We can't use msleep() while holding a spinlock, moreower serio's write()
method is supposed to be useable from inettrupt context. Let's do what
i8042 does and poll the status register every 50 us (with udelay).
Reported-by: NMarjan Fojkar <marjan@pajkc.eu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Gigabyte netbook model M1022M requires i8042.noloop, otherwise AUX port
will not detected and the touchpad will not work. Unfortunately chassis
type in DMI set to "Other" and thus generic laptop entry does not fire
on it.
Reported-by: NDarryl Bond <dbond@nrggos.com.au>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Some hardware (such as Dell laptops) signal a variety of events through
the i8042 controller, even if these don't map to keyboard events. Add
support for drivers to filter the i8042 event stream in order to respond
to these events and (if appropriate) block them from entering the input
stream.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We need to protect not only i8042 status and data register from concurrent
access from IRQ 1 and 12 but the rest of the shared state as well, so let's
move release of i8042_lock in i8042_interrupt() a little bit further down.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Relative events are only reported via secondary device therefore device
associated with the touchpad should not advertise these capabilities.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Acked-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Also fix annotation of ps2_test() - it can'be __init since it is called
from __devinit code.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Mark altera_ps2_probe() as __devinit and altera_ps2_remove() as __devexit
so that they can be discarded when not needed.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

del_timer() does not wait for the timer to finish running before returning
and therefore is technically not safe. Also make sure to enable tasklet
before kicking timer that will schedule it.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Setting up owner field ensures that driver core creates symlink from
the driver to a module implementing this driver.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The keymap manipulation code was split into a library module,
so let's make us of it.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

More and more devices choose to reimplement support for sparse keymaps
first introduced by wistron driver. Move it into a library module so it
can be easily used by interested parties.
Reviewed-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Effects were allocated, but not freed anywhere.
Signed-off-by: NJari Vanhala <ext-jari.vanhala@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The driver does not reference identification strings in DMI table and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The driver does not reference identification strings in DMI tables and
since these strings are no longer required by DMI core we can safely
remove them and save some memory.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

DMI tables use considerable amount of memory. Mark them as __initconst
so they will be discarded once module is loaded.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: NAnisse Astier <anisse@astier.eu>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Keyboard handler should not attempt to traverse handler->h_list on
its own, without any locking, otherwise it races with registering
and unregistering of input handles which leads to crashes.

Introduce input_handler_for_each_handle() helper that allows safely
iterate over all handles attached to a particular handler and switch
keyboard handler to use it.
Reported-by: NJim Paradis <jparadis@redhat.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

We need to read and report gpio state when we bind the driver to the
device and upon resume so that userspace has correct state of the
switches (and keys but they are less important since, even if they
are happened to be pressed, we'd expect them to be released fairly
soon).
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

This patch adds support for the ET&T TC5UH 5-wire USB touchscreen controller.
More info at http://www.etandt.com.tw/board_solution.htmlSigned-off-by: NPetr Štetiar <ynezz@true.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Added two new Xbox 360 devices:
   - HORI Real Arcade Pro.EX
   - Mad Catz SFIV Fightpad
Signed-off-by: NNicolas Léveillé <nicolas@uucidl.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

If the poll interval is set to 0 via new sysfs entry and device is
opened after that, polling is started with interval 0. This causes
huge CPU load. Same happens if the rate was 0 when the device was
closed and then reopened.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

It does not make sense to wait poll_interval before performing first
read after opening the device, schedule the read immediately instead.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

S3C24XX touchscreen driver, originally written by Arnaud Patard and
other contributors. The driver has had substantial testing as well as
a number of tidying up passes done by Ben Dooks, as noted:

- added kernel-doc comments to most of the routines
- removed old code from pre adc framework days
- updated device probe code to use platform id list matching
- cleaned up debug, since printk() now has timestamp feature
- ensure code uses dev_() reporting macros where necessary
- remove ABS_PRESSURE reporting, tslib can be fixed
- ensure timer is removed on driver exit
- move to using dev_pmops for power management
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Zytronic USB-attached capacitive touchscreen support within the generic
USB touchscreen driver.
Signed-off-by: NDaniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: NVincent Sanders <vince@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Function name is input_ff_destroy() and not input_ff_free()
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Use strlcat() to append a string to the previously created first part.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

On Zaurus, hx4700 and others pressure is reported inverted -- the lighter
the pressure, the bigger numerical value.
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

usb_kill_urb() in disconnect is not needed as unregistering will cause
close() to be called.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add a number of plafrom dependent parameters to atmel_tsadcc.  The
touchscreeen driver can now take into account the slight differences
that exist between IPs included in diferent products.  This will also
allow to adapt its behaivior to the caracteristics of the resistive
panel used.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Tiny patch for setting capabilities using input API function.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

The touchpad on Acer Aspire 5720, 5520 and some other Aspire models
(signature 0x73, 0x02, 0x50) has a button that can be rocked in 4
different directions. Make the driver to generate BTN_0..BTN_3 events
in response. The Synaptics driver by default maps BTN_0 and BTN_1 to
up and down, so there should be no visible changes with the old setup
that generated BTN_FORWARD and BTN_BACK (also mapped to up and down).
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>