On SPARC, writel() should not be used to write directly to memory
address but only to memory mapped I/O address otherwise it causes
data access exception.

Commit 147e81ec ("i40e: Test memory before ethtool alloc
succeeds") introduced a code that uses memory address to fake the HW
tail address and attempt to write to that address using writel()
causes kernel panic on SPARC. The issue is reproduced while changing
number of descriptors using ethtool.

This change resolves the panic by using HW read-only memory mapped
I/O register to fake HW tail address instead memory address.

e.g.
> ethtool -G eth2 tx 2048 rx 2048
i40e 0000:03:00.2 eth2: Changing Tx descriptor count from 512 to 2048.
i40e 0000:03:00.2 eth2: Changing Rx descriptor count from 512 to 2048
sun4v_data_access_exception: ADDR[fff8001f9734a000] CTX[0000]
TYPE[0004], going.
              \|/ ____ \|/
              "@'/ .. \`@"
              /_| \__/ |_\
                 \__U_/
ethtool(3273): Dax [#1]
CPU: 9 PID: 3273 Comm: ethtool Tainted: G            E
4.8.0-linux-net_temp+ #7
task: fff8001f96d7a660 task.stack: fff8001f97348000
TSTATE: 0000009911001601 TPC: 00000000103189e4 TNPC: 00000000103189e8 Y:
00000000    Tainted: G            E
TPC: <i40e_alloc_rx_buffers+0x124/0x260 [i40e]>
g0: fff8001f4eb64000 g1: 00000000000007ff g2: fff8001f9734b92c g3:
00203e0000000000
g4: fff8001f96d7a660 g5: fff8001fa6704000 g6: fff8001f97348000 g7:
0000000000000001
o0: 0006000046706928 o1: 00000000db3e2000 o2: fff8001f00000000 o3:
0000000000002000
o4: 0000000000002000 o5: 0000000000000001 sp: fff8001f9734afc1 ret_pc:
0000000010318a64
RPC: <i40e_alloc_rx_buffers+0x1a4/0x260 [i40e]>
l0: fff8001f4e8bffe0 l1: fff8001f4e8cffe0 l2: 00000000000007ff l3:
00000000ff000000
l4: 0000000000ff0000 l5: 000000000000ff00 l6: 0000000000cda6a8 l7:
0000000000e822f0
i0: fff8001f96380000 i1: 0000000000000000 i2: 00203edb00000000 i3:
0006000046706928
i4: 0000000002086320 i5: 0000000000e82370 i6: fff8001f9734b071 i7:
00000000103062d4
I7: <i40e_set_ringparam+0x3b4/0x540 [i40e]>
Call Trace:
 [00000000103062d4] i40e_set_ringparam+0x3b4/0x540 [i40e]
 [000000000094e2f8] dev_ethtool+0x898/0xbe0
 [0000000000965570] dev_ioctl+0x250/0x300
 [0000000000923800] sock_do_ioctl+0x40/0x60
 [000000000092427c] sock_ioctl+0x7c/0x280
 [00000000005ef040] vfs_ioctl+0x20/0x60
 [00000000005ef5d4] do_vfs_ioctl+0x194/0x4c0
 [00000000005ef974] SyS_ioctl+0x74/0xa0
 [0000000000406214] linux_sparc_syscall+0x34/0x44
Disabling lock debugging due to kernel taint
Caller[00000000103062d4]: i40e_set_ringparam+0x3b4/0x540 [i40e]
Caller[000000000094e2f8]: dev_ethtool+0x898/0xbe0
Caller[0000000000965570]: dev_ioctl+0x250/0x300
Caller[0000000000923800]: sock_do_ioctl+0x40/0x60
Caller[000000000092427c]: sock_ioctl+0x7c/0x280
Caller[00000000005ef040]: vfs_ioctl+0x20/0x60
Caller[00000000005ef5d4]: do_vfs_ioctl+0x194/0x4c0
Caller[00000000005ef974]: SyS_ioctl+0x74/0xa0
Caller[0000000000406214]: linux_sparc_syscall+0x34/0x44
Caller[0000000000107154]: 0x107154
Instruction DUMP: e43620c8
 e436204a  c45e2038
<c2a083a0> 82102000
 81cfe008  90086001
 82102000  81cfe008

Kernel panic - not syncing: Fatal exception
Signed-off-by: NTushar Dave <tushar.n.dave@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Separate the global private flags and the regular private flags per
interface into two arrays. Future additions of private flags will not
need to be duplicated which may lead to buggy code. Also rename
"i40e_priv_flags_strings_gl" to "i40e_gl_priv_flags_strings" for
clarity, as it reads more naturally.

