In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

	There's a bunch of failure exits in ffs_fs_mount() with
seriously broken recovery logics.  Most of that appears to stem
from misunderstanding of the ->kill_sb() semantics; unlike
->put_super() it is called for *all* superblocks of given type,
no matter how (in)complete the setup had been.  ->put_super()
is called only if ->s_root is not NULL; any failure prior to
setting ->s_root will have the call of ->put_super() skipped.
->kill_sb(), OTOH, awaits every superblock that has come from
sget().

Current behaviour of ffs_fs_mount():

We have struct ffs_sb_fill_data data on stack there.  We do
	ffs_dev = functionfs_acquire_dev_callback(dev_name);
and store that in data.private_data.  Then we call mount_nodev(),
passing it ffs_sb_fill() as a callback.  That will either fail
outright, or manage to call ffs_sb_fill().  There we allocate an
instance of struct ffs_data, slap the value of ffs_dev (picked
from data.private_data) into ffs->private_data and overwrite
data.private_data by storing ffs into an overlapping member
(data.ffs_data).  Then we store ffs into sb->s_fs_info and attempt
to set the rest of the things up (root inode, root dentry, then
create /ep0 there).  Any of those might fail.  Should that
happen, we get ffs_fs_kill_sb() called before mount_nodev()
returns.  If mount_nodev() fails for any reason whatsoever,
we proceed to
	functionfs_release_dev_callback(data.ffs_data);

That's broken in a lot of ways.  Suppose the thing has failed in
allocation of e.g. root inode or dentry.  We have
	functionfs_release_dev_callback(ffs);
	ffs_data_put(ffs);
done by ffs_fs_kill_sb() (ffs accessed via sb->s_fs_info), followed by
	functionfs_release_dev_callback(ffs);
from ffs_fs_mount() (via data.ffs_data).  Note that the second
functionfs_release_dev_callback() has every chance to be done to freed memory.

Suppose we fail *before* root inode allocation.  What happens then?
ffs_fs_kill_sb() doesn't do anything to ffs (it's either not called at all,
or it doesn't have a pointer to ffs stored in sb->s_fs_info).  And
	functionfs_release_dev_callback(data.ffs_data);
is called by ffs_fs_mount(), but here we are in nasal daemon country - we
are reading from a member of union we'd never stored into.  In practice,
we'll get what we used to store into the overlapping field, i.e. ffs_dev.
And then we get screwed, since we treat it (struct gfs_ffs_obj * in
disguise, returned by functionfs_acquire_dev_callback()) as struct
ffs_data *, pick what would've been ffs_data ->private_data from it
(*well* past the actual end of the struct gfs_ffs_obj - struct ffs_data
is much bigger) and poke in whatever it points to.

FWIW, there's a minor leak on top of all that in case if ffs_sb_fill()
fails on kstrdup() - ffs is obviously forgotten.

The thing is, there is no point in playing all those games with union.
Just allocate and initialize ffs_data *before* calling mount_nodev() and
pass a pointer to it via data.ffs_data.  And once it's stored in
sb->s_fs_info, clear data.ffs_data, so that ffs_fs_mount() knows that
it doesn't need to kill the sucker manually - from that point on
we'll have it done by ->kill_sb().
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@vger.kernel.org> # 3.3+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: NRamneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Trying to read data from the Pegasus Technologies NoteTaker (0e20:0101)
[1] with the Windows App (EasyNote) works natively but fails when
Windows is running under KVM (and the USB device handed to KVM).

The reason is a USB control message
 usb 4-2.2: control urb: bRequestType=22 bRequest=09 wValue=0200 wIndex=0001 wLength=0008
This goes to endpoint address 0x01 (wIndex); however, endpoint address
0x01 does not exist. There is an endpoint 0x81 though (same number,
but other direction); the app may have meant that endpoint instead.

The kernel thus rejects the IO and thus we see the failure.

Apparently, Linux is more strict here than Windows ... we can't change
the Win app easily, so that's a problem.

