This patch add IGNPAR flag handling for the driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

sccnxp_timer() is triggered only by timer, so there are no need to
check for timer_pending().
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch disables the receiver ready interrupt for imx_stop_rx.
It reduces the interrupt numbers when the uart is going to close
or suspend.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA wait queue makes the code very complicated:
  For RX, the @->stop_rx hook does not really stop the RX;
  For TX, the @->stop_tx hook does not really stop the TX.

The above make the imx_shutdown has to wait the RX/TX DMA to be finished.

In order to make code more simple, this patch removes the DMA wait queue.
By calling the dmaengine_terminate_all, this patch makes the RX stops
immediately after we call the @->stop_rx hook, so does the TX.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In the imx_startup(), we will reset the uart port which will reset all
the FIFOs, including the URXD.

So the code to clear the RX FIFO is redundant. Just remove it.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Current code resets the uart port only when it supports the irda mode.
In actually, we also need to reset the uart port in the non-irda mode.
A hang was caught in the following case:

    UART A transmits data to the other end. But the transmission maybe
    terminated. In some corner case, the TX FIFO maybe not empty.

The kernel will hang at the imx_set_termios():
	............................................................
	while (!(readl(sport->port.membase + USR2) & USR2_TXDC))
		barrier();
	............................................................

This patch resets the uart port all the time in the imx_startup().
And fix the hang.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for Advantech PCM-3614I/PCM-3618I serial expansion cards

Advantech makes a variety of serial port expansion cards, including the
PCM-3614 and PCM-3618
(http://www.advantech.com/products/1-2JKLU5/PCM-3618/mod_5DF8DE5A-6B49-4429-BB2F-CB35FE1D168D.aspx).
They have a driver available which was forked from the kernel driver
ages ago and has not been maintained in quite some time, available at
http://support.advantech.com.tw/Support/DownloadSRDetail_New.aspx?SR_ID=1-1W8FZ5&Doc_Source=Download
Their driver added several features to aid in communications at higher
baud rates, but at normal serial port speeds, the standard 8250_pci
driver functions just fine. This patch adds the necessary PCI IDs to
recognize this card.

See bug 75681 (https://bugzilla.kernel.org/show_bug.cgi?id=75681)
Signed-off-by: NThomee Wright <TWright@TMCDesign.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Bit 7 of UCR3 is described in the i.MX reference manuals (with the exception
of i.MX1) as follows:

ADNIMP: Autobaud Detection Not Improved-. Disables new features of
	autobaud detection (See Baud Rate Automatic Detection
	Protocol, for more details).

	0 Autobaud detection new features selected
	1 Keep old autobaud detection mechanism

The "new features" mechanism occasionally cause the receiver to get out of sync
and continuously produce received characters of '\xff'.

In order to reproduce the problem:

$ stty -F /dev/ttymxc0 19200

- Change the terminal baudrate to 19200

- Type in the console and it should look good

- Change the terminal baudrate back to 115200

- Type 'b' in the console, then a stream of garbage characters is seen.

Also rename the bit definition as per the reference manual.

Tested on mx6q, mx6dl, mx6solo and mx53.

Based on a patch from Eric Nelson for U-boot.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Tested-by: NEric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This Multi-IO card has one serial 16550-like and one parallel port connector.
Here's the lspci output, after this commit is applied:

03:07.0 Serial controller: Device 4348:5053 (rev 10) (prog-if 02 [16550])
	Subsystem: Device 4348:5053
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at cf00 [size=8]
	Region 1: I/O ports at ce00 [size=8]
	Kernel driver in use: parport_serial
	Kernel modules: 8250_pci, parport_serial

This commit adds an entry with the device ID to the blacklist declared in
8250_pci to prevent the driver from taking ownership. Also, and as was done
for the 2S/1P variant, add a quirk to skip autodetection and set the correct
type to 16550A clone.

Proper entries are added to parport_serial, to support the device parallel
and serial ports.

Cc: Gianluca Anzolin <gianluca@sottospazio.it>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing specification of efm32_uart_exit as module_exit.

This fixes the following compilation warning:

  drivers/tty/serial/efm32-uart.c:840:123: warning: ‘efm32_uart_exit’ defined but not used [-Wunused-function]
Signed-off-by: NVincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add format and argument checking and fix misuses in the dbg macro.

Add __printf
Use %pR for resource
Add #include guard to samsung.h
Move static functions from .h to .c
Use vscnprintf instead of length unguarded vsprintf
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't activate the TX Space available IRQ on startup, or a simple
$ cat /dev/ttyHSU0
will cause an endless amount of IRQs, as there is always space in
the TX FIFO available if no data is going to be sent.

