ixgb fails to work after reload on recent kernels:

rmmod ixgb (dev->current_state = PCI_UNKNOWN)
modprobe ixgb (pci_enable_device will bail leaving current_state to PCI_UNKNOWN)
ifup eth0
do_IRQ: 2.82 No irq handler for vector (irq -1)

The issue was exposed by commit fcd097f3
PCI: MSI: Remove unsafe and unnecessary hardware access

which avoids HW writes for power states != PCI_D0

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DCB credits refill quantum _must_ be greater than half the max
packet size. This is needed to guarantee that TX DMA operations
are not attempted during a pause state. Additionally, the min IFG
must be set correctly for DCB mode. If a DMA operation is
requested unexpectedly during the pause state the HW data
store may be corrupted leading to a DMA hang.  The DMA hang
requires a reset to correct. This fixes the HW configuration
to avoid this condition.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some parts need to execute resets during normal operation.  This flag
check ensures that those parts reset without needlessly alarming the
user.  Other unexpected resets by other parts will dump debug info
and message the reset action to the user, as originally intended.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Acked-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some errors can be induced in the PHY via environmental testing
(specifically extreme temperature changes and electro static
discharge testing), and in the case of the PHY hanging due to
this input, this detects the problem and resets to continue.
This issue only applies to 82574 silicon.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit eab6d18d "vlan: Don't check for vlan group before
vlan_tx_tag_present" removed the need for the adapter variable
in igb_xmit_frame_ring_adv().  This removes the variable as well
to avoid the compiler warning.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(Applied over Eric's "ehea: fix use after free" patch)

Currently ehea stats are broken. The bytes counters are got from
the hardware, while the packets counters are got from the device
driver. Also, the device driver counters are resetted during the
the down process, and the hardware aren't, causing some weird
numbers.

This patch just consolidates the packets and bytes on the device
driver.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix lockdep warning:
[   52.991402] ======================================================
[   52.991511] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
[   52.991569] 2.6.36-04573-g4b60626-dirty #65
[   52.991622] ------------------------------------------------------
[   52.991696] ip/4842 [HC0[0]:SC0[4]:HE1:SE0] is trying to acquire:
[   52.991758]  (&bond->lock){++++..}, at: [<efe4d300>] bond_set_multicast_list+0x60/0x2c0 [bonding]
[   52.991966]
[   52.991967] and this task is already holding:
[   52.992008]  (&bonding_netdev_addr_lock_key){+.....}, at: [<c04e5530>] dev_mc_sync+0x50/0xa0
[   52.992008] which would create a new lock dependency:
[   52.992008]  (&bonding_netdev_addr_lock_key){+.....} -> (&bond->lock){++++..}
[   52.992008]
[   52.992008] but this new dependency connects a SOFTIRQ-irq-safe lock:
[   52.992008]  (&(&mc->mca_lock)->rlock){+.-...}
[   52.992008] ... which became SOFTIRQ-irq-safe at:
[   52.992008]   [<c0272beb>] __lock_acquire+0x96b/0x1960
[   52.992008]   [<c027415e>] lock_acquire+0x7e/0xf0
[   52.992008]   [<c05f356d>] _raw_spin_lock_bh+0x3d/0x50
[   52.992008]   [<c0584e40>] mld_ifc_timer_expire+0xf0/0x280
[   52.992008]   [<c024cee6>] run_timer_softirq+0x146/0x310
[   52.992008]   [<c024591d>] __do_softirq+0xad/0x1c0
[   52.992008]
[   52.992008] to a SOFTIRQ-irq-unsafe lock:
[   52.992008]  (&bond->lock){++++..}
[   52.992008] ... which became SOFTIRQ-irq-unsafe at:
[   52.992008] ...  [<c0272c3b>] __lock_acquire+0x9bb/0x1960
[   52.992008]   [<c027415e>] lock_acquire+0x7e/0xf0
[   52.992008]   [<c05f36b8>] _raw_write_lock+0x38/0x50
[   52.992008]   [<efe4cbe4>] bond_vlan_rx_register+0x24/0x70 [bonding]
[   52.992008]   [<c0598010>] register_vlan_dev+0xc0/0x280
[   52.992008]   [<c0599f3a>] vlan_newlink+0xaa/0xd0
[   52.992008]   [<c04ed4b4>] rtnl_newlink+0x404/0x490
[   52.992008]   [<c04ece35>] rtnetlink_rcv_msg+0x1e5/0x220
[   52.992008]   [<c050424e>] netlink_rcv_skb+0x8e/0xb0
[   52.992008]   [<c04ecbac>] rtnetlink_rcv+0x1c/0x30
[   52.992008]   [<c0503bfb>] netlink_unicast+0x24b/0x290
[   52.992008]   [<c0503e37>] netlink_sendmsg+0x1f7/0x310
[   52.992008]   [<c04cd41c>] sock_sendmsg+0xac/0xe0
[   52.992008]   [<c04ceb80>] sys_sendmsg+0x130/0x230
[   52.992008]   [<c04cf04e>] sys_socketcall+0xde/0x280
[   52.992008]   [<c0202d10>] sysenter_do_call+0x12/0x36
[   52.992008]
[   52.992008] other info that might help us debug this:
...
[ Full info at netdev: Wed, 27 Oct 2010 12:24:30 +0200
  Subject: [BUG net-2.6 vlan/bonding] lockdep splats ]