Change-ID: I68caef3c9954eb7da342d7f9d20f2873186f2758
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed some of unnecessary if statements and unreachable code found by
static code analysis tool.
The return value of i40e_vsi_control_rings(..., false) is always 0. So,
test for non-zero will never be true. The function has been split into
"int i40e_vsi_start_rings()" and "void i40e_vsi_stop_rings()" for better
understanding.
Similarly, the function i40e_vsi_kill_vlan() never fails. So, checking
for return value is also unnecessary. Function definition changed to void.
The i40e_loopback_test() function is not implemented. The function and
all references to loopback testing were removed.

Change-ID: Id45cf66f6689ce2bc4e887de13f073e30e8431bd
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a common method for finding a VSI by type.  The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not.  This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.

Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

So the i40e driver had a really convoluted configuration for how to handle
the debug flags contained in msg_level.  Part of the issue is that the
driver has its own 32 bit mask that it was using to track a separate set of
debug features.  From what I can tell it was trying to use the upper 4 bits
to determine if the value was meant to represent a bit-mask or the numeric
value provided by debug level.

What this patch does is clean this up by compressing those 4 bits into bit
31, as a result we just have to perform a check against the value being
negative to determine if we are looking at a debug level (positive), or a
debug mask (negative).  The debug level will populate the msg_level, and
the debug mask will populate the debug_mask in the hardware struct.

I added similar logic for ethtool.  If the value being provided has bit 31
set we assume the value being provided is a debug mask, otherwise we assume
it is a msg_enable mask.  For displaying we only provide the msg_enable,
and if debug_mask is in use we will print it to the dmesg log.

Lastly I removed the debugfs interface.  It is redundant with what we
already have in ethtool and really doesn't belong anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move some data to text

$ size drivers/net/ethernet/intel/i40e/i40e_ethtool.o*
   text	   data	    bss	    dec	    hex	filename
  25012	      0	     32	  25044	   61d4	drivers/net/ethernet/intel/i40e/i40e_ethtool.o.new
  22868	   2120	     32	  25020	   61bc	drivers/net/ethernet/intel/i40e/i40e_ethtool.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit a75e8005 ("i40e: queue-specific settings for interrupt
moderation") the i40e driver gained support for setting interrupt
moderation values per queue. This patch adds support for this feature
to the i40evf driver as well. In addition, a few changes are made to
the i40e implementation to add function header documentation comments,
as well.

This behaves in a similar fashion to the implementation in i40e. Thus,
requesting the moderation value when no queue is provided will report
queue 0 value, while setting the value without a queue will set all
queues at once.

Change-ID: I1f310a57c8e6c84a8524c178d44d1b7a6d3a848e
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.

Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.

Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.

Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, when using ethtool to change the RSS hash key, ethtool would
report back saying the old key was still being used and no error was
reported.  It was unclear whether it was being reported incorrectly or
being set incorrectly.  Debugging revealed 'i40e_set_rxfh()' returned
zero immediately instead of setting the key because a user defined
indirection table is not supplied when changing the hash key.

This fix instead changes it such that if an indirection table is not
supplied, then a default one is created and the hash key is now
correctly set.

Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.

Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.

To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.

Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding the missing link advertise for some X710 NICs.
This can be observed by simply calling ethtool on the interface.
root@rhel7:~ # ethtool eth0
Settings for eth0:
        Supported ports: [ FIBRE ]
        Supported link modes:   10000baseT/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Advertised link modes:  Not reported
[...]
With fix applied.
root@rhel7:~ # ethtool eth0
Settings for eth0:
        Supported ports: [ FIBRE ]
        Supported link modes:   10000baseT/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Advertised link modes:  10000baseT/Full
[...]
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When link is down, Advertised Link Modes was wrongly displaying full
supported link modes instead of Advertised link mode. Added conditional
checks in order to make sure correct Advertised link modes are
displayed when the link is down.

Change-ID: I8a61413f9ee174149c7a33157b5f0b0a8da9842d
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Removing this code which wasn't allowing 100BaseT to show up in the supported
link modes for 10GBaseT PHYs.

Change-ID: Iada2eafa7ef6b4bac9a2a1380ff533ae5de51e1d
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a Direct Attach (DA) cable is used, if the i40e_set_settings
function is called it would return an error. Add the DA type so
the function won't fail.

