Previously, we used the swq_id's mechanism
to have AC and HW queue different only for
aggregation queues. To be able to fix a bug
with iPAN simply always build the swq_id as
ac | (hwq << 2) and remove the flag bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Instead of passing the txq->swq_id, pass the
txq struct directly to make sure that in the
future nobody will pass an invalid number.
Only three places actually change from using
the txq_id or the skb's queue_mapping to now
using txq->swq_id as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Even if this check were to happen, using the
txq_id here (which is a HW queue) would lead
to confusion in mac80211. Luckily, it doesn't
seem like this can ever happen.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Simply remove the unused variable swq_id.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Some variables are misnamed in the FIFO setup
code, fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Set the default led mode for different devices.

For the newer devices such as 6000g2a, 6000g2b and newer,
the default led mode is On/Off instead of blinking.

The led_mode still can be control through module parameter
  0: system default
  1: On/Off
  2: blinking
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Change the default BT_KILL_ACK_MASK and BT_KILL_CTS_MASK for BT coex
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Setting the max/min/def value for BT dynamic aggregation threshold.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For newer devices, uCode provide both "number of frames sent"
and "number of frames acked" information inside the compressed_ba
packet. So instead of figure the success/failure information through
the bitmap, use those information which is much betrer approach.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This patch replaces the handcrafted
sign extension cruft with a generic
bitop function.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Acked-by: NLuciano Coelho <luciano.coelho@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were two type of isr supported by iwlwifi devices.
  legacy isr - only used by legacy devices (3945 & 4965)
  ict isr - used by all new generation of iwlwifi devices

Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 100 series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u.  This meant that you could see
negative numbers instead of a clean wrap.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.

v2: Add extra documentation for register fields
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.

We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'
Signed-off-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>