Use BH variant of write_lock(&bond->lock) (as elsewhere in bond_main)
to prevent this dependency.

Fixes commit f35188fa [v2.6.36]
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>

After making rcu protection for tunnels (ipip, gre, sit and ip6) a bug
was introduced into the SIOCCHGTUNNEL code.

The tunnel is first unlinked, then addresses change, then it is linked
back probably into another bucket. But while changing the parms, the
hash table is unlocked to readers and they can lookup the improper tunnel.

Respective commits are b7285b79 (ipip: get rid of ipip_lock), 1507850b
(gre: get rid of ipgre_lock), 3a43be3c (sit: get rid of ipip6_lock) and
94767632 (ip6tnl: get rid of ip6_tnl_lock).

The quick fix is to wait for quiescent state to pass after unlinking,
but if it is inappropriate I can invent something better, just let me
know.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete successive assignments to the same location.  In the first case, the
hscx array has two elements, so change the assignment to initialize the
second one.  In the second case, the two assignments are simply identical.
Furthermore, neither is necessary, because the effect of the assignment is
only visible in the next line, in the assignment in the if test.  The patch
inlines the right hand side value in the latter assignment and pulls that
assignment out of the if test.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete successive assignments to the same location.  The current definition
does not initialize the respRing structure, which has the same type as the
cmdRing structure, so initialize that one instead.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Acked-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The other code around these duplicated assignments initializes the 0 1 2
and 3 elements of an array, so change the initialization of the
rx_session_id array to do the same.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression i;
@@

*i = ...;
 i = ...;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

4095 vlan id is reserved and should not be use.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If eswitch is enabled, rcv ring size can be reduce, as
physical port is partition-ed.
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In failover bonding case, same mac address can be programmed on other slave function.
Fw will delete old entry (original func) associated with that mac address.
Need to reporgram mac address, if failover again happen to original function.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ehea_start_xmit() dereferences skb after its freeing in ehea_xmit3() to
get vlan tags.

Move the offending block before the potential ehea_xmit3() call.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds __rcu annotations to inetpeer
	(struct inet_peer)->avl_left
	(struct inet_peer)->avl_right

This is a tedious cleanup, but removes one smp_wmb() from link_to_pool()
since we now use more self documenting rcu_assign_pointer().

Note the use of RCU_INIT_POINTER() instead of rcu_assign_pointer() in
all cases we dont need a memory barrier.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds __rcu annotation to (struct fib_rule)->ctarget
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotations to :
        (struct ip_tunnel)->prl
        (struct ip_tunnel_prl_entry)->next
        (struct xfrm_tunnel)->next
	struct xfrm_tunnel *tunnel4_handlers
	struct xfrm_tunnel *tunnel64_handlers

And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotations to :
        struct net_protocol *inet_protos
        struct net_protocol *inet6_protos

And use appropriate casts to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add __rcu annotations to :
        (struct dst_entry)->rt_next
        (struct rt_hash_bucket)->chain

