic earlycon infrastructure for serial devices
based on the 8250 earlycon. This allows for supporting earlycon option
with other serial devices. The earlycon output is enabled at the time
early_params are processed.

Only architectures that have fixmap support or have functional ioremap
when early_params are processed are supported. This is the same
restriction that the 8250 driver had.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In preparation to support FIX_EARLYCON_MEM on other arches, make the
option per arch.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add driver for MEN's 16z135 High Speed UART.

The 16z135 is a memory mapped UART Core on an MCB FPGA and has 1024 byte
deep FIFO buffers for the RX and TX path. It also has configurable FIFO
fill level IRQs and data copied to and from the hardware has to be
acknowledged.
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: NAlan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Zynq's UART is Cadence IP. Make this visible in the prompt in kconfig
and additional comments in the driver.
This also renames functions and symbols, as far as possible without
breaking user space API, to reflect the Cadence origin. This is achieved
through simple search and replace:
 - s/XUARTPS/CDNS_UART/g
 - s/xuartps/cdns_uart/g
The only exceptions are PORT_XUARTPS and the driver name, which stay as is,
due to their exposure to user space. As well as the - no legacy -
compatibility string 'xlnx,xuartps'
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A comment states, that, according to the data sheet, to enable
interrupts the disable register should be written, but the enable
register could be left untouched. And it suspsects a HW bug requiring
to write both.
Reviewing the data sheet, these statements seem wrong. Just as one would
expect. Writing to the enable/disable register enables/disables
interrupts.
Hence the misleading comment and needless write to the disable register
are removed from the enable sequence.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A lot of read-modify-write sequences used a one-line statement which
nests a readl() within a writel(). Convert this into code sequences that
make the three steps more obvious.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Print a warning if the clock notifier rejects a clock frequency change
to facilitate debugging (see:
http://thread.gmane.org/gmane.linux.ports.arm.kernel/304329/focus=304379)
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is all white space and comment clean up. Mostly reformatting
comments.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Register port numbers according to order in DT aliases.
If aliases are not defined, order in DT is used.
If aliases are defined, register port id based
on that.
This patch ensures proper ttyPS0/1 assignment.

[soren]: Combined integer declarations in probe(), removed warning message
if no alias is found.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No functional changes.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>