Firmware is unable to retain the port counters during any kind of
fatal or non-fatal resets, so we must clear the port counters to
avoid false detection of port counter overflow.

Fixes: fea6b333 ("bnxt_en: Accumulate all counters.")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The module eeprom address range returned by bnxt_get_module_eeprom()
should be 256 bytes of A0h address space, the lower half of the A2h
address space, and page 0 for the upper half of the A2h address space.

Fix the firmware call by passing page_number 0 for the A2h slave address
space.

Fixes: 42ee18fe ("bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO")
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.

However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it.  In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.

Fixes: b340dc68 ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

bnxt_open_nic() is called during configuration changes that require
the NIC to be closed and then opened.  This call is protected by
rtnl_lock.  Firmware reset can be happening at the same time.  Only
critical portions of the entire firmware reset sequence are protected
by the rtnl_lock.  It is possible that bnxt_open_nic() can be called
when the firmware reset sequence is aborting.  In that case,
bnxt_open_nic() needs to check if the ABORT_ERR flag is set and
abort if it is.  The configuration change that resulted in the
bnxt_open_nic() call will fail but the NIC will be brought to a
consistent IF_DOWN state.

Without this patch, if bnxt_open_nic() were to continue in this error
state, it may crash like this:

[ 1648.659736] BUG: unable to handle kernel NULL pointer dereference at           (null)
[ 1648.659768] IP: [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.659796] PGD 101e1b3067 PUD 101e1b2067 PMD 0
[ 1648.659813] Oops: 0000 [#1] SMP
[ 1648.659825] Modules linked in: xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc dell_smbios dell_wmi_descriptor dcdbas amd64_edac_mod edac_mce_amd kvm_amd kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper vfat cryptd fat pcspkr ipmi_ssif sg k10temp i2c_piix4 wmi ipmi_si ipmi_devintf ipmi_msghandler tpm_crb acpi_power_meter sch_fq_codel ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm ahci drm libahci megaraid_sas crct10dif_pclmul crct10dif_common
[ 1648.660063]  tg3 libata crc32c_intel bnxt_en(OE) drm_panel_orientation_quirks devlink ptp pps_core dm_mirror dm_region_hash dm_log dm_mod fuse
[ 1648.660105] CPU: 13 PID: 3867 Comm: ethtool Kdump: loaded Tainted: G           OE  ------------   3.10.0-1152.el7.x86_64 #1
[ 1648.660911] Hardware name: Dell Inc. PowerEdge R7515/0R4CNN, BIOS 1.2.14 01/28/2020
[ 1648.661662] task: ffff94e64cbc9080 ti: ffff94f55df1c000 task.ti: ffff94f55df1c000
[ 1648.662409] RIP: 0010:[<ffffffffc01e9b3a>]  [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.663171] RSP: 0018:ffff94f55df1fba8  EFLAGS: 00010202
[ 1648.663927] RAX: 0000000000000000 RBX: ffff94e6827e0000 RCX: 0000000000000000
[ 1648.664684] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff94e6827e08c0
[ 1648.665433] RBP: ffff94f55df1fc20 R08: 00000000000001ff R09: 0000000000000008
[ 1648.666184] R10: 0000000000000d53 R11: ffff94f55df1f7ce R12: ffff94e6827e08c0
[ 1648.666940] R13: ffff94e6827e08c0 R14: ffff94e6827e08c0 R15: ffffffffb9115e40
[ 1648.667695] FS:  00007f8aadba5740(0000) GS:ffff94f57eb40000(0000) knlGS:0000000000000000
[ 1648.668447] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1648.669202] CR2: 0000000000000000 CR3: 0000001022772000 CR4: 0000000000340fe0
[ 1648.669966] Call Trace:
[ 1648.670730]  [<ffffffffc01f1d5d>] ? bnxt_need_reserve_rings+0x9d/0x170 [bnxt_en]
[ 1648.671496]  [<ffffffffc01fa7ea>] __bnxt_open_nic+0x8a/0x9a0 [bnxt_en]
[ 1648.672263]  [<ffffffffc01f7479>] ? bnxt_close_nic+0x59/0x1b0 [bnxt_en]
[ 1648.673031]  [<ffffffffc01fb11b>] bnxt_open_nic+0x1b/0x50 [bnxt_en]
[ 1648.673793]  [<ffffffffc020037c>] bnxt_set_ringparam+0x6c/0xa0 [bnxt_en]
[ 1648.674550]  [<ffffffffb8a5f564>] dev_ethtool+0x1334/0x21a0
[ 1648.675306]  [<ffffffffb8a719ff>] dev_ioctl+0x1ef/0x5f0
[ 1648.676061]  [<ffffffffb8a324bd>] sock_do_ioctl+0x4d/0x60
[ 1648.676810]  [<ffffffffb8a326bb>] sock_ioctl+0x1eb/0x2d0
[ 1648.677548]  [<ffffffffb8663230>] do_vfs_ioctl+0x3a0/0x5b0
[ 1648.678282]  [<ffffffffb8b8e678>] ? __do_page_fault+0x238/0x500
[ 1648.679016]  [<ffffffffb86634e1>] SyS_ioctl+0xa1/0xc0
[ 1648.679745]  [<ffffffffb8b93f92>] system_call_fastpath+0x25/0x2a
[ 1648.680461] Code: 9e 60 01 00 00 0f 1f 40 00 45 8b 8e 48 01 00 00 31 c9 45 85 c9 0f 8e 73 01 00 00 66 0f 1f 44 00 00 49 8b 86 a8 00 00 00 48 63 d1 <48> 8b 14 d0 48 85 d2 0f 84 46 01 00 00 41 8b 86 44 01 00 00 c7
[ 1648.681986] RIP  [<ffffffffc01e9b3a>] bnxt_alloc_mem+0x50a/0x1140 [bnxt_en]
[ 1648.682724]  RSP <ffff94f55df1fba8>
[ 1648.683451] CR2: 0000000000000000