And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When async mcc compls are rcvd on an i/f that is down (and so interrupts are disabled)
they just lie unprocessed in the compl queue.The compl queue can eventually get filled
up and cause the BE to lock up.The fix is to use be_worker to reap mcc compls when the
i/f is down.be_worker is now launched in be_probe() and canceled in be_remove().
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After running this bonding setup script
    modprobe bonding miimon=100 mode=0 max_bonds=1
    ifconfig bond0 10.1.1.1/16
    ifenslave bond0 eth1
    ifenslave bond0 eth3
on s390 with qeth-driven slaves, modprobe -r fails with this message
    unregister_netdevice: waiting for bond0 to become free. Usage count = 1
due to twice detection of duplicate address.
Problem is caused by a missing decrease of ifp->refcnt in addrconf_dad_failure.
An extra call of in6_ifa_put(ifp) solves it.
Problem has been introduced with commit f2344a13.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_HW_CSUM indicates the ability to update an TCP/IP-style 16-bit
checksum with the checksum of an arbitrary part of the packet data,
whereas the FCoE CRC is something entirely different.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_can_checksum() incorrectly returns true in these cases:

1. The skb has both out-of-band and in-band VLAN tags and the device
   supports checksum offload for the encapsulated protocol but only with
   one layer of encapsulation.
2. The skb has a VLAN tag and the device supports generic checksumming
   but not in conjunction with VLAN encapsulation.

Rearrange the VLAN tag checks to avoid these.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gianfar: Fix crashes on RX path (Was Re: [Bugme-new] [Bug 19692] New: linux-2.6.36-rc5 crash with gianfar ethernet at full line rate traffic)

The rx_recycle queue is global per device but can be accesed by many
napi handlers at the same time, so it needs full skb_queue primitives
(with locking). Otherwise, various crashes caused by broken skbs are
possible.

This patch resolves, at least partly, bugzilla bug 19692. (Because of
some doubts that there could be still something around which is hard
to reproduce my proposal is to leave this bug opened for a month.)

Fixes commit: 0fd56bb5 ("gianfar: Add
support for skb recycling")
Reported-by: Nemin ak <eminak71@gmail.com>
Tested-by: Nemin ak <eminak71@gmail.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a bug in the interaction between ipv6_create_tempaddr and
addrconf_verify.  Because ipv6_create_tempaddr uses the cstamp and tstamp
from the public address in creating a private address, if we have not
received a router advertisement in a while, tstamp + temp_valid_lft might be
< now.  If this happens, the new address is created inside
ipv6_create_tempaddr, then the loop within addrconf_verify starts again and
the address is immediately deleted.  We are left with no temporary addresses
on the interface, and no more will be created until the public IP address is
updated.  To avoid this, set the expiry time to be the minimum of the time
left on the public address or the config option PLUS the current age of the
public interface.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If privacy extentions are enabled, but no current temporary address exists,
then create one when we get a router advertisement.
Signed-off-by: NGlenn Wurster <gwurster@scs.carleton.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While fixing CONFIG_SPARSE_RCU_POINTER errors, I had to fix accesses to
fz->fz_hash for real.

-	&fz->fz_hash[fn_hash(f->fn_key, fz)]
+	rcu_dereference(fz->fz_hash) + fn_hash(f->fn_key, fz)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some panic reports in fib_rules_lookup() show a rule could have a NULL
pointer as a next pointer in the rules_list.

This can actually happen because of a bug in fib_nl_newrule() : It
checks if current rule is the destination of unresolved gotos. (Other
rules have gotos to this about to be inserted rule)

Problem is it does the resolution of the gotos before the rule is
inserted in the rules_list (and has a valid next pointer)

Fix this by moving the rules_list insertion before the changes on gotos.

A lockless reader can not any more follow a ctarget pointer, unless
destination is ready (has a valid next pointer)
Reported-by: NOleg A. Arkhangelsky <sysoleg@yandex.ru>
Reported-by: NJoe Buehler <aspam@cox.net>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver calls device_set_wakeup_enable() under spin_lock_bh,
which causes a problem to happen after the recent core power
management changes, because this function can sleep now.  Fix this
by moving the device_set_wakeup_enable() call out of the
spin_lock_bh-protected area.
Reported-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets the missing CAN_RTR_FLAG if a standard RTR frame is
received.
(For extended frames the CAN_RTR_FLAG was already set correctly.)
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The priv is part of the memory allocated by alloc_candev().
This patch moved the free it after last usage of priv.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>