It seems that the Win app/driver is buggy here and the driver does not
behave fully according to the USB HID class spec that it claims to
belong to.  The device seems to happily deal with that though (and
seems to not really care about this value much).

So the question is whether the Linux kernel should filter here.
Rejecting has the risk that somewhat non-compliant userspace apps/
drivers (most likely in a virtual machine) are prevented from working.
Not rejecting has the risk of confusing an overly sensitive device with
such a transfer. Given the fact that Windows does not filter it makes
this risk rather small though.

The patch makes the kernel more tolerant: If the endpoint address in
wIndex does not exist, but an endpoint with toggled direction bit does,
it will let the transfer through. (It does NOT change the message.)

With attached patch, the app in Windows in KVM works.
 usb 4-2.2: check_ctrlrecip: process 13073 (qemu-kvm) requesting ep 01 but needs 81

I suspect this will mostly affect apps in virtual environments; as on
Linux the apps would have been adapted to the stricter handling of the
kernel. I have done that for mine[2].

[1] http://www.pegatech.com/
[2] https://sourceforge.net/projects/notetakerpen/Signed-off-by: NKurt Garloff <kurt@garloff.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If NO_DMA=y:

drivers/built-in.o: In function `dma_set_coherent_mask':
include/linux/dma-mapping.h:93: undefined reference to `dma_supported'
Reviewed-and-tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a pending TD which is not freed after request finishes,
we do this due to a controller bug. This TD needs to be freed when
the driver is removed. It prints below error message when unload
chipidea driver at current code:
"ci_hdrc ci_hdrc.0: dma_pool_destroy ci_hw_td, b0001000 busy"
It indicates the buffer at dma pool are still in use.

This commit will free the pending TD at driver's removal procedure,
it can fix the problem described above.
Acked-by: NMichael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If not, the PHY will be active even the controller is not in use.
We find this issue due to the PHY's clock refcount is not correct
due to -EPROBE_DEFER return after phy's init.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It needs to free ci->hw_bank.regmap explicitly since it is not managed
resource.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When we rmmod gadget, the ci->driver needs to be cleared.
Otherwise, when we plug in usb cable again, the driver will
consider gadget is there, and go to enumeration procedure,
but in fact, it was removed.

