Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile.
Remove IIO_TRIGGER if present since IIO_BUFFER selects it.
Signed-off-by: NAlison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This just adds support for reporting illuminance with default settings.

Important default registers are written on probe because the device
otherwise lacks a reset function.
Signed-off-by: NCrestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

ultraviolet (UV) light sensor with I2C interface with a peak
sensitivity at 355 nm

strangely, chip uses two addresses 0x38 and 0x39 for LSB and
MSB data, resp.

datasheet: http://www.vishay.com/docs/84277/veml6070.pdfSigned-off-by: NPeter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This is a reimplementation of the old misc device driver for the
ROHM BH1780 ambient light sensor (drivers/misc/bh1780gli.c).

Differences from the old driver:
- Uses the IIO framework
- Uses runtime PM to idle the hardware after 5 seconds
- No weird custom power management from userspace
- No homebrewn values in sysfs

This uses the same (undocumented) device tree compatible-string
as the old driver ("rohm,bh1780gli").

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add support for UPISEMI us5182d als and proximity sensor.
Supports raw readings.
Data sheet for this device can be found here:
http://www.upi-semi.com/temp/uS5182D-DS-P0103-temp.pdfSigned-off-by: NAdriana Reus <adriana.reus@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

APDS9960 is a combination of ALS, proximity, and gesture sensors.

This patch adds support for these functions along with gain control,
integration time, and event thresholds.
Signed-off-by: NMatt Ranostay <mranostay@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add support for TXC PA12203001 als and proximity sensor.
Support for raw illuminance and proximity readings.
Signed-off-by: NAdriana Reus <adriana.reus@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

TI's opt3001 light sensor is a simple and yet powerful
little device. The device provides 99% IR rejection,
automatic full-scale, very low power consumption and
measurements from 0.01 to 83k lux.

This patch adds support for that device using the IIO
framework.

See http://www.ti.com/product/opt3001 for more information.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAndreas Dannenberg <dannenberg@ti.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The use of regmap in commit 2f2c9633 requires REGMAP_I2C to be selected, in
order to meet all dependencies.

Fixes: 2f2c9633 ("iio: ltr501: Add regmap support.")
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Acked-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The stk3310 driver makes use of regmap_i2c, so this dependency needs to be
reflected in Kconfig.
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The use of regmap in commit 2f2c9633 requires REGMAP_I2C to be selected, in
order to meet all dependencies.

Fixes: 2f2c9633 ("iio: ltr501: Add regmap support.")
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Acked-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

The stk3310 driver makes use of regmap_i2c, so this dependency needs to be
reflected in Kconfig.
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds support for ROHM RPR0521 ambient light and proximity
sensor. It offers raw readings for intensity and proximity.
Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Fix the typo in the module description for the CM3323.
Signed-off-by: NHartmut Knaack <knaack.h@gmx.de>
Reviewed-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver adds the initial support for the ACPI Ambient Light Sensor
as defined in Section 9.2 of the ACPI specification (Revision 5.0) [1].

Sensors complying with the standard are exposed as ACPI devices with
ACPI0008 as hardware ID and provide standard methods by which the OS
can query properties of the ambient light environment the system is
currently operating in.

This driver currently allows only to get the current ambient light
illuminance reading through the _ALI method, but is ready to be
extended extended to handle _ALC, _ALT and _ALP as well.

[1] http://www.acpi.info/DOWNLOADS/ACPIspec50.pdfSigned-off-by: NMartin Liska <marxin.liska@gmail.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add support for ROHM BH1710/BH1715/BH1721/BH1750/BH1751 ambient light
sensors.
Signed-off-by: NTomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Minimal implementation of an IIO driver for the Sensortek
STK3310 ambient light and proximity sensor. The STK3311
model is also supported.

Includes:
- ACPI support;
- read_raw and write_raw;
- reading and setting configuration parameters for gain/scale
  and integration time for both ALS and PS.
- power management
Signed-off-by: NTiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Added support for Liteon 301 Ambient light sensor. Since
LTR-301 and LTR-501 are register compatible(and even have same
part id), LTR-501 driver has been extended to support both
devices. LTR-501 is similar to LTR-301 in ALS sensing, But the
only difference is, LTR-501 also supports proximity sensing.

LTR-501 - ALS + Proximity combo
LTR-301 - ALS sensor.
Signed-off-by: NKuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This device is register compatible with LTR501, with a minor difference for
ALS control register as showed below:

ALS Control register for LTR501:

    7      6      5      4      3      2      1      0
+------+------+------+------+------+------+------+------+
|                           |      |      |             |
|        Reserved           | Gain |  SW  |    ALS Mode |
|                           |      | Reset|             |
+------+------+------+------+------+------+------+------+

ALS Control register for LTR559:

    7      6      5      4      3      2      1      0
+------+------+------+------+------+------+------+------+
|                    |                    |      |      |
|     Reserved       |        Gain        |  SW  | ALS  |
|                    |                    | Reset| Mode |
+------+------+------+------+------+------+------+------+

We handle this difference by introducing ltr501_chip_info.

Datasheet for LTR559 is at:
http://optoelectronics.liteon.com/upload/download/DS86-2013-0003/S_110_LTR-559ALS-01_DS_V1.pdfSigned-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Minimal implementation providing raw light intensity
and integration time attribute.