Also correct comments for IRQ names (RX and TX swapped).
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On my test platform (B2020/STiH416) the serial port issues bad characters
during the initial message avalanche as the console comes up. The problem
also occurs when dense(ish) I/O is done using the polled I/O interface.

The problem is fixed for me by using the FIFO half-empty bit rather than
FIFO full bit. Note that using the half-empty bit causes the FIFO to be
managed in a similar way to interrupt based I/O (i.e. where the hardware
gets best test coverage).

Running the FIFO half full will have no impact (good or bad) on console
performance. The UART will still remain fully saturated and the busy-wait
until the FIFO is empty in asc_console_write() will complete at the same
time.
Signed-off-by: NDaniel Thompson <daniel.thompson@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Acked-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Xilinx MDM (Microblaze Debug Module) also contains
uart interface via JTAG which is compatible with
uartlite driver. This interface is really slow
that's why timeout is setup to 1s.

Make this time delay not to be cpu speed dependent.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NPeter Korsgaard <peter@korsgaard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If NO_DMA=y:

drivers/built-in.o: In function `lpuart_dma_rx_free':
fsl_lpuart.c:(.text+0x7da28): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_tx_free':
fsl_lpuart.c:(.text+0x7da60): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `lpuart_dma_rx':
fsl_lpuart.c:(.text+0x7dab8): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_dma_tx':
fsl_lpuart.c:(.text+0x7db7e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `lpuart_copy_rx_to_tty':
fsl_lpuart.c:(.text+0x7dcd4): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb78b811 provide a workaround for
kernel panic, but bring potential deadlock risk. that is in
sirfsoc_rx_tmo_process_tl while enter into sirfsoc_uart_pio_rx_chars
cpu hold uart_port->lock, if uart interrupt comes cpu enter into
sirfsoc_uart_isr and deadlock occurs in getting uart_port->lock.

the patch replace spin_lock version to spin_lock_irq* version to avoid
spinlock dead lock issue. let function tty_flip_buffer_push in tasklet
outof spin_lock_irq* protect area to avoid add the pair of spin_lock and
spin_unlock for tty_flip_buffer_push.
BTW drop self defined unused spinlock protect of tx_lock/rx_lock.