ci_hdrc ci_hdrc.0: Connected to host
Unable to handle kernel paging request at virtual address 7f02a42c
pgd = 80004000
[7f02a42c] *pgd=3f13d811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] SMP ARM
Modules linked in: usb_f_acm u_serial libcomposite configfs [last unloaded: g_serial]
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0+ #42
task: 807dba88 ti: 807d0000 task.ti: 807d0000
PC is at udc_irq+0x8fc/0xea4
LR is at l2x0_cache_sync+0x5c/0x6c
pc : [<803de7f4>]    lr : [<8001d0f0>]    psr: 20000193
sp : 807d1d98  ip : 807d1d80  fp : 807d1df4
r10: af809900  r9 : 808184d4  r8 : 00080001
r7 : 00082001  r6 : afb711f8  r5 : afb71010  r4 : ffffffea
r3 : 7f02a41c  r2 : afb71010  r1 : 807d1dc0  r0 : afb71068
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7d  Table: 3f01804a  DAC: 00000017
Process swapper/0 (pid: 0, stack limit = 0x807d0238)
Stack: (0x807d1d98 to 0x807d2000)
1d80:                                                       00000000 afb71014
1da0: 000040f6 00000000 00000001 00000000 00007530 00000000 afb71010 001dcd65
1dc0: 01000680 00400000 807d1e2c afb71010 0000004e 00000000 00000000 0000004b
1de0: 808184d4 af809900 807d1e0c 807d1df8 803dbc24 803ddf04 afba75c0 0000004e
1e00: 807d1e44 807d1e10 8007a19c 803dbb9c 8108e7e0 8108e7e0 9ceddce0 af809900
1e20: 0000004e 807d0000 0000004b 00000000 00000010 00000000 807d1e5c 807d1e48
1e40: 8007a334 8007a154 af809900 0000004e 807d1e74 807d1e60 8007d3b4 8007a2f0
1e60: 0000004b 807cce3c 807d1e8c 807d1e78 80079b08 8007d300 00000180 807d8ba0
1e80: 807d1eb4 807d1e90 8000eef4 80079aec 00000000 f400010c 807d8ce4 807d1ed8
1ea0: f4000100 96d5c75d 807d1ed4 807d1eb8 80008600 8000eeac 8042699c 60000013
1ec0: ffffffff 807d1f0c 807d1f54 807d1ed8 8000e180 800085dc 807d1f20 00000046
1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010
1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff
1f20: 9cedd275 00000010 00000005 8108f080 8108f080 00000001 807de248 8086bd00
1f40: 807d0000 00000001 807d1f7c 807d1f58 80426af0 80426950 807d0000 00000000
1f60: 808184c0 808184c0 807d8954 805b886c 807d1f8c 807d1f80 8000f294 80426a44
1f80: 807d1fac 807d1f90 8005f110 8000f288 807d1fac 807d8908 805b4748 807dc86c
1fa0: 807d1fbc 807d1fb0 805aa58c 8005f068 807d1ff4 807d1fc0 8077c860 805aa530
1fc0: ffffffff ffffffff 8077c330 00000000 00000000 807bef88 00000000 10c53c7d
1fe0: 807d88d0 807bef84 00000000 807d1ff8 10008074 8077c594 00000000 00000000
Backtrace:
[<803ddef8>] (udc_irq+0x0/0xea4) from [<803dbc24>] (ci_irq+0x94/0x14c)
[<803dbb90>] (ci_irq+0x0/0x14c) from [<8007a19c>] (handle_irq_event_percpu+0x54/0x19c)
 r5:0000004e r4:afba75c0
 [<8007a148>] (handle_irq_event_percpu+0x0/0x19c) from [<8007a334>] (handle_irq_event+0x50/0x70)
[<8007a2e4>] (handle_irq_event+0x0/0x70) from [<8007d3b4>] (handle_fasteoi_irq+0xc0/0x16c)
 r5:0000004e r4:af809900
 [<8007d2f4>] (handle_fasteoi_irq+0x0/0x16c) from [<80079b08>] (generic_handle_irq+0x28/0x38)
 r5:807cce3c r4:0000004b
 [<80079ae0>] (generic_handle_irq+0x0/0x38) from [<8000eef4>] (handle_IRQ+0x54/0xb4)
 r4:807d8ba0 r3:00000180
 [<8000eea0>] (handle_IRQ+0x0/0xb4) from [<80008600>] (gic_handle_irq+0x30/0x64)
 r8:96d5c75d r7:f4000100 r6:807d1ed8 r5:807d8ce4 r4:f400010c
 r3:00000000
 [<800085d0>] (gic_handle_irq+0x0/0x64) from [<8000e180>] (__irq_svc+0x40/0x54)
Exception stack(0x807d1ed8 to 0x807d1f20)
1ec0:                                                       807d1f20 00000046
1ee0: 9cedd275 00000010 8108f080 807de294 00000001 807de248 96d5c75d 00000010
1f00: 00000000 807d1f54 00000000 807d1f20 8005ff54 8042699c 60000013 ffffffff
 r7:807d1f0c r6:ffffffff r5:60000013 r4:8042699c
 [<80426944>] (cpuidle_enter_state+0x0/0xf4) from [<80426af0>] (cpuidle_idle_call+0xb8/0x174)
 r9:00000001 r8:807d0000 r7:8086bd00 r6:807de248 r5:00000001
 r4:8108f080
 [<80426a38>] (cpuidle_idle_call+0x0/0x174) from [<8000f294>] (arch_cpu_idle+0x18/0x5c)
[<8000f27c>] (arch_cpu_idle+0x0/0x5c) from [<8005f110>] (cpu_startup_entry+0xb4/0x148)
[<8005f05c>] (cpu_startup_entry+0x0/0x148) from [<805aa58c>] (rest_init+0x68/0x80)
 r7:807dc86c
 [<805aa524>] (rest_init+0x0/0x80) from [<8077c860>] (start_kernel+0x2d8/0x334)
[<8077c588>] (start_kernel+0x0/0x334) from [<10008074>] (0x10008074)
Code: e59031e0 e51b203c e24b1034 e2820058 (e5933010)
---[ end trace f874b2c5533c04bc ]---
Kernel panic - not syncing: Fatal exception in interrupt
Tested-by: NMarek Vasut <marex@denx.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP.  The corresponding change has already
been made for ohci-hcd.

Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 24f53137 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd.  URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright.  Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet.  This is what client drivers expect.

This patch implements the same policy in ohci-hcd.  The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does.  Rather, it
depends on the hardware adding completed TDs to a "done queue".  Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place.  As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.

To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired).  Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way.  If so, it gives back the next URB right away.

This should be applied to all kernels containing commit 815fa7b9
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 24f53137 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd.  URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright.  Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet.  This is what client drivers expect.

This patch implements the same policy in uhci-hcd.  It should be
applied to all kernels containing commit c44b2250 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 24f53137 (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd.  URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright.  Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet.  This is what client drivers expect.

The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it.  As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set.  I don't have any way to test this change,
unfortunately.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-usb-linus-2013-09-23' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus

Sarah writes:

xhci: Bug fixes for 3.12.

Hi Greg,

Here's five bug fixes for 3.12.

The first two bugs fix issues with the command cancellation handling,
which can lead to oopses or the xHCI driver attempting to handle
previously-completed transfers.  People have been running into oopses
and odd behavior with command cancellation for a couple kernel releases,
so they're marked for stable.

The third patch fixes an issue with USB remote wakeup under xHCI that
can only be reproduced under ChromeOS.  As discussed, this fix is not
urgent, and isn't marked for stable.

The fourth patch fixes a race condition between URB cancellation and
userspace clearing an endpoint stall.  The fifth patch removes some
annoying dmesg spam when a USB 3.0 device is disconnected, by avoiding
sending a Set SEL request.

Sarah Sharp

Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: NXenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: NMartin MOKREJS <mmokrejs@gmail.com>
Suggested-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699Signed-off-by: NFlorian Wolter <wolly84@web.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.

EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:

                        /* stop resume signaling */
                        temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
                        ehci_writel(ehci, temp, status_reg);
                        clear_bit(wIndex, &ehci->resuming_ports);
                        retval = ehci_handshake(ehci, status_reg,
                                        PORT_RESUME, 0, 2000 /* 2msec */);

Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core.  When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.

After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device.  The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7.  The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.

This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0.  ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.

I attempted to replicate this bug with Ubuntu 12.04, but could not.  I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with.  I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.

Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)

Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.

This should also solve some weird behavior happening in command cancellation cases.

This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
    http://marc.info/?l=linux-usb&m=136269803207465&w=2

This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c "xHCI: add aborting
command ring function"
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.

Don't handle command completion events on stopped cmd ring if ring is
empty.

This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c "xHCI: add aborting
command ring function"
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: NGiovanni <giovanni.nervi@yahoo.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Pull staging fixes from Greg KH:
 "Here are a number of small staging tree and iio driver fixes.  Nothing
  major, just lots of little things"

* tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
  iio:buffer_cb: Add missing iio_buffer_init()
  iio: Prevent race between IIO chardev opening and IIO device free
  iio: fix: Keep a reference to the IIO device for open file descriptors
  iio: Stop sampling when the device is removed
  iio: Fix crash when scan_bytes is computed with active_scan_mask == NULL
  iio: Fix mcp4725 dev-to-indio_dev conversion in suspend/resume
  iio: Fix bma180 dev-to-indio_dev conversion in suspend/resume
  iio: Fix tmp006 dev-to-indio_dev conversion in suspend/resume
  iio: iio_device_add_event_sysfs() bugfix
  staging: iio: ade7854-spi: Fix return value
  staging:iio:hmc5843: Fix measurement conversion
  iio: isl29018: Fix uninitialized value
  staging:iio:dummy fix kfifo_buf kconfig dependency issue if kfifo modular and buffer enabled for built in dummy driver.
  iio: at91: fix adc_clk overflow
  staging: line6: add bounds check in snd_toneport_source_put()
  Staging: comedi: Fix dependencies for drivers misclassified as PCI
  staging: r8188eu: Adjust RX gain
  staging: r8188eu: Fix smatch warning in core/rtw_ieee80211.
  staging: r8188eu: Fix smatch error in core/rtw_mlme_ext.c
  staging: r8188eu: Fix Smatch off-by-one warning in hal/rtl8188e_hal_init.c
  ...

Pull USB fixes from Greg KH:
 "Here are a number of small USB fixes for 3.12-rc2.

  One is a revert of a EHCI change that isn't quite ready for 3.12.
  Others are minor things, gadget fixes, Kconfig fixes, and some quirks
  and documentation updates.

  All have been in linux-next for a bit"

* tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: pl2303: distinguish between original and cloned HX chips
  USB: Faraday fotg210: fix email addresses
  USB: fix typo in usb serial simple driver Kconfig
  Revert "USB: EHCI: support running URB giveback in tasklet context"
  usb: s3c-hsotg: do not disconnect gadget when receiving ErlySusp intr
  usb: s3c-hsotg: fix unregistration function
  usb: gadget: f_mass_storage: reset endpoint driver data when disabled
  usb: host: fsl-mph-dr-of: Staticize local symbols
  usb: gadget: f_eem: Staticize eem_alloc
  usb: gadget: f_ecm: Staticize ecm_alloc
  usb: phy: omap-usb3: Fix return value
  usb: dwc3: gadget: avoid memory leak when failing to allocate all eps
  usb: dwc3: remove extcon dependency
  usb: gadget: add '__ref' for rndis_config_register() and cdc_config_register()
  usb: dwc3: pci: add support for BayTrail
  usb: gadget: cdc2: fix conversion to new interface of f_ecm
  usb: gadget: fix a bug and a WARN_ON in dummy-hcd
  usb: gadget: mv_u3d_core: fix violation of locking discipline in mv_u3d_ep_disable()

Pull drm fixes from Dave Airlie:
 - some small fixes for msm and exynos
 - a regression revert affecting nouveau users with old userspace
 - intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  Revert "drm: mark context support as a legacy subsystem"
  drm/i915: Don't enable the cursor on a disable pipe
  drm/i915: do not update cursor in crtc mode set
  drm/exynos: fix return value check in lowlevel_buffer_allocate()
  drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
  drm/exynos: Fix address space warning in exynos_drm_buf.c
  drm/exynos: Remove redundant OF dependency
  drm/msm: drop unnecessary set_need_resched()
  drm/i915: kill set_need_resched
  drm/msm: fix potential NULL pointer dereference
  drm/i915/dvo: set crtc timings again for panel fixed modes
  drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
  drm/msm: workaround for missing irq
  drm/msm: return -EBUSY if bo still active
  drm/msm: fix return value check in ERR_PTR()
  drm/msm: fix cmdstream size check
  drm/msm: hangcheck harder
  drm/msm: handle read vs write fences
  drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
  drm/i915: Use proper print format for debug prints
  ...

