This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.

For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:

'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status

'ip link show'
show the setting status
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Don't populate the array exp_mask on the stack but instead make it
static. Makes the object code smaller by 224 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  77832	   2290	      0	  80122	  138fa	ethernet/netronome/nfp/bpf/jit.o

After:
   text	   data	    bss	    dec	    hex	filename
  77544	   2354	      0	  79898	  1381a	ethernet/netronome/nfp/bpf/jit.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Throughout the driver there are several places where we wait
indefinitely for DPIO portal commands to be executed, while
the portal returns a busy response code.

Even though in theory we are guaranteed the portals become
available eventually, in practice the QBMan hardware module
may become unresponsive in various corner cases.

Make sure we can never get stuck in an infinite while loop
by adding a retry counter for all portal commands.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't print error message for a successful return value.

Fixes: d84c3a4d ("dpaa2-eth: Add new DPNI statistics counters")
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove one function call whose result was not used anywhere.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate the array tick_array on the stack but instead make it
static. Makes the object code smaller by 29 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  19191	    432	      0	  19623	   4ca7	hisilicon/hns3/hns3pf/hclge_tm.o

After:
   text	   data	    bss	    dec	    hex	filename
  19098	    496	      0	  19594	   4c8a	hisilicon/hns3/hns3pf/hclge_tm.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't populate the arrays port_map and sl_map on the stack but
instead make them static. Makes the object code smaller by 64 bytes.

Before:
   text	   data	    bss	    dec	    hex	filename
  49575	   6872	     64	  56511	   dcbf	hisilicon/hns/hns_dsaf_main.o

After:
   text	   data	    bss	    dec	    hex	filename
  49350	   7032	     64	  56446	   dc7e	hisilicon/hns/hns_dsaf_main.o

(gcc version 9.2.1, amd64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set channels callback enables the user to change the count of queues
used by the driver using ethtool. We decided to currently support only
equal number of rx and tx queues, this might change in the future.

Also rename dev_up to dev_was_up in ena_update_queue_count() to make
it clearer.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The number of queues can be derived using ethtool, no need to print
it in ena_probe()
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Update ena_ethtool:ena_get_channels() to return adapter->max_io_queues
  so that ethtool -l returns the correct maximum queue number.

- Change the name of ena_calc_io_queue_num() to
  ena_calc_max_io_queue_num() as it returns the maximum number of io
  queues and actual number of queues can be smaller if changed
  by ethtool -L which is implemented in a later commit.

- Change variable name from io_queue_num to max_num_io_queues in
  ena_calc_max_io_queue_num() and ena_probe().

- Make all types of variables that convey the number and sizeof queues
  to be u32, for consistency with the API between the driver and the
  device.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we use the same IRQ and NAPI to service RX and TX then we need to
use a combined channel instead of rx and tx channels.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Rename ena_calc_queue_size() to ena_calc_io_queue_size() for clarity
  and consistency
- Remove redundant number of io queues parameter in functions
  ena_enable_msix() and ena_enable_msix_and_set_admin_interrupts(),
  which already get adapter parameter, so use adapter->num_io_queues
  in the function instead.
- Use the local variable ena_dev instead of ctx->ena_dev in
  ena_calc_io_queue_size
- Fix multi row comment alignments
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most places in the code refer to the IO queues as io_queues and not
simply queues. Examples - max_io_queues_per_vf, ENA_MAX_NUM_IO_QUEUES,
ena_destroy_all_io_queues() etc..

We are also adding the new max_num_io_queues field to struct ena_adapter
in the following commit.

The changes included in this commit are:
struct ena_adapter->num_queues => struct ena_adapter->num_io_queues
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GMAC4+ cores support Layer 3 and Layer 4 filtering. Add the
corresponding callbacks in these cores.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two new tests for VLAN Perfect Filtering. While at it, increase a
little bit the tests strings lenght so that we can have more descriptive
test names.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If VLAN Hash Filtering is not available we can fallback to perfect
filtering instead. Let's implement this in XGMAC and GMAC cores and let
the user use this filter.

VLAN VID=0 always passes filter so we check if more than 2 VLANs are
created and return proper error code if so because perfect filtering
only supports 1 VID at a time.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add validation for FW version in order to prevent driver initialization
in case FW version is older than expected. FW version validation is
necessary, because use of a new field 'num_of_modules' in MGPIR register
is not backward compatible. FW 'minor' and 'subminor' versions are
expected to be greater than or equal to 2000 and 1886, respectively.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new API for FW "minor" and "subminor" version validation for
sharing it between "spectrum" and "minimal" drivers.
Use it in "spectrum" driver.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new field "num_of_modules" of MGPIR register for "thermal" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new field "num_of_modules" of MGPIR register for "hwmon" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.

