The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Fixes: e7e197ed ("qmi_wwan: add support for the Dell Wireless 5821e module")
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.

To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return

Fixes: d9fe64e5 ("net: asix: Add in_pm parameter")
Signed-off-by: NAlexander Couzens <lynxis@fe80.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver can spam the kernel log with multiple messages of:

    net eth0: eth0: allmulti set

Usually 4 or 8 at a time (probably because of using ConnMan).

This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.

This patch was tested on Raspberry Pi 3B+

Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NFloris Bos <bos@je-eigen-domein.nl>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: NMatevz Vucnik <vucnikm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.

Fixes: d0cad871 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: NYuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.

Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.

Complete the implementation of this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.

Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: NDave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable.  usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.

So avoid the call to napi_disable in rtl8152_close when the device is
already gone.

The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.

By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code does:

 if (hrtimer_active(&t))
    hrtimer_cancel(&t);

However, hrtimer_cancel() checks if the timer is active, so the
test above is pointless.
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

        kzalloc(a * b, gfp)

with:
        kcalloc(a * b, gfp)

as well as handling cases of:

        kzalloc(a * b * c, gfp)

with:

        kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kzalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kzalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kzalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kzalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kzalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kzalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kzalloc(sizeof(THING) * C2, ...)
|
  kzalloc(sizeof(TYPE) * C2, ...)
|
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	E1 * E2
+	E1, E2
  , ...)
)
Signed-off-by: NKees Cook <keescook@chromium.org>

The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

        kmalloc(a * b, gfp)

with:
        kmalloc_array(a * b, gfp)

as well as handling cases of:

        kmalloc(a * b * c, gfp)

with:

        kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kmalloc(sizeof(THING) * C2, ...)
|
  kmalloc(sizeof(TYPE) * C2, ...)
|
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	E1 * E2
+	E1, E2
  , ...)
)
Signed-off-by: NKees Cook <keescook@chromium.org>

Commit 4a0e3e98 ("cdc_ncm: Add support for moving NDP to end
of NCM frame") added logic to reserve space for the NDP at the
end of the NTB/skb.  This reservation did not take the final
alignment of the NDP into account, causing us to reserve too
little space. Additionally the padding prior to NDP addition did
not ensure there was enough space for the NDP.

The NTB/skb with the NDP appended would then exceed the configured
max size. This caused the final padding of the NTB to use a
negative count, padding to almost INT_MAX, and resulting in:

