Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 11 8月, 2021 1 次提交
  3. 05 8月, 2021 3 次提交
  5. 31 7月, 2021 1 次提交
  7. 28 7月, 2021 1 次提交
  9. 24 7月, 2021 2 次提交
  11. 22 7月, 2021 4 次提交
    • M
      drm/i915: Make GT workaround upper bounds exclusive · 6b73a7f3
      由 Matt Roper 提交于 
      Workarounds are documented in the bspec with an exclusive upper bound
(i.e., a "fixed" stepping that no longer needs the workaround).  This
makes our driver's use of an inclusive upper bound for stepping ranges
confusing; the differing notation between code and bspec makes it very
easy for mistakes to creep in.

Let's switch the upper bound of our IS_{GT,DISP}_STEP macros over to use
an exclusive upper bound like the bspec does.  This also has the benefit
of helping make sure workarounds are properly handled for new minor
steppings that show up (e.g., an A1 between the A0 and B0 we already
knew about) --- if the new intermediate stepping pulls in hardware fixes
early, there will be an update to the workaround definition which lets
us know we need to change our code.  If the new stepping does not pull a
hardware fix earlier, then the new stepping will already be captured
properly by the "[begin, fix)" range in the code.

We'll probably need to be extra vigilant in code review of new
workarounds for the near future to make sure developers notice the new
semantics of workaround bounds.  But we just migrated a bunch of our
platforms from the IS_REVID bounds over to IS_{GT,DISP}_STEP, so people
are already adjusting to the new macros and now is a good time to make
this change too.

[mattrope: Split out GT changes to apply through gt-next tree]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-8-matthew.d.roper@intel.com
      6b73a7f3
    • M
      drm/i915: Program DFR enable/disable as a GT workaround · 1e1824de
      由 Matt Roper 提交于 
      DFR programming (which we enable as an optimization on gen11, but must
ensure is disabled on gen12) should be handled as a GT workaround rather
than clock gating initialization.  This will ensure that the programming
of these registers is verified with our typical workaround checks.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-4-matthew.d.roper@intel.com
      1e1824de
    • M
      drm/i915/icl: Drop a couple unnecessary workarounds · 131b1252
      由 Matt Roper 提交于 
      While doing a quick sanity check of the ICL workarounds in the driver I
noticed a few things that should be updated:

 * There's no mention in the bspec that WaPipelineFlushCoherentLines
   is needed on gen11 (both the current WA database and the old,
   deprecated page 20196 were checked); it appears this might have just
   been copied from the gen9 list?  Even if this were needed, it doesn't
   seem like this was the correct implementation anyway since the gen9
   workaround is supposed to be implemented in the indirect context bb
   (as we do in gen8_emit_flush_coherentl3_wa() on gen8/gen9).

 * WaForwardProgressSoftReset does not appear in the current workaround
   database.  The old deprecated workaround list has a note indicating
   the workaround was dropped in 2017, so we should be safe to drop it
   from the code too.

While we're at it, add the formal workaround ID number to
WaDisableBankHangMode (our hardware team made a transition from
text-based workaround names to ID numbers partway through the
development of ICL, which is why some workarounds only have names, some
only have numbers, and some have both).

Bspec: 33450
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-3-matthew.d.roper@intel.com
      131b1252
    • M
      drm/i915: Fix application of WaInPlaceDecompressionHang · f4fa096a
      由 Matt Roper 提交于 
      On SKL we've been applying this workaround on H0+ steppings, which is
actually backwards; H0 is supposed to be the first stepping where the
workaround is no longer needed.  Flip the bounds so that the workaround
applies to all steppings _before_ H0.

On BXT we've been applying this workaround to all steppings, but the
bspec tells us it's only needed until C0.  Pre-C0 GT steppings only
appeared in pre-production hardware, which we no longer support in the
driver, so we can drop the workaround completely for this platform.

On ICL we've been applying this workaround to all steppings, but there
doesn't seem to be any indication that this workaround was ever needed
for this platform (even now-deprecated page 20196 of the bspec doesn't
mention it).  We can go ahead and drop it.

I also don't see any mention of this workaround being needed for KBL,
although this may be an oversight since the workaround is needed for all
steppings of CFL.  I'll leave the workaround in place for KBL to be
safe.

Bspec: 14091, 33450
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-2-matthew.d.roper@intel.com
      f4fa096a
  13. 15 7月, 2021 6 次提交
  15. 14 7月, 2021 3 次提交
  17. 18 6月, 2021 2 次提交
    • M
      drm/i915: Add support for explicit L3BANK steering · 31939274
      由 Matt Roper 提交于 
      Because Render Power Gating restricts us to just a single subslice as a
valid steering target for reads of multicast registers in a SUBSLICE
range, the default steering we setup at init may not lead to a suitable
target for L3BANK multicast register.  In cases where it does not, use
explicit runtime steering whenever an L3BANK multicast register is read.

While we're at it, let's simplify the function a little bit and drop its
support for gen10/CNL since no such platforms ever materialized for real
use.  Multicast register steering is already an area that causes enough
confusion; no need to complicate it with what's effectively dead code.

v2:
 - Use gt->uncore instead of gt->i915->uncore.  (Tvrtko)
 - Use {} as table terminator.  (Rodrigo)

v3:
 - L3bank fuse register is a disable mask rather than an enable mask.
   We need to invert it before use.  (CI)

v4:
 - L3bank ID goes in the subslice field, not the slice field.  (CI)

Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210617211425.1943662-4-matthew.d.roper@intel.com
      31939274
    • M
      drm/i915: Add GT support for multiple types of multicast steering · 0957e931
      由 Matt Roper 提交于 
      Although most of our multicast registers are replicated per-subslice, we
also have a small number of multicast registers that are replicated
per-l3 bank instead.  For both types of multicast registers we need to
make sure we steer reads of these registers to a valid instance.
Ideally we'd like to find a specific instance ID that would steer reads
of either type of multicast register to a valid instance (i.e., not
fused off and not powered down), but sometimes the combination of
part-specific fusing and the additional restrictions imposed by Render
Power Gating make it impossible to find any overlap between the set of
valid subslices and valid l3 banks.  This problem will become even more
noticeable on our upcoming platforms since they will be adding
additional types of multicast registers with new types of replication
and rules for finding valid instances for reads.

To handle this we'll continue to pick a suitable subslice instance at
driver startup and program this as the default (sliceid,subsliceid)
setting in the steering control register (0xFDC).  In cases where we
need to read another type of multicast GT register, but the default
subslice steering would not correspond to a valid instance, we'll
explicitly re-steer the single read to a valid value, perform the read,
and then reset the steering to it's "subslice" default.

This patch adds the general functionality to prepare for this explicit
steering of other multicast register types.  We'll plug L3 bank steering
into this in the next patch, and then add additional types of multicast
registers when the support for our next upcoming platform arrives.

v2:
 - Use entry->end==0 as table terminator.  (Rodrigo)
 - Grab forcewake in wa_list_verify() now that we're using accessors
   that assume forcewake is already held.

v3:
 - Fix loop condition when iterating over steering range tables.
   (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210617211425.1943662-3-matthew.d.roper@intel.com
      0957e931
  19. 16 6月, 2021 1 次提交
  21. 06 6月, 2021 1 次提交
  23. 07 5月, 2021 1 次提交
  25. 09 4月, 2021 4 次提交
  27. 29 3月, 2021 3 次提交
  29. 25 3月, 2021 5 次提交
  31. 09 2月, 2021 1 次提交
  33. 01 2月, 2021 1 次提交