Reading this info through MGPIR register is faster and does not depend
on possible dynamic re-configuration of ports.
In case of port dynamic re-configuration some modules can logically
"disappear" as a result of port split and un-spilt operations, which
can cause missing of some modules, in case this info is taken from port
to module mapping info.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend MGPIR - Management General Peripheral Information Register
with new field "num_of_modules" exposing the number of modules
supported by specific system.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tracing of device-related interaction to aid performance
analysis, especially around resync:

 tls:tls_device_offload_set
 tls:tls_device_rx_resync_send
 tls:tls_device_rx_resync_nh_schedule
 tls:tls_device_rx_resync_nh_delay
 tls:tls_device_tx_resync_req
 tls:tls_device_tx_resync_send
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ql_alloc_large_buffers, a new skb is allocated via netdev_alloc_skb.
This skb should be released if pci_dma_mapping_error fails.

Fixes: 0f8ab89e ("qla3xxx: Check return code from pci_map_single() in ql_release_to_lrg_buf_free_list(), ql_populate_free_queue(), ql_alloc_large_buffers(), and ql3xxx_send()")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When fetching free MSI-X vectors for ULDs, check for the error code
before accessing MSI-X info array. Otherwise, an out-of-bounds access is
attempted, which results in kernel panic.

Fixes: 94cdb8bb ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: NShahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: NVishal Kulkarni <vishal@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the devlink reaload the extack is present, so propagate it all
the way down to register_fib_notifier() call in spectrum_router.c.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creating netdevices for ports, put them under network namespace
that the core/parent devlink belongs to.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Follow-up patch is going to allow to reload devlink instance into
different network namespace, so use devlink_net() helper instead
of init_net.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if info->extack is NULL, mlxsw assumes that the event came
down from dump. Originally, the dump did not propagate the return value
back to the original caller (fib_notifier_register()). However, that is
now happening. So benefit from this and push the error up if it happened.
Remove rule cases in work handlers that are now dead code.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mlxsw distributes sent traffic among all the available send
queues. That includes control traffic as well as EMADs, which are used for
configuration of the device.

However because all the queues have the same traffic class of 3, they all
end up being directed to the same traffic class buffer. If the control
traffic in the buffer cannot be serviced quickly enough, the EMAD traffic
might be shut out, which causes transient failures, typically in FDB
maintenance, counter upkeep and other periodic work.

To address this issue, dedicate SDQ 0 to EMAD traffic, with TC 0.
Distribute the control traffic among the remaining queues, which are left
with their current TC 3.
Suggested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The address width of the controller can be read from hardware feature
registers much like on XGMAC. Add support for parsing the ADDR64 field
so that the DMA mask can be set accordingly.

This avoids getting swiotlb involved for DMA on Tegra186 and later.

Also make sure that the upper 32 bits of the DMA address are written to
the DMA descriptors when enhanced addressing mode is used. Similarily,
for each channel, the upper 32 bits of the DMA descriptor ring's base
address also need to be programmed to make sure the correct memory can
be fetched when the DMA descriptor ring is located beyond the 32-bit
boundary.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enhanced addressing mode is only required when more than 32 bits need to
be addressed. Add a DMA configuration parameter to enable this mode only
when needed.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stmmac driver will try to acquire its private mutex during suspend
via phylink_resolve() -> stmmac_mac_link_down() -> stmmac_eee_init().
However, the phylink configuration is updated with the private mutex
held already, which causes a deadlock during suspend.

Fix this by moving the phylink configuration updates out of the region
of code protected by the private mutex.

Fixes: 19e13cb2 ("net: stmmac: Hold rtnl lock in suspend/resume callbacks")
Suggested-by: NBitan Biswas <bbiswas@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recycling in mvpp2 has gone long time ago, but two comment still refers
to it. Remove those two misleading comments as they generate confusion.

Fixes: 7ef7e1d9 ("net: mvpp2: drop useless fields in mvpp2_bm_pool and related code")
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function mdio_sc_cfg_reg_write(), variable "reg_value" could be
uninitialized if regmap_read() fails. However, "reg_value" is used
to decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: NYizhuo <yzhai003@ucr.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>