Pull block IO fixes from Jens Axboe:
 "After merge window, no new stuff this time only a collection of neatly
  confined and simple fixes"

* 'for-3.12/core' of git://git.kernel.dk/linux-block:
  cfq: explicitly use 64bit divide operation for 64bit arguments
  block: Add nr_bios to block_rq_remap tracepoint
  If the queue is dying then we only call the rq->end_io callout. This leaves bios setup on the request, because the caller assumes when the blk_execute_rq_nowait/blk_execute_rq call has completed that the rq->bios have been cleaned up.
  bio-integrity: Fix use of bs->bio_integrity_pool after free
  blkcg: relocate root_blkg setting and clearing
  block: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
  block: trace all devices plug operation

Pull btrfs fixes from Chris Mason:
 "These are mostly bug fixes and a two small performance fixes.  The
  most important of the bunch are Josef's fix for a snapshotting
  regression and Mark's update to fix compile problems on arm"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: create the uuid tree on remount rw
  btrfs: change extent-same to copy entire argument struct
  Btrfs: dir_inode_operations should use btrfs_update_time also
  btrfs: Add btrfs: prefix to kernel log output
  btrfs: refuse to remount read-write after abort
  Btrfs: btrfs_ioctl_default_subvol: Revert back to toplevel subvolume when arg is 0
  Btrfs: don't leak transaction in btrfs_sync_file()
  Btrfs: add the missing mutex unlock in write_all_supers()
  Btrfs: iput inode on allocation failure
  Btrfs: remove space_info->reservation_progress
  Btrfs: kill delay_iput arg to the wait_ordered functions
  Btrfs: fix worst case calculator for space usage
  Revert "Btrfs: rework the overcommit logic to be based on the total size"
  Btrfs: improve replacing nocow extents
  Btrfs: drop dir i_size when adding new names on replay
  Btrfs: replay dir_index items before other items
  Btrfs: check roots last log commit when checking if an inode has been logged
  Btrfs: actually log directory we are fsync()'ing
  Btrfs: actually limit the size of delalloc range
  Btrfs: allocate the free space by the existed max extent size when ENOSPC
  ...

'samples' is 64bit operant, but do_div() second parameter is 32.
do_div silently truncates high 32 bits and calculated result
is invalid.

In case if low 32bit of 'samples' are zeros then do_div() produces
kernel crash.
Signed-off-by: NAnatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Merge tag 'iio-fixes-for-3.12a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

Jonathan writes:

First round of IIO fixes for 3.12

A series of wrong 'struct dev' assumptions in suspend/resume callbacks
following on from this issue being identified in a new driver review.
One to watch out for in future.

A number of driver specific fixes
1) at91 - fix a overflow in clock rate computation
2) dummy - Kconfig dependency issue
3) isl29018 - uninitialized value
4) hmc5843 - measurement conversion bug introduced by recent cleanup.
5) ade7854-spi - wrong return value.

Some IIO core fixes
1) Wrong value picked up for event code creation for a modified channel
2) A null dereference on failure to initialize a buffer after no buffer has
   been in use, when using the available_scan_masks approach.
3) Sampling not stopped when a device is removed. Effects forced removal
   such as hot unplugging.
4) Prevent device going away if a chrdev is still open in userspace.
5) Prevent race on chardev opening and device being freed.
6) Add a missing iio_buffer_init in the call back buffer.

These last few are the first part of a set from Lars-Peter Clausen who
has been taking a closer look at our removal paths and buffer handling
than anyone has for quite some time.

Pull NFS client bugfix from Trond Myklebust:
 "Fix a regression due to incorrect sharing of gss auth caches"

* tag 'nfs-for-3.12-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  RPCSEC_GSS: fix crash on destroying gss auth

Adding the number of bios in a remapped request to 'block_rq_remap'
tracepoint.

Request remapper clones bios in a request to track the completion
status of each bio. So the number of bios can be useful information
for investigation.

Related discussions:
  http://www.redhat.com/archives/dm-devel/2013-August/msg00084.html
  http://www.redhat.com/archives/dm-devel/2013-September/msg00024.htmlSigned-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Users have been complaining of the uuid tree stuff warning that there is no uuid
root when trying to do snapshot operations.  This is because if you mount -o ro
we will not create the uuid tree.  But then if you mount -o rw,remount we will
still not create it and then any subsequent snapshot/subvol operations you try
to do will fail gloriously.  Fix this by creating the uuid_root on remount rw if
it was not already there.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

btrfs_ioctl_file_extent_same() uses __put_user_unaligned() to copy some data
back to it's argument struct. Unfortunately, not all architectures provide
__put_user_unaligned(), so compiles break on them if btrfs is selected.

