This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.

For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:

'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status

'ip link show'
show the setting status
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Don't populate the array tick_array on the stack but instead make it
static. Makes the object code smaller by 29 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  19191	    432	      0	  19623	   4ca7	hisilicon/hns3/hns3pf/hclge_tm.o

After:
   text	   data	    bss	    dec	    hex	filename
  19098	    496	      0	  19594	   4c8a	hisilicon/hns3/hns3pf/hclge_tm.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate the arrays port_map and sl_map on the stack but
instead make them static. Makes the object code smaller by 64 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  49575	   6872	     64	  56511	   dcbf	hisilicon/hns/hns_dsaf_main.o

After:
   text	   data	    bss	    dec	    hex	filename
  49350	   7032	     64	  56446	   dc7e	hisilicon/hns/hns_dsaf_main.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: NYizhuo <yzhai003@ucr.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.

Fixes: 57c5bc9a ("net: hisilicon: add hix5hd2 mac driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a spelling mistake in a .msg literal string. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds more information for reset DFX. Also, adds some
cleanups to reset info, move reset_fail_cnt into struct
hclge_rst_stats, and modifies some print formats.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch checks ops->set_default_reset_request whether is NULL
before using it in function hns3_slot_reset.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pfc_en and pfc_map need to be displayed in hexadecimal notation,
printing dma address should use %pad, and the end of printed string
needs to be add "\n".

This patch modifies them.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For hardware doesn't support use specified speed and duplex
to negotiate, it's unnecessary to check and modify the port
speed and duplex for fibre port when autoneg is on.

Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when hns3 driver configures the tm shaper to limit
bandwidth below 20Mbit using the parameters calculated by
hclge_shaper_para_calc(), the actual bandwidth limited by tm
hardware module is not accurate enough, for example, 1.28 Mbit
when the user is configuring 1 Mbit.

This patch adjusts the ir_calc to be closer to ir, and
always calculate the ir_b parameter when user is configuring
a small bandwidth. Also, removes an unnecessary parenthesis
when calculating denominator.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After setting new channel num, it needs free old ring memory and
allocate new ring memory. If there is no enough memory and allocate
new ring memory fail, the ring may initialize fail. To make sure
the network interface can work normally, driver should revert the
channel to the old configuration.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.set_channels support for HNS3 VF driver,
and updates related TQP information and RSS information, to support
modification of VF TQP number, and uses current rss_size instead of
max_rss_size to initialize RSS.

Also, fixes a format error in hclgevf_get_rss().
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate the array spec_opcode on the stack but instead make it
static const. Makes the object code smaller by 48 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
   6914	   1040	    128	   8082	   1f92	hns3/hns3vf/hclgevf_cmd.o

After:
   text	   data	    bss	    dec	    hex	filename
   6866	   1040	    128	   8034	   1f62	hns3/hns3vf/hclgevf_cmd.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_dbg_get_m7_info is used only in the hclge_debugfs.c,
so it should be declared with static.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the selftest and reset are performed at the same time, the loopback
setting may be still in the enable state after the reset. As a result,
packets cannot be sent out.

This patch fixes this issue by disabling loopback in hclge_mac_init.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unnecessary.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HNS3 driver can only unregister client which included in hnae3_client_list.
This patch adds the client node validity judgment.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since hclge_get_reset_level may return HNAE3_NONE_RESET,
so hdev->reset_level can not be assigned with the return
value in the hclge_reset(), otherwise, it will cause
the use of hdev->reset_level in hclge_reset_event get
into error.

Fixes: 012fcb52 ("net: hns3: activate reset timer when calling reset_event")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system will panic when change the ringparam in HNS3 drivers:

[ 1459.627727] hns3 0000:bd:00.0 eth6: Changing Tx/Rx ring ds from 1024/1024 to 24/24
[ 1459.635766] hns3 0000:bd:00.0 eth6: link down
[ 1459.640788] BUG: Bad page state in process ethtool  pfn:203f75c18
[ 1459.646940] page:ffff7ee4ffd70600 refcount:0 mapcount:0 mapping:ffff993fff40f400 index:0x0 compound_mapcount: 0
[ 1459.656987] flags: 0x9fffe00000010200(slab|head)
[ 1459.661591] raw: 9fffe00000010200 dead000000000100 dead000000000122 ffff993fff40f400
[ 1459.669302] raw: 0000000000000000 0000000080100010 00000000ffffffff 0000000000000000
[ 1459.677016] page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
[ 1459.683432] bad because of flags: 0x200(slab)
[ 1459.687775] Modules linked in: ib_ipoib ib_umad rpcrdma ib_iser libiscsi scsi_transport_iscsi hns_roce_hw_v2 crct10dif_ce hns3 ses hclge hnae3 hisi_hpre hisi_zip qm uacce ip_tables x_tables hisi_sas_v3_hw hisi_sas_main libsas scsi_transport_sas
[ 1459.709329] CPU: 14 PID: 17244 Comm: ethtool Tainted: G           O      5.3.0-rc4-00415-gc86f057 #1
[ 1459.718419] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B040.01 07/26/2019
[ 1459.727248] Call trace:
[ 1459.729688]  dump_backtrace+0x0/0x150
[ 1459.733335]  show_stack+0x24/0x30
[ 1459.736639]  dump_stack+0xa0/0xc4
[ 1459.739943]  bad_page+0xf0/0x158
[ 1459.743157]  free_pages_check_bad+0x84/0xa0
[ 1459.747322]  __free_pages_ok+0x348/0x378
[ 1459.751228]  page_frag_free+0x80/0x88
[ 1459.754877]  skb_free_head+0x38/0x48
[ 1459.758436]  skb_release_data+0x134/0x160
[ 1459.762427]  skb_release_all+0x30/0x40
[ 1459.766158]  consume_skb+0x38/0x108
[ 1459.769633]  __dev_kfree_skb_any+0x58/0x68
[ 1459.773718]  hns3_fini_ring+0x48/0x58 [hns3]
[ 1459.777970]  hns3_set_ringparam+0x2a8/0x418 [hns3]
[ 1459.782741]  dev_ethtool+0x5f4/0x2080
[ 1459.786390]  dev_ioctl+0x190/0x3d8
[ 1459.789777]  sock_do_ioctl+0xf8/0x220
[ 1459.793423]  sock_ioctl+0x3bc/0x490
[ 1459.796896]  do_vfs_ioctl+0xc4/0x868
[ 1459.800454]  ksys_ioctl+0x8c/0xa0
[ 1459.803752]  __arm64_sys_ioctl+0x28/0x38
[ 1459.807658]  el0_svc_common.constprop.0+0xe0/0x1e0
[ 1459.812426]  el0_svc_handler+0x34/0x90
[ 1459.816158]  el0_svc+0x10/0x14
[ 1459.819220] Disabling lock debugging due to kernel taint
[ 1459.825182] ------------[ cut here ]------------

Since ndo_stop will reclaim the RX's skb allocated by the driver,
so the backed up ring parameter should not keep this info.

Fixes: a723fb8e ("net: hns3: refine for set ring parameters")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In original codes, the VF index used incorrectly in function
hclge_set_vlan_rx_offload_cfg() and hclge_set_vlan_rx_offload_cfg().
When VF id is greater than 8, for example 9, it will set the
same bit with VF id 1.

This patch fixes it by using  vport->vport_id % HCLGE_VF_NUM_PER_CMD /
HCLGE_VF_NUM_PER_BYTE as the array index, instead of vport->vport_id /
HCLGE_VF_NUM_PER_CMD.

Fixes: 052ece6d ("net: hns3: add ethtool related offload command")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the static keyword to the front of declaration of g_dsaf_mode_match,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):

drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:27:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: NKrzysztof Wilczynski <kw@linux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
 variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 70a21490 ("net: hns3: reduce the parameters of some functions")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.

Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.

Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.

This patch also uses a macro to replace 0x1F.

Fixes: c39c4d98 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.

Fixes: 72e2fb07 ("net: hns3: clear reset interrupt status in hclge_irq_handle()")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the loopback test supports only mac selftest and serdes
selftest. This patch adds phy selftest.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When hardware or IMP get specified error it may need the client
to take some special operations.

This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch optimizes the waiting time for TQP reset.
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Reviewed-by: NYunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some incorrect type in assignment reported by sparse.
Those sparse warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : expected restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
- warning : cast to restricted __le16
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hclge_dcb.c, these pair of codes:
	hclge_notify_client(hdev, HNAE3_DOWN_CLIENT);
	hclge_notify_client(hdev, HNAE3_UNINIT_CLIENT);
and
	hclge_notify_client(hdev, HNAE3_INIT_CLIENT);
	hclge_notify_client(hdev, HNAE3_UP_CLIENT);
are called many times, so make them into a function.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Reviewed-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces kstrtouint()'s patameter base with 0 in the
hclge_dbg_dump_tm_mac(), which makes it more flexible. Also
uses a macro to replace string "dump tm map", since it has been
used multiple times.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses macro to replace some magic number.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For making the code more readable, this patch uses a array to
keep the information about the dumping register, and then uses
it to parse the parameter cmd_buf which passing into
hclge_dbg_dump_reg_cmd().

Also replaces parameter "base" of kstrtouint with 0 in the
hclge_dbg_dump_reg_common(), which makes it more flexible.
Signed-off-by: NZhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:542:30:
 warning: meta_data_key_info defined but not used [-Wunused-const-variable=]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h:553:30:
 warning: tuple_key_info defined but not used [-Wunused-const-variable=]

The two variable is only used in hclge_main.c,
so just move the definition over there.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>