Commit 597c56e3 ("xhci: update bounce buffer with correct sg num")
caused the following build warnings:

drivers/usb/host/xhci-ring.c:676:19: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t {aka unsigned int}' [-Wformat=]

Use %zu for printing size_t type in order to fix the warnings.

Fixes: 597c56e3 ("xhci: update bounce buffer with correct sg num")
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Xhci_handshake() implements the algorithm already captured by
readl_poll_timeout_atomic(). Convert the former to use the latter to
avoid repetition.

Turned out this patch also fixes a bug on the AMD Stoneyridge platform
where usleep(1) sometimes takes over 10ms.
This means a 5 second timeout can easily take over 15 seconds which will
trigger the watchdog and reboot the system.

[Add info about patch fixing a bug to commit message -Mathias]
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: NRaul E Rangel <rrangel@chromium.org>
Reviewed-by: NRaul E Rangel <rrangel@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci immediate data transfer (IDT) support in 5.2-rc1 caused regression
on various Samsung Exynos boards with ASIX USB 2.0 ethernet dongle.

If the transfer buffer in the URB is already DMA mapped then IDT should
not be used. urb->transfer_dma will already contain a valid dma address,
and there is no guarantee the data in urb->transfer_buffer is valid.

The IDT support patch used urb->transfer_dma as a temporary storage,
copying data from urb->transfer_buffer into it.

Issue was solved by preventing IDT if transfer buffer is already dma
mapped, and by not using urb->transfer_dma as temporary storage.

Fixes: 33e39350 ("usb: xhci: add Immediate Data Transfer support")
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
CC: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With defective USB sticks we see the following error happen:
usb 1-3: new high-speed USB device number 6 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: device descriptor read/64, error -71
usb 1-3: new high-speed USB device number 7 using xhci_hcd
usb 1-3: device descriptor read/64, error -71
usb 1-3: unable to get BOS descriptor set
usb 1-3: New USB device found, idVendor=0781, idProduct=5581
usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008

This comes from the following place:
[ 1660.215380] IP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.222092] PGD 0 P4D 0
[ 1660.224918] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 1660.425520] CPU: 1 PID: 38 Comm: kworker/1:1 Tainted: P     U  W  O    4.14.67-apl #1
[ 1660.434277] Workqueue: usb_hub_wq hub_event [usbcore]
[ 1660.439918] task: ffffa295b6ae4c80 task.stack: ffffad4580150000
[ 1660.446532] RIP: 0010:xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd]
[ 1660.453821] RSP: 0018:ffffad4580153c70 EFLAGS: 00010046
[ 1660.459655] RAX: 0000000000000000 RBX: ffffa295b4d7c000 RCX: 0000000000000002
[ 1660.467625] RDX: 0000000000000002 RSI: ffffffff984a55b2 RDI: ffffffff984a55b2
[ 1660.475586] RBP: ffffad4580153cc8 R08: 0000000000d6520a R09: 0000000000000001
[ 1660.483556] R10: ffffad4580a004a0 R11: 0000000000000286 R12: ffffa295b4d7c000
[ 1660.491525] R13: 0000000000010648 R14: ffffa295a84e1800 R15: 0000000000000000
[ 1660.499494] FS:  0000000000000000(0000) GS:ffffa295bfc80000(0000) knlGS:0000000000000000
[ 1660.508530] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1660.514947] CR2: 0000000000000008 CR3: 000000025a114000 CR4: 00000000003406a0
[ 1660.522917] Call Trace:
[ 1660.525657]  usb_set_usb2_hardware_lpm+0x3d/0x70 [usbcore]
[ 1660.531792]  usb_disable_device+0x242/0x260 [usbcore]
[ 1660.537439]  usb_disconnect+0xc1/0x2b0 [usbcore]
[ 1660.542600]  hub_event+0x596/0x18f0 [usbcore]
[ 1660.547467]  ? trace_preempt_on+0xdf/0x100
[ 1660.552040]  ? process_one_work+0x1c1/0x410
[ 1660.556708]  process_one_work+0x1d2/0x410
[ 1660.561184]  ? preempt_count_add.part.3+0x21/0x60
[ 1660.566436]  worker_thread+0x2d/0x3f0
[ 1660.570522]  kthread+0x122/0x140
[ 1660.574123]  ? process_one_work+0x410/0x410
[ 1660.578792]  ? kthread_create_on_node+0x60/0x60
[ 1660.583849]  ret_from_fork+0x3a/0x50
[ 1660.587839] Code: 00 49 89 c3 49 8b 84 24 50 16 00 00 8d 4a ff 48 8d 04 c8 48 89 ca 4c 8b 10 45 8b 6a 04 48 8b 00 48 89 45 c0 49 8b 86 80 03 00 00 <48> 8b 40 08 8b 40 03 0f 1f 44 00 00 45 85 ff 0f 84 81 01 00 00
[ 1660.608980] RIP: xhci_set_usb2_hardware_lpm+0xdf/0x3d0 [xhci_hcd] RSP: ffffad4580153c70
[ 1660.617921] CR2: 0000000000000008

