- 28 3月, 2012 29 次提交
-
-
由 Alexander Stein 提交于
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jaehoon Chung 提交于
Someone could use send_hpi_cmd() on a card that doesn't advertise support for HPI. Then maybe didn't work fine. Because card->ext_csd.hpi_cmd didn't set. So if card didn't support hpi, return the warning message. And CMD12's flags is MMC_RSP_R1B. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ido Yariv 提交于
For small size non-dma sdio transactions, it is sometimes better to poll the mmc host and avoid interrupts altogether. Polling lowers the number of interrupts and context switches. Tests have shown that for small transactions, only a few polling iterations are needed, so this is worth while. Signed-off-by: NIdo Yariv <ido@wizery.com> Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ido Yariv 提交于
The davinci mmc interrupt handler fills the fifo, as long as the DXRDY or DRRDY bits are set in the status register. If interrupts fire during this loop, they will be handled by the handler, but the interrupt controller will still buffer these. As a result, the handler will be called again to serve these needlessly. In order to avoid these spurious interrupts, keep interrupts masked while filling the fifo. Signed-off-by: NIdo Yariv <ido@wizery.com> Tested-by: NRajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
When booting with Device tree, the omap_hsmmc driver does not program the pbias cell (inside OMAP control module) during a regulator voltage change. In case of non-dt boot, this is handled using callbacks from within platform_data and implemented in machine code. To be able to do this with device tree, without invoking any machine code, a OMAP control module driver is needed which is yet missing. The pbias cell is used to provide a 1.8v or 3.0v reference to the mmc/sd/sdio1 interface supporting both 1.8v and 3.0v voltages. Until a OMAP control module driver is available to handle this, when booting with a device tree blob, never change the regulator voltage which might then require a pbias cell re-program. There are 2 instances where in the mmc regulator voltage can be changed. -1- when the regulator is turned OFF. -2- when attempting a switch to 1.8v from 3.0v for dual volt cards This patch avoids a voltage change in both cases when booting from device tree, and hence compromises on power savings. Once the OMAP control module driver is available and hsmmc driver is modified to then do pbias programming even when booting with device tree, these limitaions can be removed to achieve better power savings. Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
Define dt bindings for the ti-omap-hsmmc, and adapt the driver to extract data (which was earlier passed as platform_data) from device tree. Signed-off-by: NRajendra Nayak <rnayak@ti.com> Acked-by: NRob Herring <rob.herring@calxeda.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Adrian Hunter 提交于
SDIO is powered separately from the host controller, so the card can remain on while the host controller is powered off during suspend. Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Adrian Hunter 提交于
Add quirk SDHCI_QUIRK2_HOST_OFF_CARD_ON to cater for the case when the card keeps power during suspend but the host controller does not i.e. the card power is not controlled by the host controller. In that case, the controller must be fully reset on resume. Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Adrian Hunter 提交于
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Adrian Hunter 提交于
Let drivers specify the use of high-capacity erase size. Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
Convert all instances of pr_* prints within the driver to instead use dev_* prints. Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Shimoda, Yoshihiro 提交于
The MMC_GEN_CMD (CMD56) doesn't need to check busy signal. So, the patch fixes the setting. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Subhash Jadavani 提交于
This patch fixes following issues when HS200 is enabled: 1. If executing_tuning() host ops is called without mmc_host_clk_hold(), card clocks might get turned off (if MMC_CLK_GATING is enabled) while execute_tuning() is in progress. So this patch makes sure that execute_tuning() is called with mmc_host_clk_hold(). 2. If host timing mode is set to HS200 mode, there should not be any communication with the card until execute_tuning() is completed. But there is a chance that CMD6 might be sent to enable set HPI_EN (of HPI_MGMT field in EXT_CSD) before execute_tuning() is called. So this patch moves this operation after execute_tuning() is completed. Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org> Reviewed-by: girish.shivananjappa@linaro.org Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Tony Lindgren 提交于
Otherwise we can get following warning when re-loading the omap_hsmmc driver module when gpio_twl4030 module is not loaded: omap_hsmmc omap_hsmmc.0: Unbalanced pm_runtime_enable! omap_hsmmc omap_hsmmc.0: Unable to grab MMC CD IRQ omap_hsmmc: probe of omap_hsmmc.0 failed with error -22 Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ulf Hansson 提交于
Make sure mmc_start_req cancels the prepared job, if the request was prevented to be started due to the card has been removed. This bug was introduced in commit: mmc: allow upper layers to know immediately if card has been removed Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com> Reviewed-by: NPer Forlin <per.forlin@stericsson.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Adrian Hunter 提交于
Most parts of the enable / disable API are no longer used and can be removed. Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Tested-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Shiraz Hashim 提交于
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Guennadi Liakhovetski 提交于
If TMIO MMC is used in polling mode, or the card is non-removable, or card-detection is performed, using an external interrupt, there is no need to enable controller native card hotplug interrupts. Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
MMC1 is not the only instance that can be used/wired for SD. So remove this assumption from the driver. Now that all the mmc id based usage is removed, get rid of all the DEVID defines and also the 'id' field from the omap_hsmmc_host structure. Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Tested-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
Now that omap_hsmmc_set_power() already has a check to return 0 if !host->vcc, it seems like it can be used even on MMC4 instead of the dummy omap_hsmmc_4_set_power(). This also helps get rid of all the host->id based check to populate the right function for on-chip/external level shifting and use omap_hsmmc_set_power() for all MMC modules. Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Tested-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Rajendra Nayak 提交于