[60103.825970] BUG: unable to handle kernel paging request at ffff9641f2004000
[60103.825998] IP: __memset+0x24/0x30
[60103.826001] PGD a6a06067 P4D a6a06067 PUD 4f65a063 PMD 72003063 PTE 0
[60103.826013] Oops: 0002 [#1] SMP NOPTI
[60103.826018] Modules linked in: (removed(
[60103.826158] CPU: 0 PID: 5990 Comm: Chrome_DevTools Tainted: G           O 4.14.0-3-amd64 #1 Debian 4.14.17-1
[60103.826162] Hardware name: LENOVO 20081 BIOS 41CN28WW(V2.04) 05/03/2012
[60103.826166] task: ffff964193484fc0 task.stack: ffffb2890137c000
[60103.826171] RIP: 0010:__memset+0x24/0x30
[60103.826174] RSP: 0000:ffff964316c03b68 EFLAGS: 00010216
[60103.826178] RAX: 0000000000000000 RBX: 00000000fffffffd RCX: 000000001ffa5000
[60103.826181] RDX: 0000000000000005 RSI: 0000000000000000 RDI: ffff9641f2003ffc
[60103.826184] RBP: ffff964192f6c800 R08: 00000000304d434e R09: ffff9641f1d2c004
[60103.826187] R10: 0000000000000002 R11: 00000000000005ae R12: ffff9642e6957a80
[60103.826190] R13: ffff964282ff2ee8 R14: 000000000000000d R15: ffff9642e4843900
[60103.826194] FS:  00007f395aaf6700(0000) GS:ffff964316c00000(0000) knlGS:0000000000000000
[60103.826197] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[60103.826200] CR2: ffff9641f2004000 CR3: 0000000013b0c000 CR4: 00000000000006f0
[60103.826204] Call Trace:
[60103.826212]  <IRQ>
[60103.826225]  cdc_ncm_fill_tx_frame+0x5e3/0x740 [cdc_ncm]
[60103.826236]  cdc_ncm_tx_fixup+0x57/0x70 [cdc_ncm]
[60103.826246]  usbnet_start_xmit+0x5d/0x710 [usbnet]
[60103.826254]  ? netif_skb_features+0x119/0x250
[60103.826259]  dev_hard_start_xmit+0xa1/0x200
[60103.826267]  sch_direct_xmit+0xf2/0x1b0
[60103.826273]  __dev_queue_xmit+0x5e3/0x7c0
[60103.826280]  ? ip_finish_output2+0x263/0x3c0
[60103.826284]  ip_finish_output2+0x263/0x3c0
[60103.826289]  ? ip_output+0x6c/0xe0
[60103.826293]  ip_output+0x6c/0xe0
[60103.826298]  ? ip_forward_options+0x1a0/0x1a0
[60103.826303]  tcp_transmit_skb+0x516/0x9b0
[60103.826309]  tcp_write_xmit+0x1aa/0xee0
[60103.826313]  ? sch_direct_xmit+0x71/0x1b0
[60103.826318]  tcp_tasklet_func+0x177/0x180
[60103.826325]  tasklet_action+0x5f/0x110
[60103.826332]  __do_softirq+0xde/0x2b3
[60103.826337]  irq_exit+0xae/0xb0
[60103.826342]  do_IRQ+0x81/0xd0
[60103.826347]  common_interrupt+0x98/0x98
[60103.826351]  </IRQ>
[60103.826355] RIP: 0033:0x7f397bdf2282
[60103.826358] RSP: 002b:00007f395aaf57d8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff6e
[60103.826362] RAX: 0000000000000000 RBX: 00002f07bc6d0900 RCX: 00007f39752d7fe7
[60103.826365] RDX: 0000000000000022 RSI: 0000000000000147 RDI: 00002f07baea02c0
[60103.826368] RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
[60103.826371] R10: 00000000ffffffff R11: 0000000000000000 R12: 00002f07baea02c0
[60103.826373] R13: 00002f07bba227a0 R14: 00002f07bc6d090c R15: 0000000000000000
[60103.826377] Code: 90 90 90 90 90 90 90 0f 1f 44 00 00 49 89 f9 48 89 d1 83
e2 07 48 c1 e9 03 40 0f b6 f6 48 b8 01 01 01 01 01 01 01 01 48 0f af c6 <f3> 48
ab 89 d1 f3 aa 4c 89 c8 c3 90 49 89 f9 40 88 f0 48 89 d1
[60103.826442] RIP: __memset+0x24/0x30 RSP: ffff964316c03b68
[60103.826444] CR2: ffff9641f2004000

Commit e1069bbf ("net: cdc_ncm: Reduce memory use when kernel
memory low") made this bug much more likely to trigger by reducing
the NTB size under memory pressure.

Link: https://bugs.debian.org/893393Reported-by: NГорбешко Богдан <bodqhrohro@gmail.com>
Reported-and-tested-by: NDennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Fixes: 4a0e3e98 ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Netgear Aircard 779S
Signed-off-by: NJosh Hill <josh@joshuajhill.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function.  The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.

Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID.  This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a77 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")

Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: NSebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of drivers have the following pattern:

if (np)
	of_mdiobus_register()
else
	mdiobus_register()

which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NFugang Duan <fugang.duan@nxp.com>
Reviewed-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function.  This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.

Fix by requiring the vendor-specific class for interface number
based matching.  Functions of other classes can and should use
class based matching instead.

