According to hardware's description, after the reset occurs, the driver
needs to re-initialize the command queue before sending and receiving
any commands. Therefore, the VF's driver needs to identify the command
queue needs to re-initialize with HCLGEVF_STATE_CMD_DISABLE, and does
not allow sending or receiving commands before the re-initialization.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a Core/Global/IMP reset occurs, the hardware sets the reset status
register of all PF/VF and reports a reset interrupt to all PF/VF and
firmware.

When receiving the reset interrupt:
1. The firmware will wait for 100 ms before resetting the hardware and
   clear the reset status register of all PF when hardware reset is done.
2. The PF/VF driver needs to down the netdev within 100 ms and then wait
   for hardware reset to finish.
3. After firmware clearing the reset status register of all PF, the PF
   driver reinitializes the hardware and clear the reset status register
   of it's VF.
4. After PF driver clearing the reset status register of VF, the VF driver
   reinitializes the hardware.

This patch mainly add handling for the step 4.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF performs a function reset, the hardware will reset both PF
and all the VF belong to this PF. Hence, both PF's driver and VF's
driver need to perform corresponding reset operations.

Before PF driver asserting function reset to hardware, it firstly
set up VF's hardware reset status, and inform the VF driver with
HNAE3_VF_PF_FUNC_RESET, then VF driver sets this reset type to
reset_pending and shechule reset task to stop IO and waits for the
hardware reset status to clear. When PF driver has reinitialized the
hardware and is ready to process mailbox from VF, PF driver clears
VF's hardware reset status for VF to continue its reset process.

Also, this patch uses readl_poll_timeout to simplify the hardware reset
status waitting.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when VF need to reset itself, it will send a cmd to PF,
after receiving the VF reset requset, PF sends a cmd to inform
VF to enter the reset process and send a cmd to firmware to do the
actual reset for the VF, it is possible that firmware has resetted
the VF, but VF has not entered the reset process, which may cause
IO not stopped problem when firmware is resetting VF.

This patch fixes it by adjusting the VF reset process, when VF
need to reset itself, it will enter the reset process first, and
it will tell the PF to send cmd to firmware to reset itself.

Add member reset_pending to struct hclgevf_dev, which indicates that
there is reset event need to be processed by the VF's reset task, and
the VF's reset task chooses the highest-level one and clears other
low-level one when it processes reset_pending.

hclge_inform_reset_assert_to_vf function is unused now, but it will
be used to support the PF reset with VF working, so declare it in
the header file.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing reset, the reset handling function only need to
reinitialize hardware, it makes sense to add a function to
do that job. Also the error handling of hclgevf_init_hdev is
different when it is used in reset process.

This patch adds reset_hdev to reinitialize hardware when resetting.
Also, this patch removes the hclgevf_dev_ongoing_full_reset because
it is unused now.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac_hlist was initialized during adapter_up, which will be called
every time a vf device is first brought up, or every time when device
is brought up again after bringing all devices down. This means our
state of previous list is lost, causing a memleak if entries are
present in the list. To fix that, move list init to the condition
that performs initial one time adapter setup.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The locally maintained list for tracking hash mac table was
not freed during driver remove.
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RING_PUSH_REQUESTS_AND_CHECK_NOTIFY is already able to make sure backend sees
requests before req_prod is updated.
Signed-off-by: NJacob Wen <jian.w.wen@oracle.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RED Qdisc will now inform the drivers about the state of the harddrop
flag.  Refuse to offload in case harddrop is set.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turns out the threshold value is used in signed compares in the FW,
so we should avoid setting the top bit.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve log messages printed when RED can't be offloaded because
of Qdisc parameters.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain cases initialization logic which follows allocation of
the vNIC structure may want to validate the capabilities of that vNIC.
This is easy before vNIC is initialized for normal capabilities which
are at fixed offsets in control memory, easy to locate and read, but
poses a challenge if the capabilities are in form of TLVs.  Parse
the TLVs early on so other code can just access parsed info, instead
of having to do the parsing by itself.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move setting ctrl_bar pointer to the nfp_net_alloc function,
to make sure we can parse capabilities early in the following
patch.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Qdisc offload code is logically separate, and we will soon
do significant surgery on it to support more Qdiscs, so move
it to a separate file.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan configuration is not restored after interface donw/up sequence
(if dual-emac - both interfaces). Tested on am572x EVM.