56274.220464] BUG: spinlock lockup suspected on CPU#0, swapper/0/0
[56274.223648]  lock: 0xc05d9db0, .magic: dead4ead, .owner: swapper/0/0,
	.owner_cpu: 0
	[56274.231278] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G
	O 3.10.35 #1
	[56274.238241] [<c0015530>] (unwind_backtrace+0x0/0xf4) from
	[<c00120d8>] (show_stack+0x10/0x14)
	[56274.246742] [<c00120d8>] (show_stack+0x10/0x14) from
	[<c01b11b0>] (do_raw_spin_lock+0x110/0x184)
	[56274.255501] [<c01b11b0>] (do_raw_spin_lock+0x110/0x184) from
	[<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c)
	[56274.264874] [<c02124c8>] (sirfsoc_uart_isr+0x20/0x42c) from
	[<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
	[56274.274758] [<c0075790>] (handle_irq_event_percpu+0x54/0x17c)
	from [<c00758f4>] (handle_irq_event+0x3c/0x5c)
	[56274.284561] [<c00758f4>] (handle_irq_event+0x3c/0x5c) from
	[<c0077fa0>] (handle_level_irq+0x98/0xfc)
	[56274.293670] [<c0077fa0>] (handle_level_irq+0x98/0xfc) from
	[<c0074f44>] (generic_handle_irq+0x2c/0x3c)
	[56274.302952] [<c0074f44>] (generic_handle_irq+0x2c/0x3c) from
	[<c000ef80>] (handle_IRQ+0x40/0x90)
	[56274.311706] [<c000ef80>] (handle_IRQ+0x40/0x90) from
	[<c000dc80>] (__irq_svc+0x40/0x70)
	[56274.319697] [<c000dc80>] (__irq_svc+0x40/0x70) from
	[<c038113c>] (_raw_spin_unlock_irqrestore+0x10/0x48)
	[56274.329158] [<c038113c>]
	(_raw_spin_unlock_irqrestore+0x10/0x48) from [<c0200034>]
	(tty_port_tty_get+0x58/0x90)
	[56274.339213] [<c0200034>] (tty_port_tty_get+0x58/0x90) from
	[<c0212008>] (sirfsoc_uart_pio_rx_chars+0x1c/0xc8)
	[56274.349097] [<c0212008>]
	(sirfsoc_uart_pio_rx_chars+0x1c/0xc8) from [<c0212ef8>]
	(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc)
	[56274.359853] [<c0212ef8>]
	(sirfsoc_rx_tmo_process_tl+0xe4/0x1fc) from [<c0027c04>]
	(tasklet_action+0x84/0x114)
	[56274.369739] [<c0027c04>] (tasklet_action+0x84/0x114) from
	[<c0027db4>] (__do_softirq+0x120/0x200)
	[56274.378585] [<c0027db4>] (__do_softirq+0x120/0x200) from
	[<c0027f44>] (do_softirq+0x54/0x5c)
	[56274.386998] [<c0027f44>] (do_softirq+0x54/0x5c) from
	[<c00281ec>] (irq_exit+0x9c/0xd0)
	[56274.394899] [<c00281ec>] (irq_exit+0x9c/0xd0) from
	[<c000ef84>] (handle_IRQ+0x44/0x90)
	[56274.402790] [<c000ef84>] (handle_IRQ+0x44/0x90) from
	[<c000dc80>] (__irq_svc+0x40/0x70)
	[56274.410774] [<c000dc80>] (__irq_svc+0x40/0x70) from
	[<c0288af4>] (cpuidle_enter_state+0x50/0xe0)
	[56274.419532] [<c0288af4>] (cpuidle_enter_state+0x50/0xe0) from
	[<c0288c34>] (cpuidle_idle_call+0xb0/0x148)
	[56274.429080] [<c0288c34>] (cpuidle_idle_call+0xb0/0x148) from
	[<c000f3ac>] (arch_cpu_idle+0x8/0x38)
	[56274.438016] [<c000f3ac>] (arch_cpu_idle+0x8/0x38) from
	[<c0059344>] (cpu_startup_entry+0xfc/0x140)
	[56274.446956] [<c0059344>] (cpu_startup_entry+0xfc/0x140) from
	[<c04a3a54>] (start_kernel+0x2d8/0x2e4)
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All SiRFSoC UART registers are in 32-bits. If we use writeb for
TXFIFO, actually all of 32-bits are still written, for TXTIFO,
only low 8-bits are valid, so in prima2&atlas6, this causes no
problem.
But in the new atlas7, using writeb to write UART registers will
cause an imprecise data abort as HW does check the "wrong" writeb.
So move to writel and this also makes the code consistent with
sirfsoc_uart_pio_tx_chars() in which we use writel.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Two new drivers have been added since 3.14, the MEN 16z135 uart, and
the ARM semihosting console. Both are missing an explicit 'select
SERIAL_CORE', which can leads build errors when no other driver
selects the core, as found during ARM randconfig testing.
In case of the ARM semihosting console, we also have to select
SERIAL_CORE_CONSOLE.

This adds the missing 'select' statements.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes the warnings:

   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_rx':
>> drivers/tty/serial/sc16is7xx.c:548:1: warning: 'sc16is7xx_handle_rx' uses dynamic stack allocation [enabled by default]
   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_handle_tx':
>> drivers/tty/serial/sc16is7xx.c:589:1: warning: 'sc16is7xx_handle_tx' uses dynamic stack allocation [enabled by default]
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/sc16is7xx.c:1060:12: warning: 'sc16is7xx_probe' defined but not used [-Wunused-function]
 static int sc16is7xx_probe(struct device *dev,
            ^
drivers/tty/serial/sc16is7xx.c:1176:12: warning: 'sc16is7xx_remove' defined but not used [-Wunused-function]
 static int sc16is7xx_remove(struct device *dev)
            ^
drivers/tty/serial/sc16is7xx.c:1215:29: warning: 'regcfg' defined but not used [-Wunused-variable]
 static struct regmap_config regcfg = {
                             ^

Fixed these warnings by removing the `#ifdef CONFIG_REGMAP_I2C' around their
calls as this driver selects REGMAP_I2C in Kconfig. This part of driver just
didn't compile at all when REGMAP_I2C configured as module (CONFIG_REGMAP_I2C
is not defined, just CONFIG_REGMAP_I2C_MODULE).
Signed-off-by: NJan Moskyto Matejka <mq@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On initialization failure, an error message is already printed with
level KERN_ERR, no need to print another one with level KERN_INFO.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pch_uart driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 9aac5887 (tty/serial: add generic serial earlycon) moved
console option parsing from 8250_early.c and converted to kstrto*
functions from simple_strtoul along the way. However, kstrto* functions
are not equivalent in that they do not allow non-convertible characters
at the end such as "115200n8". Fix this by changing back to
simple_strtoul and ignore what checkpatch.pl says.
Reported-by: NYinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit d2fd6810 (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:

arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c

Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: NYinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix by including linux/uaccess.h:

   drivers/tty/serial/sc16is7xx.c: In function 'sc16is7xx_ioctl':
>> drivers/tty/serial/sc16is7xx.c:861:3: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
>> drivers/tty/serial/sc16is7xx.c:867:3: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A number of older CMOTech modems are based on Qualcomm
chips.  The blacklisted interfaces are QMI/wwan.
Reported-by: NLars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan

Cc: <stable@vger.kernel.org>
Reported-by: NJulio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The SC16IS7xx is a slave I2C-bus/SPI interface to a single-channel
high performance UART. The SC16IS7xx's internal register set is
backward-compatible with the widely used and widely popular 16C450.