Tracking this down shows that udev->bos is NULL in the following code:
(xhci.c, in xhci_set_usb2_hardware_lpm)
	field = le32_to_cpu(udev->bos->ext_cap->bmAttributes);  <<<<<<< here

	xhci_dbg(xhci, "%s port %d USB2 hardware LPM\n",
			enable ? "enable" : "disable", port_num + 1);

	if (enable) {
		/* Host supports BESL timeout instead of HIRD */
		if (udev->usb2_hw_lpm_besl_capable) {
			/* if device doesn't have a preferred BESL value use a
			 * default one which works with mixed HIRD and BESL
			 * systems. See XHCI_DEFAULT_BESL definition in xhci.h
			 */
			if ((field & USB_BESL_SUPPORT) &&
			    (field & USB_BESL_BASELINE_VALID))
				hird = USB_GET_BESL_BASELINE(field);
			else
				hird = udev->l1_params.besl;

The failing case is when disabling LPM. So it is sufficient to avoid
access to udev->bos by moving the instruction into the "enable" clause.

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NCarsten Schmid <carsten_schmid@mentor.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In xhci_debugfs_create_slot(), kzalloc() can fail and
dev->debugfs_private will be NULL.
In xhci_debugfs_create_endpoint(), dev->debugfs_private is used without
any null-pointer check, and can cause a null pointer dereference.

To fix this bug, a null-pointer check is added in
xhci_debugfs_create_endpoint().

This bug is found by a runtime fuzzing tool named FIZZER written by us.

[subjet line change change, add potential -Mathais]
Signed-off-by: NJia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This change fixes a data corruption issue occurred on USB hard disk for
the case that bounce buffer is used during transferring data.

While updating data between sg list and bounce buffer, current
implementation passes mapped sg number (urb->num_mapped_sgs) to
sg_pcopy_from_buffer() and sg_pcopy_to_buffer(). This causes data
not get copied if target buffer is located in the elements after
mapped sg elements. This change passes sg number for full list to
fix issue.

Besides, for copying data from bounce buffer, calling dma_unmap_single()
on the bounce buffer before copying data to sg list can avoid cache issue.

Fixes: f9c589e1 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: NHenry Lin <henryl@nvidia.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The configure endpoint command configures all the endpoints that were
flagged to be added or dropped.

To know the content of each of the added endpoints we need to add tracing
to the .add_endpoint() callback, just after initializing all the context
values.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add tracing for the add and drop bits in the input control context
used in Address device, configure endpoint, evaluate context commands.

The add and drop bits tell xHC which enpoints are added and dropped.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Improve port related dynamic debugging by printing out the bus number,
port number and port status register content each time there is a port
related debug messages.

Use the same port numbering method as usbcore to simplify debugging.
i.e. starting with port number 1.
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Immediate data transfers (IDT) allow the HCD to copy small chunks of
data (up to 8bytes) directly into its output transfer TRBs. This avoids
the somewhat expensive DMA mappings that are performed by default on
most URBs submissions.

In the case an URB was suitable for IDT. The data is directly copied
into the "Data Buffer Pointer" region of the TRB and the IDT flag is
set. Instead of triggering memory accesses the HC will use the data
directly.

The implementation could cover all kind of output endpoints. Yet
Isochronous endpoints are bypassed as I was unable to find one that
matched IDT's constraints. As we try to bypass the default DMA mappings
on URB buffers we'd need to find a Isochronous device with an
urb->transfer_buffer_length <= 8 bytes.

