i40e: better error reporting for nvmupdate

Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.

Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ethernet/intel/i40e/i40e_ethtool.c

@@ -1005,16 +1005,19 @@ static int i40e_get_eeprom(struct net_device *netdev,
 	/* check for NVMUpdate access method */
 	magic = hw->vendor_id | (hw->device_id << 16);
 	if (eeprom->magic && eeprom->magic != magic) {
-		struct i40e_nvm_access *cmd;
-		int errno;
+		struct i40e_nvm_access *cmd = (struct i40e_nvm_access *)eeprom;
+		int errno = 0;
 
 		/* make sure it is the right magic for NVMUpdate */
 		if ((eeprom->magic >> 16) != hw->device_id)
-			return -EINVAL;
+			errno = -EINVAL;
+		else if (test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state) ||
+			 test_bit(__I40E_RESET_INTR_RECEIVED, &pf->state))
+			errno = -EBUSY;
+		else
+			ret_val = i40e_nvmupd_command(hw, cmd, bytes, &errno);
 
-		cmd = (struct i40e_nvm_access *)eeprom;
-		ret_val = i40e_nvmupd_command(hw, cmd, bytes, &errno);
-		if (ret_val && (hw->debug_mask & I40E_DEBUG_NVM))
+		if ((errno || ret_val) && (hw->debug_mask & I40E_DEBUG_NVM))
 			dev_info(&pf->pdev->dev,
 				 "NVMUpdate read failed err=%d status=0x%x errno=%d module=%d offset=0x%x size=%d\n",
 				 ret_val, hw->aq.asq_last_status, errno,
@@ -1098,27 +1101,25 @@ static int i40e_set_eeprom(struct net_device *netdev,
 	struct i40e_netdev_priv *np = netdev_priv(netdev);
 	struct i40e_hw *hw = &np->vsi->back->hw;
 	struct i40e_pf *pf = np->vsi->back;
-	struct i40e_nvm_access *cmd;
+	struct i40e_nvm_access *cmd = (struct i40e_nvm_access *)eeprom;
 	int ret_val = 0;
-	int errno;
+	int errno = 0;
 	u32 magic;
 
 	/* normal ethtool set_eeprom is not supported */
 	magic = hw->vendor_id | (hw->device_id << 16);
 	if (eeprom->magic == magic)
-		return -EOPNOTSUPP;
-
+		errno = -EOPNOTSUPP;
 	/* check for NVMUpdate access method */
-	if (!eeprom->magic || (eeprom->magic >> 16) != hw->device_id)
-		return -EINVAL;
-
-	if (test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state) ||
-	    test_bit(__I40E_RESET_INTR_RECEIVED, &pf->state))
-		return -EBUSY;
+	else if (!eeprom->magic || (eeprom->magic >> 16) != hw->device_id)
+		errno = -EINVAL;
+	else if (test_bit(__I40E_RESET_RECOVERY_PENDING, &pf->state) ||
+		 test_bit(__I40E_RESET_INTR_RECEIVED, &pf->state))
+		errno = -EBUSY;
+	else
+		ret_val = i40e_nvmupd_command(hw, cmd, bytes, &errno);
 
-	cmd = (struct i40e_nvm_access *)eeprom;
-	ret_val = i40e_nvmupd_command(hw, cmd, bytes, &errno);
-	if (ret_val && (hw->debug_mask & I40E_DEBUG_NVM))
+	if ((errno || ret_val) && (hw->debug_mask & I40E_DEBUG_NVM))
 		dev_info(&pf->pdev->dev,
 			 "NVMUpdate write failed err=%d status=0x%x errno=%d module=%d offset=0x%x size=%d\n",
 			 ret_val, hw->aq.asq_last_status, errno,

drivers/net/ethernet/intel/i40e/i40e_main.c

@@ -3475,6 +3475,7 @@ static irqreturn_t i40e_intr(int irq, void *data)
 	if (icr0 & I40E_PFINT_ICR0_ADMINQ_MASK) {
 		ena_mask &= ~I40E_PFINT_ICR0_ENA_ADMINQ_MASK;
 		set_bit(__I40E_ADMINQ_EVENT_PENDING, &pf->state);
+		i40e_debug(&pf->hw, I40E_DEBUG_NVM, "AdminQ event\n");
 	}
 
 	if (icr0 & I40E_PFINT_ICR0_MAL_DETECT_MASK) {
@@ -6332,7 +6333,9 @@ static void i40e_clean_adminq_subtask(struct i40e_pf *pf)
 		case i40e_aqc_opc_nvm_erase:
 		case i40e_aqc_opc_nvm_update:
 		case i40e_aqc_opc_oem_post_update:
-			i40e_debug(&pf->hw, I40E_DEBUG_NVM, "ARQ NVM operation completed\n");
+			i40e_debug(&pf->hw, I40E_DEBUG_NVM,
+				   "ARQ NVM operation 0x%04x completed\n",
+				   opcode);
 			break;
 		default:
 			dev_info(&pf->pdev->dev,