When LFA is enabled, we don't reset the phy. But EEE settings changes
don't take effect until the phy is reset. Add a phy reset when we detect
a changed EEE setting.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Normally on driver load, we set the default settings for speed and flow
control. However, if the default setting is not compatible with the current link
state, we would autonegotiate and cause a link flap. To avoid this, we
pull the current advertised settings into the config.

A second scenario is if a user changes the speed/duplex/fc settings when
the interface is down. In this case we must not pull the settings from
the phy and overwrite user settings. We avoid that by checking the
USER_CONFIGURED flag.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch and the following two patches add support for link flap avoidance
by maintaining the link on power down. This feature is required for
management capable devices to have the management connection
uninterrupted on driver reload, reboot and interface up/down.

The other pros of this feature are
 - It speeds up boot up time by several seconds as DHCP addresses can be
   acquired faster.
 - It avoids lengthy Spanning Tree delay.

On powerup the hardware brings up the phy with default settings. If the
link is not up, the management software configures the phy to gigabit
and starts autonegotiate. Subsequently, as long as the link is up, the
driver and management refrain from resetting and/or changing any
configuration that the link depends on.

The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
disabled by default.  If this setting is enabled, we skip powering down
the phy and resetting it.

A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
support for gigabit link speed when device is on auxiliary power.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor for use in the next patch that adds sgmii phy support.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.

Add a warning in these cases.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting.  If flow control does not match, a relink is not necessary as
flow control is not a PHY setting.  Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move mutex initialization by allocation of the mailbox it protects.

introduced in commit 1d6f3cd8 'bnx2x: Prevent VF race'
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 184b8904 ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.

Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.

http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdfSigned-off-by: NKees Cook <keescook@chromium.org>
Reported-by: NOded Horovitz <oded@privatecore.com>
Reported-by: NBrad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make few alignments, comment fixes and debug messages.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add full support for "ethtool -m" command.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mail box containing the Vf-Pf messages is susceptible
to a race - it's possible for 2 flows to try and write commands,
causing one to override the other's message.
Use a mutex to synchronize the access, preventing said race.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Outer vlan removal in VF queues was made according to the VF's
multi-function mode (which is never set).
Instead, the PF's multi-function mode should be used to determine
if outer vlan removal is needed.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a VF performs load/unload its statistics become corrupt -
we now zero the statistics structures upon a VF device load.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ARI forwarding flag is missing from the PCI bridge, remove SR-IOV
support instead of failing the probe process.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 7fa6f340 "AER revised" erroneously inserted an error-flow
in which a semaphore is released even though the attempt to take it
has failed.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

57712/578xx devices during handling of encapsulated TSO can
properly increase ip id for only one ip header.
The patch selects inner header to be increased.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Maciej Zenczykowski <maze@google.com>
CC: Jesse Gross <jesse@nicira.com>
Reported-by: NEric Dumazet <edumazet@google.com>
Tested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Revised bnx2x implementation of PCI Express Advanced Error Recovery -
stop and free driver resources according to the AER flow (instead of the
currently implemented `hope-for-the-best' release approach), and do not make
any assumptions on the HW state after slot reset.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The UPDATE_QSTAT function introduced on February 15, 2012
in commit 1355b704 "bnx2x: consistent statistics after
internal driver reload" incorrectly fails to handle overflow
during addition of the lower 32-bit field of a stat.

This bug is present since 3.4-rc1 and should thus be considered
a candidate for stable 3.4+ releases.

Google-Bug-Id: 8374428
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Cc: Mintz Yuval <yuvalmin@broadcom.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch drives FW to perform RSS for GRE traffic,
based on inner headers.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch utilizes FW offload capabilities for
encapsulation protocols.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the number of calls required to alloc
a zeroed block of memory.

Trivially reduces overall object size.

Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the hardware initialization fails in bnx2x_nic_load() after adding
napi objects, they would not be deleted. A subsequent attempt to unload
the bnx2x module detects a corruption in the napi list.

Add the missing napi deletion to the error path.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d13ba512 ("tg3: Remove
SPEED_UNKNOWN checks") cleaned up the autoneg advertisement by
removing some dead code. One effect of this change was that the
advertisement register would not be updated if autoneg is turned off.

This exposed a bug on the 5715 device w.r.t linking. The 5715 defaults
to advertise only 10Mb Full duplex. But with autoneg disabled, it needs
the configured speed enabled in the advertisement register to link up.

This patch adds the work around to advertise all speeds on the 5715 when
autoneg is disabled.
Reported-by: NMarcin Miotk <marcinmiotk81@gmail.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using list_move() instead of list_del() + list_add().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x FW 1.78.17 properly supports DCBX configuration for 4-port devices,
enabling FCoE support on 57840 boards.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Support sysfs interface for getting the maximal number of virtual functions
   of a given physical function.
2. Support sysfs interface for getting and setting the current number of
   virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.

This patch prevents said message.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>