Change-ID: I2b802f27a5d91cfefa72fd1f852acb4d74647a8e
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.

Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.

The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.

For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.

Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP                    : off
LinkPolling            : off
flow-director-atr      : on
veb-stats              : off
hw-atr-eviction        : off
vf-true-promisc-support: off

to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on

At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic

Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add flag to tell firmware to disable link on all ports.

This patch changes the bits set for telling firmware the PHY needs
to be modified by driver.  Without this patch, the setting will only
set that mode for the current port on the device.  Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.

Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When testing on systems with very limited amounts of RAM, a bug was
found where, while changing the number of descriptors using ethtool,
the driver didn't test the limits of system memory before permanently
assuming it would be able to get receive buffer memory.

Work around this issue by pre-allocation of the receive buffer
memory, in the "ghost" ring, which is then used during reinit
using the new ring length.

Change-Id: I92d7a5fb59a6c884b2efdd1ec652845f101c3359
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is part 1 of the Rx refactor series, just including
changes to i40e.

This refactor aligns the receive routine with the one in
ixgbe which was highly optimized.  This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.

In order to do this:
- consolidate the receive path into a single function that doesn't
  use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split

Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A little bit of code cleanup in prep for more cloud filter work.

Change-ID: I0dc33ce0d4c207944336a07437640fef920c100c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100baseT/Full is now listed and supported link mode for 10GBaseT PHY.
This is a fix to list all the supported link modes of 10GBaseT PHY.

Change-ID: If2be3212ef0fef85fd5d6e4550c7783de2f915e9
Signed-off-by: NAvinash Dayanand <avinash.dayanand@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: NStefan Assmann <sassmann@kpanic.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements set_per_queue_coalesce for i40e driver.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements get_per_queue_coalesce for i40e driver.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: NKan Liang <kan.liang@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new AdminQ functions for safely accessing the Rx control
registers that may be affected by heavy small packet traffic.

We can't use AdminQ calls in i40e_clear_hw() because the HW is being
initialized and the AdminQ is not alive.  We recently added an AQ
related replacement for reading PFLAN_QALLOC, and this patch puts
back the original register read.

Change-ID: Ib027168c954a5733299aa3a4ce5f8218c6bb5636
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where the ethtool identify adapter
functionality did not work for some copper PHY's.  Without this
patch, the blink led functionality fails on some parts.  This
patch adds PHY write code to blink led's on parts where this
functionality is contained in the PHY rather than the MAC.

Change-ID: Iee7b3453f61d5ffd0b3d03f720ee4f17f919fcc2
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.

Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.

Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.

Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The new parameters for add_veb allow us to enable and disable VEB stats,
so let's use them.

Update copyright year.

Change-ID: Ie6e68c68e2d1d459e42168eda661051b56bf0a65
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X722 can support automatic rule eviction for automatically added
flow director rules.  Feature is (should be) disabled by default.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver already counted allocation errors, so print
them as part of the ethtool -S output.  Useful for debugging
if your system is having trouble making memory available for
the driver.

Change-ID: I83839fa86e81e6d80f03b917c88dd3ef9a64dde0
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Sometimes, ARQ overflows are a big deal and tell us that the
firmware/hardware/driver/something is having problems. But normally
they're no big deal. To assist in assessing this, add a counter to
our Ethtool stats. A handful of ARQ overflows during VF init is no
problem. A large, ever-growing number indicates that Something Bad is
happening.

Change-ID: Ie5348bfbc8a54a890559cb00279c28d976a55096
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add some missing reporting/advertisement of 100Mb capability
for adapters that support it.

Change-ID: I8b8523fbdc99517bec29d90c71b3744db11542ac
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PCTYPES for the X710 and X722 families are different. This patch
makes adjustments for that.
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100M SGMII is only supported on X722.  Replace the mac check with
a feature flag check that is only set for the X722 device.

Change-ID: I53452d9af6af8cd9dca8500215fbc6ce93418f52
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the Hash PCTYPE enable for X722 since it supports
a broader selection of PCTYPES for TCP and UDP.

This patch also fixes a bug in XL710, X710, X722 support for RSS,
as of now we cannot reduce the (4)tuple for RSS for TCP/IPv4/IPV6 or
UDP/IPv4/IPv6 packets since this requires a product feature change
that comes in a later release.

A VF should never be allowed to change the tuples for RSS for any
PCTYPE since that's a global setting for the device in case of i40e
devices.

Change-ID: I0ee7203c9b24813260f58f3220798bc9d9ac4a12
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>