If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.

Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Mostly cleanup.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Commit 51f65ebc ("IB/ipath - program intconfig register using new HT
irq hook"), which fixed interrupts for HyperTransport HCAs, broke PCI
Express HCAs, because for those HCAs, the driver uses the value of
pdev->irq before pci_enable_msi() and ends up getting a totally bogus
IRQ number.  Fix this by using the value of pdev->irq after
pci_enable_msi().
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove variables that are set but then never looked at in the ipath
driver.  These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We can sometimes trigger parity errors due to processor speculative
reads to our write-combined memory (mostly seen on Woodcrest).   Add a
stats counter for these.

Factored out the sendbuffererror buffer cancellation code so it can be
used in the new handling; suppress likely subsequent error messages if
within two jiffies of the cancellation.

Also restore 2 dropped TXE lines on hwe_bitsextant noticed while
debugging.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This also entailed a little GPIO-interrupt general cleanup.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Also added the word "Hardware" after "Fatal" to make it more obvious
that it's hardware, not software.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch only renames files, fixes product names, and updates
comments.
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We do a few more explicit checks for specific models, and now also support the
old PathScale serial number style, or new QLogic style.

This is backwards compatible with previous versions of software and hardware.
That is, older software will see a plausible serial number and correct GUID
when used with a new board, while newer software will correctly handle an
older board.
Signed-off-by: NMike Albaugh <mike.albaugh@qlogic.com>
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: "Michael S. Tsirkin" <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is required for even semi-decent performance on OpenIB.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The reset code now turns off the PRESENT flag during a reset, so that
other code won't attempt to access a device that's in mid-reset.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Make symbols that are only used in a single source file static.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This file contains routines and definitions specific to InfiniPath
devices that have PCI Express interfaces.
Signed-off-by: NBryan O'Sullivan <bos@pathscale.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>