By tracking the current status of the backlight we can prevent recording
the value of the current backlight when we have disabled it. And so
prevent restoring it to 'off' after an unbalanced sequence of
intel_lvds_disable/enable.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=22672Tested-by: NAlex Riesen <raa.lkml@gmail.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Add an interrupt handler for switching graphics frequencies and handling
PM interrupts.  This should allow for increased performance when busy
and lower power consumption when idle.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

... otherwise the panel-fitter may be left enabled with random settings
and cause unintended filtering (i.e. blurring of native modes on external
panels).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31942Reported-and-tested-by: NBen Kohler <bkohler@gmail.com>
Tested-by: NCiprian Docan <docan@eden.rutgers.edu>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

A glorified s/obj_priv/obj/ with a net reduction of over a 100 lines and
many characters!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Fixes issue where i915_gfx_val was reporting values several
orders of magnitude higher than physically possible (without
leaving scorch marks on my thighs at least.)
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.

My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.

With this patch, my receiver has not lost sync yet (> 40 tries).

Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git

Two questions still remain:

I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?

Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Since we set the output type of PCH attached eDP panels to
INTEL_OUTPUT_eDP this function would never return true when it should.
It's been replaced by working functions.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The display code needs to distinguish between CPU and PCH attached eDP
panels, so add some helpers to handle that.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.

Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.

Based on an original patch by Jesse Barnes.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This ensures that we do wait upon the flushes to complete if necessary
and avoid the visual tears, whilst enabling pipelined page-flips.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

When separating out the prepare/commit into its own separate functions
we overlooked that the intel_crtc->dpms_mode was being used elsewhere to
check on the actual status of the pipe.

Track that bit of logic separately from the actual dpms mode, so there
is no confusion should we be able to handle multiple dpms modes, nor
any semantic conflict between prepare/commit and dpms.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

This closes a couple of corner cases where we introduced and forgot
about a couple of routines that need to be called when disabling the
crtc and then re-enabling it. The code needs to be moved again so that
the common bits are shared across generations.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Commit 77d07fd9 introduced a regression
where by not waiting for the panel to be turned off, left the panel and
PLL registers locked across the modeset. Thus the panel remaining blank.

As pointed out by Daniel Vetter, when testing LVDS it helps to open the
laptop and look at the actual panel you are purporting to test.

A second issue with the patch was that in order to modify the panel
fitter before gen5, the pipe and the panel must have be completely
powered down. So we wait.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Avoid a potentially long busy-wait if we not in the process of
atomically switching to the kdb console.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Currently we have a exact mapping of a connector onto an encoder for its
whole lifetime. Make this an explicit property of the structure and so
simplify the code.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Why iterate all the crtcs to find the pipe, when we already know which
crtc is attached to which pipe?
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.

Fixes:

  Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
  https://bugs.freedesktop.org/show_bug.cgi?id=29716

And a bug on one of my PineView boxes which overflowed the backlight
value.

Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During DPMS we currently do not want the overlay code to be
interruptible, so pass that information down and only take the
uninterrruptible paths.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can program the h/w to first wait on the flip and then switch off
without relying on s/w intervention. This removes the need for a double
step switch off, bringing much rejoicing.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The scoping of the validity of the mapping is thus clarified.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Store the pixel-multiplier on the adjusted mode and avoid modifying the
requested mode.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

wait_for() uses msleep() to yield the cpu whilst spinning waiting for a
register to change. kdb asserts that mode changes are atomic and so
prohibits msleep. The alternative would be to use mdelay or to simply
probe the register more often instead of busy waiting.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Jesse's feedback from using the wait_for() macro was that the msleep
argument was that it was superfluous and made the macro more difficult
to use and to read. As the actually amount of time to sleep is not
critical, the crucial part is to sleep and let the processor schedule
something else whilst we wait for the event, replace the argument with a
hardcoded value.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>

When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).

Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.

Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).

This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead.  Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

The i845 and i865 have a peculiarlity in that CURBASE is not the trigger
for the vsync update of the cursor registers but instead the
modification of that register is prohibited whilst the cursor is
enabled. Reorder the write sequence for CURPOS, CURCNTR and CURBASE on
i845 to i865 to match.

v2: Remove the checks for i845/i865 from within i9xx_cursor_update()
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

Add a new macro, wait_for, to simplify the act of waiting on a register
to change state. wait_for() takes three arguments, the condition to
inspect on every loop, the maximum amount of time to wait and whether to
yield the cpu for a length of time after each check.

v2: Upgrade failure messages to DRM_ERROR on the suggestion of
Eric Anholt. We do not expect to hit these conditions as they reflect
programming errors, so if we do we want to be notified.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

v2: Hook in DP paths to keep FULLSCREEN panel fitting on eDP.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The comments have long desired that we should switch off the cursor
along with the display plane, make it so.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

Make the code that tiny bit clearer by reducing the pointer dance.

2 files changed, 130 insertions(+), 147 deletions(-)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>

Subclass intel_encoder to reduce the pointer dance through
intel_encoder->dev_priv.

10 files changed, 896 insertions(+), 997 deletions(-)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NEric Anholt <eric@anholt.net>