The SC16IS7xx also provides additional advanced features such as
auto hardware and software flow control, automatic RS-485 support, and
software reset.
Signed-off-by: NJon Ringle <jringle@gridpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.

Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: NLudovic Drolez <ldrolez@debian.org>
Tested-by: NLudovic Drolez <ldrolez@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this
warning:
drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined
but not used [-Wunused-function]

Instead of creating nested #ifdefs, this patch fixes it by defining the
xHCI PCI stubs as inline.

This warning has been in since 3.2 kernel and was
caused by commit 421aa841
"usb/xhci: hide MSI code behind PCI bars", but wasn't noticed
until 3.13 when a configuration with these options was tried
Signed-off-by: NDavid Cohen <david.a.cohen@linux.intel.com>
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After suspend another Renesas PCI-X USB 3.0 card doesn't work.
[root@fedora-20 ~]# lspci -vmnnd 1912:
Device:	03:00.0
Class:	USB controller [0c03]
Vendor:	Renesas Technology Corp. [1912]
Device:	uPD720202 USB 3.0 Host Controller [0015]
SVendor:	Renesas Technology Corp. [1912]
SDevice:	uPD720202 USB 3.0 Host Controller [0015]
Rev:	02
ProgIf:	30

This patch should be applied to stable kernel 3.14 that contain
the commit 1aa9578c
"xhci: Fix resume issues on Renesas chips in Samsung laptops"
Reported-and-tested-by: NAnatoly Kharchenko <rfr-bugs@yandex.ru>
Reference: http://redmine.russianfedora.pro/issues/1315Signed-off-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com>
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The same issue like with Panther Point chipsets. If the USB ports are
switched to xHCI on shutdown, the xHCI host will send a spurious interrupt,
which will wake the system. Some BIOS have work around for this, but not all.
One example is Compulab's mini-desktop, the Intense-PC2.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.

This patch should be backported to stable kernels as old as 3.12,
that contain the commit 638298dc
"xhci: Fix spurious wakeups after S5 on Haswell"
Signed-off-by: NDenis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have observed a rare cycle state desync bug after Set TR Dequeue
Pointer commands on Intel LynxPoint xHCs (resulting in an endpoint that
doesn't fetch new TRBs and thus an unresponsive USB device). It always
triggers when a previous Set TR Dequeue Pointer command has set the
pointer to the final Link TRB of a segment, and then another URB gets
enqueued and cancelled again before it can be completed. Further
investigation showed that the xHC had returned the Link TRB in the TRB
Pointer field of the Transfer Event (CC == Stopped -- Length Invalid),
but when xhci_find_new_dequeue_state() later accesses the Endpoint
Context's TR Dequeue Pointer field it is set to the first TRB of the
next segment.

The driver expects those two values to be the same in this situation,
and uses the cycle state of the latter together with the address of the
former. This should be fine according to the XHCI specification, since
the endpoint ring should be stopped when returning the Transfer Event
and thus should not advance over the Link TRB before it gets restarted.
However, real-world XHCI implementations apparently don't really care
that much about these details, so the driver should follow a more
defensive approach to try to work around HC spec violations.

This patch removes the stopped_trb variable that had been used to store
the TRB Pointer from the last Transfer Event of a stopped TRB. Instead,
xhci_find_new_dequeue_state() now relies only on the Endpoint Context,
requiring a small amount of additional processing to find the virtual
address corresponding to the TR Dequeue Pointer. Some other parts of the
function were slightly rearranged to better fit into this model.

This patch should be backported to kernels as old as 2.6.31 that contain
the commit ae636747 "USB: xhci: URB
cancellation support."
Signed-off-by: NJulius Werner <jwerner@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit fcbee4d4.

It wasn't quite ready to go in yet, sorry about that.

Cc: Simon Horman <horms@verge.net.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add earlycon support for the arm/arm64 semihosting debug serial
interface. This allows enabling a debug console when early_params are
processed. This is based on the arm64 earlyprintk smh support and is
intended to replace it.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>