Fixes: 03304bcb ("net: qmi_wwan: use fixed interface number matching")
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify the error messages when phy registration fails.
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove driver version info from the lan78xx driver.
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding Fixed PHY support to the lan78xx driver.
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for PID 0x90b2 of ublox R410M.

qmicli -d /dev/cdc-wdm0 --dms-get-manufacturer
[/dev/cdc-wdm0] Device manufacturer retrieved:
        Manufacturer: 'u-blox'

qmicli -d /dev/cdc-wdm0 --dms-get-model
[/dev/cdc-wdm0] Device model retrieved:
        Model: 'SARA-R410M-02B'
Signed-off-by: NSZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to dump lan78xx family registers using ethtool, add
support at lan78xx driver level.
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:

    0=link/activity          1=link1000/activity
    2=link100/activity       3=link10/activity
    4=link100/1000/activity  5=link10/1000/activity
    6=link10/100/activity    14=off    15=on

These values are given symbolic constants in a dt-bindings header.

Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-960 router.
The oem configuration states:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1435 ProdID=d191 Rev=ff.ff
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=88(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: NPawel Dembicki <paweldembicki@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 92571a1a ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.

Fix this issue by removing the lan78xx_reset call from lan78xx_open.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.

The modem is controlled via AT commands through the exposed TTYs.

AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: NBassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx_defer_event generates an error message whenever the work item
is already scheduled. lan78xx_open defers three events -
EVENT_STAT_UPDATE, EVENT_DEV_OPEN and EVENT_LINK_RESET. Being aware
of the likelihood (or certainty) of an error message, the DEV_OPEN
event is added to the set of pending events directly, relying on
the subsequent deferral of the EVENT_LINK_RESET call to schedule the
work.  Take the same precaution with EVENT_STAT_UPDATE to avoid a
totally unnecessary error message.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx_read_otp tries to return -EINVAL in the event of invalid OTP
content, but the value gets overwritten before it is returned and the
read goes ahead anyway. Make the read conditional as it should be
and preserve the error code.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using wicked with a lan78xx device attached to the system, we
end up with ethtool commands issued on the device before an ifup
got issued. That lead to the following crash:

    Unable to handle kernel NULL pointer dereference at virtual address 0000039c
    pgd = ffff800035b30000
    [0000039c] *pgd=0000000000000000
    Internal error: Oops: 96000004 [#1] SMP
    Modules linked in: [...]
    Supported: Yes
    CPU: 3 PID: 638 Comm: wickedd Tainted: G            E      4.12.14-0-default #1
    Hardware name: raspberrypi rpi/rpi, BIOS 2018.03-rc2 02/21/2018
    task: ffff800035e74180 task.stack: ffff800036718000
    PC is at phy_ethtool_ksettings_get+0x20/0x98
    LR is at lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
    pc : [<ffff0000086f7f30>] lr : [<ffff000000dcca84>] pstate: 20000005
    sp : ffff80003671bb20
    x29: ffff80003671bb20 x28: ffff800035e74180
    x27: ffff000008912000 x26: 000000000000001d
    x25: 0000000000000124 x24: ffff000008f74d00
    x23: 0000004000114809 x22: 0000000000000000
    x21: ffff80003671bbd0 x20: 0000000000000000
    x19: ffff80003671bbd0 x18: 000000000000040d
    x17: 0000000000000001 x16: 0000000000000000
    x15: 0000000000000000 x14: ffffffffffffffff
    x13: 0000000000000000 x12: 0000000000000020
    x11: 0101010101010101 x10: fefefefefefefeff
    x9 : 7f7f7f7f7f7f7f7f x8 : fefefeff31677364
    x7 : 0000000080808080 x6 : ffff80003671bc9c
    x5 : ffff80003671b9f8 x4 : ffff80002c296190
    x3 : 0000000000000000 x2 : 0000000000000000
    x1 : ffff80003671bbd0 x0 : ffff80003671bc00
    Process wickedd (pid: 638, stack limit = 0xffff800036718000)
    Call trace:
    Exception stack(0xffff80003671b9e0 to 0xffff80003671bb20)
    b9e0: ffff80003671bc00 ffff80003671bbd0 0000000000000000 0000000000000000
    ba00: ffff80002c296190 ffff80003671b9f8 ffff80003671bc9c 0000000080808080
    ba20: fefefeff31677364 7f7f7f7f7f7f7f7f fefefefefefefeff 0101010101010101
    ba40: 0000000000000020 0000000000000000 ffffffffffffffff 0000000000000000
    ba60: 0000000000000000 0000000000000001 000000000000040d ffff80003671bbd0
    ba80: 0000000000000000 ffff80003671bbd0 0000000000000000 0000004000114809
    baa0: ffff000008f74d00 0000000000000124 000000000000001d ffff000008912000
    bac0: ffff800035e74180 ffff80003671bb20 ffff000000dcca84 ffff80003671bb20
    bae0: ffff0000086f7f30 0000000020000005 ffff80002c296000 ffff800035223900
    bb00: 0000ffffffffffff 0000000000000000 ffff80003671bb20 ffff0000086f7f30
    [<ffff0000086f7f30>] phy_ethtool_ksettings_get+0x20/0x98
    [<ffff000000dcca84>] lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
    [<ffff0000087cbc40>] ethtool_get_settings+0x68/0x210
    [<ffff0000087cc0d4>] dev_ethtool+0x214/0x2180
    [<ffff0000087e5008>] dev_ioctl+0x400/0x630
    [<ffff00000879dd00>] sock_do_ioctl+0x70/0x88
    [<ffff00000879f5f8>] sock_ioctl+0x208/0x368
    [<ffff0000082cde10>] do_vfs_ioctl+0xb0/0x848
    [<ffff0000082ce634>] SyS_ioctl+0x8c/0xa8
    Exception stack(0xffff80003671bec0 to 0xffff80003671c000)
    bec0: 0000000000000009 0000000000008946 0000fffff4e841d0 0000aa0032687465
    bee0: 0000aaaafa2319d4 0000fffff4e841d4 0000000032687465 0000000032687465
    bf00: 000000000000001d 7f7fff7f7f7f7f7f 72606b622e71ff4c 7f7f7f7f7f7f7f7f
    bf20: 0101010101010101 0000000000000020 ffffffffffffffff 0000ffff7f510c68
    bf40: 0000ffff7f6a9d18 0000ffff7f44ce30 000000000000040d 0000ffff7f6f98f0
    bf60: 0000fffff4e842c0 0000000000000001 0000aaaafa2c2e00 0000ffff7f6ab000
    bf80: 0000fffff4e842c0 0000ffff7f62a000 0000aaaafa2b9f20 0000aaaafa2c2e00
    bfa0: 0000fffff4e84818 0000fffff4e841a0 0000ffff7f5ad0cc 0000fffff4e841a0
    bfc0: 0000ffff7f44ce3c 0000000080000000 0000000000000009 000000000000001d
    bfe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000

The culprit is quite simple: The driver tries to access the phy left and right,
but only actually has a working reference to it when the device is up.

The fix thus is quite simple too: Get a reference to the phy on probe already
and keep it even when the device is going down.

With this patch applied, I can successfully run wicked on my system and bring
the interface up and down as many times as I want, without getting NULL pointer
dereferences in between.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit cf29bded.

It causes regressions.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.

Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.

Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NRaghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This modem is embedded on dlink dwr-921 router.
    The oem configuration states:

    T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 0
    D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
    P:  Vendor=1435 ProdID=0918 Rev= 2.32
    S:  Manufacturer=Android
    S:  Product=Android
    S:  SerialNumber=0123456789ABCDEF
    C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
    I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
    E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
    E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
    E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
    E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
    E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    I:* If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
    E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
    E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Tested on openwrt distribution
Signed-off-by: NGiuseppe Lippolis <giu.lippolis@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to support the modem found in HP EliteBook 820 G3.
Signed-off-by: NTorsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
The USB id is added to qmi_wwan.c to allow QMI communication with
the BM806U.

Tested on 4.14 kernel and OpenWRT.
Signed-off-by: NPawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefer the direct use of octal for permissions.

Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.

Miscellanea:

o Whitespace neatening around these conversions.
Signed-off-by: NJoe Perches <joe@perches.com>
Reviewed-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>