iwlwifi: fix NVM channel attribute map.

Fix NVM channel attributes. Add indoor-only and GO Concurrent
bits. Remove DFS channel bit which is overlapped with radar.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

drivers/net/wireless/iwlwifi/iwl-nvm-parse.c

@@ -174,7 +174,9 @@ static struct ieee80211_rate iwl_cfg80211_rates[] = {
  * @NVM_CHANNEL_IBSS: usable as an IBSS channel
  * @NVM_CHANNEL_ACTIVE: active scanning allowed
  * @NVM_CHANNEL_RADAR: radar detection required
- * @NVM_CHANNEL_DFS: dynamic freq selection candidate
+ * @NVM_CHANNEL_INDOOR_ONLY: only indoor use is allowed
+ * @NVM_CHANNEL_GO_CONCURRENT: GO operation is allowed when connected to BSS
+ *	on same channel on 2.4 or same UNII band on 5.2
  * @NVM_CHANNEL_WIDE: 20 MHz channel okay (?)
  * @NVM_CHANNEL_40MHZ: 40 MHz channel okay (?)
  * @NVM_CHANNEL_80MHZ: 80 MHz channel okay (?)
@@ -185,7 +187,8 @@ enum iwl_nvm_channel_flags {
 	NVM_CHANNEL_IBSS = BIT(1),
 	NVM_CHANNEL_ACTIVE = BIT(3),
 	NVM_CHANNEL_RADAR = BIT(4),
-	NVM_CHANNEL_DFS = BIT(7),
+	NVM_CHANNEL_INDOOR_ONLY = BIT(5),
+	NVM_CHANNEL_GO_CONCURRENT = BIT(6),
 	NVM_CHANNEL_WIDE = BIT(8),
 	NVM_CHANNEL_40MHZ = BIT(9),
 	NVM_CHANNEL_80MHZ = BIT(10),
@@ -273,6 +276,16 @@ static int iwl_init_channel_map(struct device *dev, const struct iwl_cfg *cfg,
 		if (ch_flags & NVM_CHANNEL_RADAR)
 			channel->flags |= IEEE80211_CHAN_RADAR;
 
+		if (ch_flags & NVM_CHANNEL_INDOOR_ONLY)
+			channel->flags |= IEEE80211_CHAN_INDOOR_ONLY;
+
+		/* Set the GO concurrent flag only in case that NO_IR is set.
+		 * Otherwise it is meaningless
+		 */
+		if ((ch_flags & NVM_CHANNEL_GO_CONCURRENT) &&
+		    (channel->flags & IEEE80211_CHAN_NO_IR))
+			channel->flags |= IEEE80211_CHAN_GO_CONCURRENT;
+
 		/* Initialize regulatory-based run-time data */
 
 		/*
@@ -282,7 +295,7 @@ static int iwl_init_channel_map(struct device *dev, const struct iwl_cfg *cfg,
 		channel->max_power = DEFAULT_MAX_TX_POWER;
 		is_5ghz = channel->band == IEEE80211_BAND_5GHZ;
 		IWL_DEBUG_EEPROM(dev,
-				 "Ch. %d [%sGHz] %s%s%s%s%s%s(0x%02x %ddBm): Ad-Hoc %ssupported\n",
+				 "Ch. %d [%sGHz] %s%s%s%s%s%s%s(0x%02x %ddBm): Ad-Hoc %ssupported\n",
 				 channel->hw_value,
 				 is_5ghz ? "5.2" : "2.4",
 				 CHECK_AND_PRINT_I(VALID),
@@ -290,7 +303,8 @@ static int iwl_init_channel_map(struct device *dev, const struct iwl_cfg *cfg,
 				 CHECK_AND_PRINT_I(ACTIVE),
 				 CHECK_AND_PRINT_I(RADAR),
 				 CHECK_AND_PRINT_I(WIDE),
-				 CHECK_AND_PRINT_I(DFS),
+				 CHECK_AND_PRINT_I(INDOOR_ONLY),
+				 CHECK_AND_PRINT_I(GO_CONCURRENT),
 				 ch_flags,
 				 channel->max_power,
 				 ((ch_flags & NVM_CHANNEL_IBSS) &&