The implementation takes into account that the 8 byte buffers provided
by the URB will never cross a 64KB boundary.
Signed-off-by: NNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.

Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so the
replacement doesn't change original purpose.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

fhci_queue_urb() shouldn't use urb->pipe to compute the maxpacket
size anyway.It should use usb_endpoint_maxp(&urb->ep->desc).
Signed-off-by: NYan Zhu <zhuyan34@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.
Signed-off-by: NJC Kuo <jckuo@nvidia.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Starting with Tegra186, the XUSB controller no longer has the IPFS
wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc
that can be used to declare the existence of the IPFS wrapper.

For the existing chips (i.e. Tegra124 and Tegra210), the new field is
set to true. A future patch adding support for Tegra186 will set it to
false.
Signed-off-by: NJC Kuo <jckuo@nvidia.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All users now setup a fixed regulator for the vbus supply. We can drop
the vbus GPIO code.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Historically the power supply management in this driver has been handled
in two separate places in parallel. Device-tree users simply defined an
appropriate regulator, while two boards with no DT support (da830-evm and
omapl138-hawk) passed functions defined in their respective board files
over platform data. These functions simply used legacy GPIO calls to
watch the oc GPIO for interrupts and disable the vbus GPIO when the irq
fires.

Commit d193abf1 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
updated these GPIO calls to the modern API and moved them inside the
driver.

This however is not the optimal solution for the vbus GPIO which should
be modeled as a fixed regulator that can be controlled with a GPIO.

In order to keep the overcurrent protection available once we move the
board files to using fixed regulators we need to disable the enable_reg
regulator when the overcurrent indicator interrupt fires. Since we
cannot call regulator_disable() from interrupt context, we need to
switch to using a oneshot threaded interrupt.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

There's no reason to have a separate variable to keep track of the
regulator state. The regulator core already does that. Remove
reg_enabled from struct da8xx_ohci_hcd.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>

if platform_driver_register fails, cleanup the allocated resource
gracefully.
Signed-off-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case create_singlethread_workqueue fails, the fix notifies
callers the error to avoid potential NULL pointer dereferences.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled

move the memory cleanup outside the spinlock

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.

Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.

Add U1 and U2 to the possible link states when checking for finished
port resume.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.

[  101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?

Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
Signed-off-by: NYasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: NSpyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: NBalaji Manoharan <m.balaji@intel.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.

This function is only used in xhci-mem.c so just make it static.
Signed-off-by: NJean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replaced "xhci_dbc_flush_reqests" with xhci_dbc_flush_requests".
Signed-off-by: NPrabhat Chand Pandey <prabhat.chand.pandey@intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The member @parent of xhci_regset struct is not used in fact,
so remove it
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Fixes: 6494a9ad ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
 variable 'uframes' set but not used [-Wunused-but-set-variable]

drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
 variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]

They are never used since introduction.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A statement is indented too deeply, fix this by removing a tab.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are two users upstream which register external callbacks for
switching the port power on/off and overcurrent protection. Both
users only use two GPIOs for that. Instead of having that functionality
in the board files, move the logic into the OHCI driver - including
the interrupt handler for overcurrent detection.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add a helper pointer to &pdev->dev. This improves readability by
removing all the &pdev->dev dereferencing.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add a new line after local variables. This improves the coding style.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add suspend/resume callbacks to reset the host controller properly
during S2RAM operation.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to initialize the PHY from the driver's probe. It is done by
the core automatically and doing it twice would increment the
phy->powercount counter to 2 instead of 1. During later suspend
operation, the counter will be decremented to one, no phy->power_off()
will occur and worse than that, the following phy->power_on() at
resume time will also be skipped, failing the whole S2RAM operation.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The mvebu xHCI host driver does not have suspend/resume support. Use of
the XHCI_RESET_ON_RESUME quirk is mandatory in order to avoid failures
after resume. This will work only if no USB device is plugged-in.

While at it, mention in the Kconfig file that this IP is also present
on the A3700 SoC.
Signed-off-by: NOfer Heifetz <oferh@marvell.com>
[miquel.raynal@bootlin.com: Reword the commit message]
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NGregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We have been using Makefile for well over a decade now, use that name
instead of Kbuild.

Also, while moving the file, add the proper SPDX identifier at the top
of it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>