Incoming hardware will support VHT MU-MIMO. Declare this
capability for relevant hardware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The MAC address parameters passed to iwl_parse_nvm_data() are passed on
to iwl_set_hw_address_family_8000() which treats them as little endian.
Annotate them as such, and add the missing byte-swapping in mvm.

While at it, add the MAC address to the error to make debugging issues
with it easier.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

802.11ac allows A-MSDU that can be up to 12KB long. Since
an entire A-MSDU needs to fit into one single Receive
Buffer (RB), add support for big RBs.
Since this adds lots of pressure to the memory manager and
significantly increase the true_size of the RX buffers,
don't enable this by default.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and on MIMO disabled bit which is
correct in the OTP and set to disabled. This fixes the previous
workaround "force 1x1 antenna in Series 8000".
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is a workaround to an OTP bug. In Series 8000 1x1, the OTP
0xA052 defines 2x2 antenna configuration. This workaround overrides
the decision based on HW id and MIMO disabled bit which is correct
in the OTP and set to disabled.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.

CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The radio cfg DWORD was taken from the wrong place in the
8000 HW family, after a line in the code was wrongly changed
by mistake. This broke several 8260 devices.

Fixes: 5dd9c68a ("iwlwifi: drop support for early versions of 8000")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Take the MAC address from the OTP even if one is present in
the NVM, if that MAC address happens to be a reserved one.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are devices that forbid MIMO by the mean of the NVM.
Detect thoses devices and forbid MIMO otherwise the firmware
would crash. STBC is still allowed on these devices.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.

Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These early versions are no longer supported.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New NVM versions in LnP platforms have the lar_enable bits in a different
offset.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

11ac depends on 11n, so disable it if 11n is disabled.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If LAR is supported in TLV, but the NVM does not enable it, then disable
LAR support and ignore the TLV's bit that enabled LAR.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

max_eirp affects the txpower configured to the power,
so use the max tx power (22) instead of some other
value.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the last 5ghz channel to 165 instead of 161
Add support for 8000 family, until channel 181.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise the regulatory data will mistakenly contain only 7000 series
channels.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove a useless debug print about unsupported channels.
Also add a comment about the LAR special case where channels
might become valid later.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to updated regulatory guidelines, the ACTIVE bit in the NVM
also allows ibss activity on the channel. The IBSS NVM bit is not updated
when LAR is active and is deprecated. Using this bit for NO-IR incorrectly
causes all 5Ghz channels to be marked as passive.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Register to cfg80211 with all channels enabled when LAR is supported.
Appropriate channels will later be disabled when a specific regulatory
domain is defined.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Parse the NVM channel data and create a regulatory domain with a rule
for every 20Mhz channel. Use the AUTO_BW flag so the regulatory core
can unify single-channel rules into ranges.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add two new parameters to iwl_cfg:
max_ht_ampdu_exponent and max_vht_ampdu_exponent.
These parameters, if set, will set new values to the maximum of
HT and VHT A-MPDU exponent for the A-MPDU length exponent.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use LDPC for Tx and publish support for Rx in case the chip
supports LDPC. Enable it for the 7265 family.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The chip is able to transmit up to 22dBm, so set
the constant appropriately.

CC: <stable@vger.kernel.org> [3.13+]
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In family 8000 products the MAC address in the OTP could be in either:
- WFPM address
- PCIE address
In sdio product we should read it from the WFPM, in pcie product we
should read it from the PCIe location.
This is relevant only from otp version 0xE08 and above.
While at it, fix the bytes order in version 0xE08.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Don't use nvm_hw pointer if it is NULL. Print an error
message if the MAC address isn't valid.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

in family 8000: additional channel 14 added to the low
band list. now the number of channels in the low band
is 15.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For family 8000 products, the driver should take the MAC
address from the mac_override section and only if this
section is empty it should take it from the HW section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Number of channels changed from 40 to 50
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As the antenna dependent fields depend on the firmware file and not
the NVM, use those fields in the VHT capability creation.

Additionally, fix the STBC and antenna pattern consistency fields.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

These values aren't used as the firmware values should be used,
so reading them is pointless and hides potential errors when
somebody uses these values. Leave them zero to make it clearer
that they can't be used. We can't remove the struct members as
the DVM driver does read the values from EEPROM/OTP and the
structure is shared between drivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>