Fixes: ec5d31e3 ("bnxt_en: Handle firmware reset status during IF_UP.")
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.

pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid.  So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses.  These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.

Fixes: 6316ea6d ("bnxt_en: Enable AER support.")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

As part of the commit b148bb23
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.

As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.

Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().

Fixes: b148bb23 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one().  This caused a
regression because the workqueue can be restarted if the device is
still open.  Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.

Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that.  This fixes the
regession and the original NULL ptr dereference issue.

Fixes: b16939b5 ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch adds FW versions stored in the flash to devlink info_get
callback.  Return the correct fw.psid running version using the
newly added bp->nvm_cfg_ver.

v2:
Ensure stored pkg_name string is NULL terminated when copied to
devlink.

Return directly from the last call to bnxt_dl_info_put().

If the FW call to get stored version fails for any reason, return
success immediately to devlink without the stored versions.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-10-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Add a new function bnxt_dl_info_put() to simplify the code, as there
are more stored firmware version fields to be added in the next patch.

Also, rename fw_ver variable name to ncsi_ver for better naming while
copying to devlink info_get cb.

v2:
Ensure active_pkg_name string is NULL terminated when copied to
devlink.

Return directly from the last call to bnxt_dl_info_put().
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-9-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Add a new bnxt_hwrm_nvm_get_dev_info() to query firmware version
information via NVM_GET_DEV_INFO firmware command.  Use it to
get the running version of the NVM configuration information.

This new function will also be used in subsequent patches to get the
stored firmware versions.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-8-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down.  The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN.  Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Log these values that contain useful firmware state information.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-6-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

event_data1 and event_data2 are used when processing most events.
Store these in local variables at the beginning of the function to
simplify many of the case statements.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-5-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Currently, bp->msg_enable has default value of 0.  It is more useful
to have the commonly used NETIF_MSG_DRV and NETIF_MSG_HW enabled by
default.

v2: Change the fall back bnxt_reset_task() inside bnxt_rx_ring_reset()
to silent mode.  With older fw, we would take the fall back path and
it would be very noisy.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-4-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Online self tests are not disruptive and can be run in NPAR mode
and in multi-host NIC as well.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-3-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

If NVRAM resources are locked, NVM writes are not permitted. In such
scenarios, firmware returns HWRM_ERR_CODE_RESOURCE_LOCKED error to
firmware commands.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-2-git-send-email-michael.chan@broadcom.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Currently, the driver will schedule RX ring reset when we get a buffer
error in the RX completion record.  These RX buffer errors can be due
to normal out-of-buffer conditions or a permanent error in the RX
ring.  Because the driver cannot distinguish between these 2
conditions, we assume all these buffer errors require reset.