Userspace applications can use GREEN channel for raw
illuminance readings following this table:

Integration Time | G Sensitivity
================================
40 ms            | 0.18
80 ms            | 0.09
160 ms           | 0.045
320 ms           | 0.0225
640 ms           | 0.01125
1280 ms          | 0.005625
Signed-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds missing 'select' statement for gp2ap020a00f driver.
Without regmap_i2c, we get the following error when loading the module:
Unknown symbol devm_regmap_init_i2c.
Signed-off-by: NRoberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds missing 'select' statement for jsa1212 driver.
Without regmap_i2c, we get the following error when loading the module:
Unknown symbol devm_regmap_init_i2c.
Signed-off-by: NRoberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: NDaniel Baluta <daniel.baluta@intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

CM3232 is an advanced ambient light sensor with I2C protocol interface.
The I2C slave address is internally hardwired as 0x10 (7-bit).  Writing
to configure register is byte mode, but reading ALS register requests to
use word mode for 16-bit resolution.
Signed-off-by: NKevin Tsai <ktsai@capellamicro.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch fixes the following checkpatch.pl warning:
WARNING: please write a paragraph that describes the config symbol fully
Signed-off-by: NRoberta Dobrescu <roberta.dobrescu@gmail.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds a new driver for solteam opto JSA1212 proximity and
ambient light sensor.

Basic details of the chip can be found here.

http://www.solteamopto.com.tw/detail.php?ms=3&po_unit=2&pt_unit=29&p_unit=120Signed-off-by: NKuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Minimal implementation. This driver provides raw illuminance readings.

This is based on drivers/hwmon/al3320.c (*) driver from msm tree written
by Tsechih Lin <Tsechih_Lin@asus.com>

* https://android.googlesource.com/kernel/msm.gitSigned-off-by: NDaniel Baluta <daniel.baluta@intel.com>
Reviewed-by: NHartmut Knaack <knaack.h@gmx.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

16-bit digital color sensor with red, green, blue and clear channel

datasheet: http://ams.com/eng/content/download/250258/975997/TCS3414_Datasheet_EN_v1.pdfSigned-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

datasheet: http://www.intersil.com/content/dam/Intersil/documents/isl2/isl29125.pdfSigned-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Added usage id processing for Proximity (Human Presence).
This uses IIO interfaces for triggered buffer to present data
to user mode. This uses HID sensor framework for registering
callback events from the sensor hub.
Signed-off-by: NArchana Patni <archana.patni@intel.com>
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

combined ambient light (two channels) and proximity sensor with I2C
interface; the ALS channels are visible+IR and IR

datasheet is here
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/P_100_LTR-501ALS-01_PrelimDS_ver1.1.pdf

v3:
* fix use of sizeof in _read_als()
v2: (thanks to Lars-Peter Clausen)
* cannot use devm_iio_device_register() due to cleanup order in _remove()
* mutex around data wait/read
* turn info message in _probe() into check for part number
* change copyright year to 2014
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: NKevin Tsai <ktsai@capellamicro.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

drivers/built-in.o: In function `gp2ap020a00f_thresh_event_handler':
powercap_sys.c:(.text+0x15f90c): undefined reference to `irq_work_queue'
make[1]: *** [vmlinux] Error 1
make[1]: Target `uImage' not remade because of errors.
make: *** [sub-make] Error 2
make: Target `uImage' not remade because of errors.

You need the IRQ work support, but GP2AP020A00F is not selecting this
symbol.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds a new driver for Capella CM36651 proximity and RGB sensor.
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Add a new driver for the ambient light/proximity sensor
device. The driver exposes three channels: light_clear
light_ir and proximity. It also supports triggered buffer,
high and low ambient light threshold event and proximity
detection events.
Signed-off-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

chip has four 16-bit channels for red, green, blue, clear color
intensity; driver supports the TCS3x7x family of devices and was
tested with a TCS34725 chip; further information here:
http://www.ams.com/eng/Products/Light-Sensors/Color-Sensor/TCS34725

v2 (thanks to Jonathan Cameron):
* drop dynamic buffer allocation, buffer is in tcs3472_data
* limit sysfs output to PAGE_SIZE
* check val2 == 0 when writing CALIBSCALE
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Cc: Jon Brenner <jon.brenner@ams.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

driver for the TSL4531 family of 16-bit I2C ambient light
sensors; information is here:
http://www.ams.com/eng/Products/Light-Sensors/Ambient-Light-Sensor-ALS/TSL45315

the chip offers simple lux output

v3 (thanks Lars-Peter Clausen):
* add mutex to when updating integration time
* fix chip ID checking
* code cleanups
v2:
* rename to tsl4351
* use INT_TIME
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This patch adds IIO driver for APDS9300 ambient light sensor (ALS).
http://www.avagotech.com/docs/AV02-1077EN

The driver allows to read raw data from ADC registers or calculate
lux value. It also can handle threshold interrupt.
Signed-off-by: NOleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.

Also reorder those  entries which weren't in alphabetical order yet.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

This driver is simple, uses the latest interfaces and contains few if
any controversial elements.  All of its interfaces have been in place
for a long time now.  Hence let's move it out of staging.
Signed-off-by: NJonathan Cameron <jic23@kernel.org>
Acked-by: NPeter Meerwald <pmeerw@pmeerw.net>