Instead, just copy the whole struct in / out at the start and end of
operations, respectively.
Signed-off-by: NMark Fasheh <mfasheh@suse.de>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

Commit 2bc55652 (Btrfs: don't update atime on
RO subvolumes) ensures that the access time of an inode is not updated when
the inode lives in a read-only subvolume.
However, if a directory on a read-only subvolume is accessed, the atime is
updated. This results in a write operation to a read-only subvolume. I
believe that access times should never be updated on read-only subvolumes.

To reproduce:

 # mkfs.btrfs -f /dev/dm-3
 (...)
 # mount /dev/dm-3 /mnt
 # btrfs subvol create /mnt/sub
 	Create subvolume '/mnt/sub'
 # mkdir /mnt/sub/dir
 # echo "abc" > /mnt/sub/dir/file
 # btrfs subvol snapshot -r /mnt/sub /mnt/rosnap
 	Create a readonly snapshot of '/mnt/sub' in '/mnt/rosnap'
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:21:49.389157126 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
 # ls /mnt/rosnap/dir
 	file
 # stat /mnt/rosnap/dir
 	File: `/mnt/rosnap/dir'
 	Size: 8         Blocks: 0          IO Block: 4096   directory
 Device: 16h/22d    Inode: 257         Links: 1
 Access: (0755/drwxr-xr-x)  Uid: (    0/    root)   Gid: (    0/    root)
 	Access: 2013-09-11 07:22:56.797151670 -0400
 	Modify: 2013-09-11 07:22:02.330156079 -0400
 	Change: 2013-09-11 07:22:02.330156079 -0400
Reported-by: NKoen De Wit <koen.de.wit@oracle.com>
Signed-off-by: NGuangyu Sun <guangyu.sun@oracle.com>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

The kernel log entries for device label %s and device fsid %pU
are missing the btrfs: prefix. Add those here.
Signed-off-by: NFrank Holton <fholton@gmail.com>
Reviewed-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

It's still possible to flip the filesystem into RW mode after it's
remounted RO due to an abort. There are lots of places that check for
the superblock error bit and will not write data, but we should not let
the filesystem appear read-write.
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This patch makes it possible to set BTRFS_FS_TREE_OBJECTID as the default
subvolume by passing a subvolume id of 0.
Signed-off-by: Nchandan <chandan@linux.vnet.ibm.com>
Reviewed-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

In btrfs_sync_file(), if the call to btrfs_log_dentry_safe() returns
a negative error (for e.g. -ENOMEM via btrfs_log_inode()), we would
return without ending/freeing the transaction.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

The BUG() was replaced by btrfs_error() and return -EIO with the
patch "get rid of one BUG() in write_all_supers()", but the missing
mutex_unlock() was overlooked.

The 0-DAY kernel build service from Intel reported the missing
unlock which was found by the coccinelle tool:

    fs/btrfs/disk-io.c:3422:2-8: preceding lock on line 3374
Signed-off-by: NStefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

We don't do the iput when we fail to allocate our delayed delalloc work in
__start_delalloc_inodes, fix this.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This isn't used for anything anymore, just remove it.
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>

This is a left over of how we used to wait for ordered extents, which was to
grab the inode and then run filemap flush on it.  However if we have an ordered
extent then we already are holding a ref on the inode, and we just use
btrfs_start_ordered_extent anyway, so there is no reason to have an extra ref on
the inode to start work on the ordered extent.  Thanks,
Signed-off-by: NJosef Bacik <jbacik@fusionio.com>
Signed-off-by: NChris Mason <chris.mason@fusionio.com>