Steps to check:
~# ip link add link eth1 name eth1.100 type vlan id 100
~# ifconfig eth0 down
~# ifconfig eth1 down

Try to remove vid and observe warning:
~# ip link del eth1.100
[  739.526757] net eth1: removing vlanid 100 from vlan filter
[  739.533322] failed to kill vid 0081/100 for device eth1

This patch fixes it, restoring only vlan ALE entries and all other
unicast/multicast entries are restored by system calling rx_mode ndo.
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this moment, mcast addresses are added for real device only
(reserved vlans for dual-emac mode), even if a mcast address was added
for some vlan only, thus ALE doesn't have corresponding vlan mcast
entries after vlan socket joined multicast group. So ALE drops vlan
frames with mcast addresses intended for vlans and potentially can
receive mcast frames for base ndev. That's not correct. So, fix it by
creating only vlan/mcast entries as requested. Patch doesn't use any
additional lists and is based on device mc address list and cpsw ALE
table entries.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As added in 3e59020a ("net: bql: add __netdev_tx_sent_queue()"), which
 see for performance rationale.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reviewed-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This just removes VLAN_TAG_PRESENT use.  VLAN TCI=0 special meaning is
deeply embedded in the driver code and so is left as is.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

return -ENOMEM directly instead of assigning it in a variable
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current driver dynamically allocates an skb and maps it as DMA Rx
buffer. In order to prepare for upcoming XDP changes, let's introduce a
different allocation scheme.
Buffers are allocated dynamically and mapped into hardware.
During the Rx operation the driver uses build_skb() to produce the
necessary buffers for the network stack.
This change increases performance ~15% on 64b packets with smmu disabled
and ~5% with smmu enabled
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Interferences on the SPI line could distort the response of
available buffer space. So at least we should check that the
response doesn't exceed the maximum available buffer space.
In error case increase a new error counter and retry it later.
This behavior avoids buffer errors in the QCA7000, which
results in an unnecessary chip reset including packet loss.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

draft-ietf-nvo3-geneve-08 says:

   It is strongly RECOMMENDED that Path MTU Discovery ([RFC1191],
   [RFC1981]) be used by setting the DF bit in the IP header when Geneve
   packets are transmitted over IPv4 (this is the default with IPv6).

Now that ICMP error handling is working for GENEVE, we can comply with
this recommendation.

Make this configurable, though, to avoid breaking existing setups. By
default, DF won't be set. It can be set or inherited from inner IPv4
packets. If it's configured to be inherited and we are encapsulating IPv6,
it will be set.

This only applies to non-lwt tunnels: if an external control plane is
used, tunnel key will still control the DF flag.

v2:
- DF behaviour configuration only applies for non-lwt tunnels, apply DF
  setting only if (!geneve->collect_md) in geneve_xmit_skb()
  (Stephen Hemminger)
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export an encap_err_lookup() operation to match an ICMP error against a
valid VNI.
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow users to set the IPv4 DF bit in outgoing packets, or to inherit its
value from the IPv4 inner header. If the encapsulated protocol is IPv6 and
DF is configured to be inherited, always set it.

For IPv4, inheriting DF from the inner header was probably intended from
the very beginning judging by the comment to vxlan_xmit(), but it wasn't
actually implemented -- also because it would have done more harm than
good, without handling for ICMP Fragmentation Needed messages.

According to RFC 7348, "Path MTU discovery MAY be used". An expired RFC
draft, draft-saum-nvo3-pmtud-over-vxlan-05, whose purpose was to describe
PMTUD implementation, says that "is a MUST that Vxlan gateways [...]
SHOULD set the DF-bit [...]", whatever that means.

Given this background, the only sane option is probably to let the user
decide, and keep the current behaviour as default.

This only applies to non-lwt tunnels: if an external control plane is
used, tunnel key will still control the DF flag.

v2:
- DF behaviour configuration only applies for non-lwt tunnels, move DF
  setting to if (!info) block in vxlan_xmit_one() (Stephen Hemminger)
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export an encap_err_lookup() operation to match an ICMP error against a
valid VNI.
Signed-off-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NSabrina Dubroca <sd@queasysnail.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in dev_err error message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/broadcom/genet/bcmgenet.c: In function 'bcmgenet_power_down':
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1136:6: warning:
 variable 'ret' set but not used [-Wunused-but-set-variable]

bcmgenet_power_down should return 'ret' instead of 0.

Fixes: ca8cf341 ("net: bcmgenet: propagate errors from bcmgenet_power_down")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use phy_check_link_status in more places in the state machine.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the recent changes in the state machine state PHY_AN isn't used
any longer and can be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In few places in the state machine the state is set to PHY_RUNNING or
PHY_NOLINK after doing a phy_read_status(). So factor this out to
phy_check_link_status().

First use it in phy_start_aneg(): By setting the state to PHY_RUNNING
or PHY_NOLINK directly we can remove the code to handle the case that
we're using interrupts and aneg was finished already.

Definition of phy_link_up and phy_link_down needs to be moved because
they are called in the new function.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If aneg isn't finished yet then the PHY reports the link as down.
There's no benefit in setting the state to PHY_AN because the next
state machine run would set the status to PHY_NOLINK anyway (except
in the meantime aneg has been finished and link is up). Therefore
we can set the state to PHY_RUNNING or PHY_NOLINK directly.

In addition change the do_carrier parameter in phy_link_down() to true.
If carrier was marked as up before (what should never be the case because
PHY was in state PHY_HALTED before) then we should mark it as down now.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If aneg is enabled and the PHY reports the link as up then definitely
aneg finished successfully. Therefore this check is useless and
can be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload of geneve decap rules is supported in NFP. Include geneve in the
check for supported types.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the recently added VXLAN and geneve helper functions to
determine the type of the netdev from its rtnl_link_ops.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>