This is very disruptive when it is just a normal out-of-buffer
condition.  Newer firmware will now monitor the rings for the permanent
failure and will send a notification to the driver when it happens.
This allows the driver to reset only when such a notification is
received.  In environments where we have predominently out-of-buffer
conditions, we now can avoid these unnecessary resets.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is logic in the RX path to detect unexpected handles in the
RX completion.  We'll print a warning and schedule a reset.  The
next expected handle is then set to 0xffff which is guaranteed to
not match any valid handle.  This will force all remaining packets in
the ring to be discarded before the reset.  There can be hundreds of
these packets remaining in the ring and there is no need to print the
warnings for these forced errors.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a per ring rx_resets counter to count these RX resets.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some older chips, it is necessary to do a reset when we get buffer
errors associated with an RX ring.  These buffer errors may become
frequent if the RX ring underruns under heavy traffic.  The current
code does a global reset of all reasources when this happens.  This
works but creates a big disruption of all rings when one RX ring is
having problem.  This patch implements a localized RX ring reset of
just the RX ring having the issue.  All other rings including all
TX rings will not be affected by this single RX ring reset.

Only the older chips prior to the P5 class supports this reset.
Because it is not a global reset, packets may still be arriving
while we are calling firmware to reset that ring.  We need to be
sure that we don't post any buffers during this time while the
ring is undergoing reset.  After firmware completes successfully,
the ring will be in the reset state with no buffers and we can start
filling it with new buffers and posting them.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_init_one_rx_ring() includes logic to initialize the BDs for one RX
ring and to allocate the buffers.  Separate the allocation logic into a
new bnxt_alloc_one_rx_ring() function.  The allocation function will be
used later to allocate new buffers for one specified RX ring when we
reset that RX ring.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_free_rx_skbs() frees all the allocated buffers and SKBs for
every RX ring.  Refactor this function by calling a new function
bnxt_free_one_rx_ring_skbs() to free these buffers on one specified
RX ring at a time.  This is preparation work for resetting one RX
ring during run-time.
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If firmware does not come out of reset, log FW health status info
to provide more information on firmware status.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NS3 SoC platforms require assistance from the OP-TEE to recover
firmware if a crash occurs while no driver is bound. The
CRASHED_NO_MASTER condition is recorded in the firmware status register
during the crash to indicate when driver intervension is needed to
coordinate a firmware reload. This condition is detected during early
driver initialization in order to effect a firmware fastboot on
supported platforms when necessary.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware now supports device independent discovery of the status
register location. This status register can provide more detailed
information about firmware errors, especially if problems occur
before the HWRM interface is functioning. Attempt to map this
register if it is present and report the firmware status on firmware
init failures.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The allocator for the firmware health structure conflates allocation
and capability checks, limiting the reusability of the code. This patch
separates out the capability check and disablement and improves the
warning message to better describe the consequences of an allocation
failure.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Main changes is to extend hwrm_nvm_get_dev_info_output() for stored
firmware versions and a new flag is added to fw_status_reg.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace /* no break */ comments with the new pseudo-keyword macro
fallthrough[1].

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current logic that calculates the preset maximum value for combined
channel does not take into account the rings used for XDP and mqprio
TCs.  Each of these features will reduce the number of TX rings.  Add
the logic to divide the TX rings accordingly based on whether the
device is currently in XDP mode and whether TCs are in use.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This feature allows the user to set the different FEC modes on the NIC
port.  Any new setting will take effect immediately after a link toggle.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement .get_fecparam() method to report the configured and active FEC
settings.  Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port.  Firmware
will send notification to the driver for the disabled port when this
happens.  Define a new field in the link_info structure to keep track
of this state.  The new phy_state field replaces the unused loop_back
field.

Log a message when the phy_state changes state.  In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool PAM4 link modes for:
        50000baseCR_Full
        100000baseCR2_Full
        200000baseCR4_Full
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware interface has added support for new link speeds using
PAM4 modulation.  Expand the bnxt_link_info structure to closely
mirror the new firmware structures.  Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.

Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.

The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips.  Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.

Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.

Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.

As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>