Use omap_hsmmc_235_set_poweri() (now renamed as omap_hsmmc_set_power()) for MMC1 instance as well and get rid of omap_hsmmc_1_set_power() completely. omap_hsmmc_235_set_power() seems to be implemented as a superset of omap_hsmmc_1_set_power() with additional functionality implemented based on additional checks and hence should just work for MMC1 as well. Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Tested-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Balaji T K 提交于
Use OMAP_HSMMC_SUPPORTS_DUAL_VOLT flag instead of host->id for identifying SD bus voltage capabilities. Signed-off-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Balaji T K 提交于
set_sleep seems to be unused in omap_hsmmc driver. so get rid of it. Signed-off-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Balaji T K 提交于
Git rid of hardcoded tx/rx DMA channels based on pdev->id and use platform_get_resource_byname() to retrieve them instead. Signed-off-by: NBalaji T K <balajitk@ti.com> Signed-off-by: NRajendra Nayak <rnayak@ti.com> Tested-by: NVenkatraman S <svenkatr@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ulf Hansson 提交于
To prevent I/O as soon as possible at card removal, a new detect work is re-scheduled without a delay to let a rescan remove the card device as soon as possible. Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly" removed cards that a scheduled detect work did not detect as removed. To prevent further I/O requests for these lingering removed cards, check if card has been removed and then schedule a detect work to properly remove it. Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com> Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req") broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if using internal DMA. In case of using other DMA it returns -ENOSYS. It prevents the DMA operations. This patch makes dw_mci_pre_dma_transfer() effective in all DMA cases again. Reported-by: NJames Hogan <james@albanarts.com> Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com> Acked-by: NJames Hogan <james.hogan@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jaehoon Chung 提交于
When disable CONFIG_MMC_DW_IDMAC, can see the compiler error. Because in dw_mci_post_req(), called the dw_mci_get_dma_dir(). But that function is in #ifdef CONFIG_MMC_DW_IDMAC. I think that function is generic function. Not need the CONFIG_MMC_DW_IDMAC. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NSeungwon Jeon <tgih.jun@samsung.com> Acked-by: NJames Hogan <james.hogan@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Daniel Mack 提交于
External circuitry like level shifters may limit the maximum operation speed of the hsmmc controller. Add a field to struct omap2_hsmmc_info so boards can adjust the setting on demand. Signed-off-by: NDaniel Mack <zonque@gmail.com> Acked-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Ludovic Desroches 提交于
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
- 26 3月, 2012 11 次提交
-
-
由 Jaehoon Chung 提交于
In CLKENA register, can support 16-SD card clocks. If support correctly, must shift with slot-id. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NWill Newton <will.newton@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jerry Huang 提交于
SD card read was failing (data crc error) on some cards at maximum possible frequency on P1010 (CCB frequency set to 400MHz). Some clock deviations are also observed at this frequency. Hence reduced the mmc clock freq. Signed-off-by: NPriyanka Jain <Priyanka.Jain@freescale.com> Singed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com> Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jaehoon Chung 提交于
This patch is added just debug message. Almost features need to use the CMD23. But we didn't see the debug message for sbc. If sbc's message can see, should be help for debugging. (We can check whether use the cmd23 or not.) Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Seungwon Jeon 提交于
This patch implements pre_req and post_req in dw_mmc to support asynchronous mmc request. Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NWill Newton <will.newton@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Stephen Warren 提交于
Tegra30 differs from Tegra20 in a number of ways. This patch implements a minimal set of differences in order to get the Cardhu board's SD slot and eMMC working. Given the diffs between the mainline sdhci-tegra.c and our downstream versions, I expect we'll eventually need to add many more differences, hence the seemingly heavy-weight addition of the soc_data structure. * Tegra30 doesn't need to override register access to SDHCI_HOST_VERSION or SDHCI_INT_ENABLE. * Tegra30 needs quirk SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jerry Huang 提交于
For FSL ESDHC controllers, when entering sleep the controller will power off, therefore the registers will lose their values, and the driver should save the value of registers during suspend and write them back during resume. Signed-off-by: NJerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: NJiang Yutang <b14898@freescale.com> Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Chris Ball 提交于
Some platforms require saving/restoring registers across suspend/resume; this hook allows them to do that inside their driver. Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jaehoon Chung 提交于
When use the IDMAC, we can also want to use the pdata->blk-setting. So if pdata->blk-setting is unset, use the default value. if not, use the pdata->blk-setting. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NWill Newton <will.newton@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Shashidhar Hiremath 提交于
Support of PCI mode for the dw_mmc driver. This Patch adds the support for the scenario where the Synopsys Designware IP is present on the PCI bus. The patch adds the minimal modifications necessary for the driver to work on PCI platform. Also added separate files for PCI and PLATFORM modes of operation. Signed-off-by: NShashidhar Hiremath <shashidharh@vayavyalabs.com> Acked-by: NJames Hogan <james.hogan@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Jaehoon Chung 提交于
This patch adds the capability of power off notify for dw-mmc controller. In order to use Girish's patch: mmc: core: Add Power Off Notify Feature eMMC 4.5 Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NWill Newton <will.newton@imgtec.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-
由 Saugata Das 提交于
MMC-4.5 data tag feature will be used to store the file system meta-data in the tagged region of eMMC. This will improve the write and subsequent read transfer time for the meta data. Signed-off-by: NSaugata Das <saugata.das@linaro.org> Tested-by: NVenkatraman S <svenkatr@ti.com> Signed-off-by: NChris Ball <cjb@laptop.org>
-