Remove obsoleted "idex=reset" kernel parameter
(it has been obsoleted since 1 Nov 2004).

Then remove corresponding code from ide_probe_port()
and no longer used ->reset field from ide_hwif_t.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add "ignore_cable" parameter:

* "ide_core.ignore_cable=[interface_number]" boot option if IDE is built-in
  (i.e. "ide_core.ignore_cable=1" to force ignoring cable for "ide1")

* "ignore_cable=[interface_number]" module parameter (for ide_core module)
  if IDE is compiled as module

v2:
* Add ide_port_apply_params() helper
  - use it in ide_device_add_all() and ide_scan_port().

* Make it possible to later disable ignoring cable detection by passing
  "[interface_number]:0" to /sys/module/ide_core/parameters/ignore_cable
  (however sysfs interface is not enabled yet since it needs some other
   IDE changes to make it work reliable).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add struct ide_dma_ops and convert core code + drivers to use it.

While at it:

* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.

* Drop "ide_" "infixes" from DMA methods.

* au1xxx-ide.c:
  - use auide_dma_{test_irq,end}() directly in auide_dma_timeout()

* pdc202xx_old.c:
  - drop "old_" "infixes" from DMA methods

* siimage.c:
  - add siimage_dma_test_irq() helper
  - print SATA warning in siimage_init_one()

* Remove no longer needed ->init_hwif implementations.

v2:
* Changes based on review from Sergei:
  - s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
  - s/drive->hwif/hwif/ in idefloppy_pc_intr().
  - fix patch description w.r.t. au1xxx-ide changes
  - fix au1xxx-ide build
  - fix naming for cmd64*_dma_ops
  - drop "ide_" and "old_" infixes
  - s/hpt3xxx_dma_ops/hpt37x_dma_ops/
  - s/hpt370x_dma_ops/hpt370_dma_ops/
  - use correct DMA ops for HPT302/N, HPT371/N and HPT374
  - s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/

v3:
* Two bugs slipped in v2 (noticed by Sergei):
  - use correct DMA ops for HPT374 (for real this time)
  - handle HPT370/HPT370A properly
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_SERIALIZE_DMA host flag to serialize ports
  if DMA is available and handle it in ide_init_port().

* Convert sl82c105 host driver to use this new flag.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_hwif_setup_dma() return an error value.

* Pass 'const struct ide_port_info *d' instead of 'unsigned long dmabase'
  to ->init_dma method and make it return an error value.

* Rename ide_get_or_set_dma_base() to ide_pci_dma_base(),
  change ordering of its arguments and then export it.

* Export ide_pci_set_master().

* Do complete DMA setup inside ->init_dma method and update ->init_dma
  users accordingly.

* Sanitize code for DMA setup in ide_init_port().

v2:
* Fix for CONFIG_BLK_DEV_IDEDMA_PCI=n configs
  (from Jiri Slaby <jirislaby@gmail.com>):

  Fix following compiler warning by returning EINVAL:

  In file included from ANYTHING-INCLUDING-IDE.H:45:
  include/linux/ide.h: In function ‘ide_hwif_setup_dma’:
  include/linux/ide.h:1022: warning: no return statement in function returning non-void

Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

__FUNCTION__ is gcc-specific, use __func__

[bart: fix checkpatch.pl errors in ide-lib.c and ppc/mpc8xx.c while at it]
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It is no longer needed to set hwif->mmio flag to tell IDE layer to not
manage resources so cleanup host drivers that used hwif->mmio flag only
for this purpose.

Ditto for ide_legacy_init_one().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Reserve PCI BARs 0-3 (0-1 for single port controllers) in
  ide_pci_enable() and remove ide_hwif_request_regions() call
  from ide_device_add_all() (also cleanup resource management
  in scc_pata host driver).

* Fix handling of PCI BAR 4 in ide_pci_enable(), then cleanup
  ide_iomio_dma() (+ init_hwif_trm290() in trm290 host driver)
  and remove ide_release[_iomio]_dma().

v2:
* Fixup trm290 host driver.

v3:
* Because of scc_pata host driver changes we need to call
  pci_request_selected_regions() also in setup_mmio_scc().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Tell IDE layer to not manage resources by setting hwif->mmio flag.

* Use {request,release}_region() for resources management.

* Set ->name field of 'struct ide_port_info' instances in legacy VLB
  host drivers and use driver name for resources management.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move the common code for primary/seconary port setup from
ide_legacy_device_add() to ide_legacy_init_one().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Tell IDE layer to not manage resources by setting hwif->mmio flag.

* Use {request,release}_region() for resources management.

* Use driver name for resources management.

* Remove no longer needed 'hwif->chipset == ide_4drives' handling
  from ide_device_add_all().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'unsigned long config' argument to ide_legacy_device_add()
  for setting hwif->config_data.

* Use ide_find_port_slot() instead of ide_find_port() in
  ide_legacy_device_add().

* Handle IDE_HFLAG_QD_2ND_PORT and IDE_HFLAG_SINGLE host flags in
  ide_legacy_device_add().

* Convert qd65xx host driver to use ide_legacy_device_add().

v2:
* Update ali14xx, dtc2278, ht6560b and umc8672 host drivers.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_legacy_device_add() helper for use by legacy VLB host drivers
(+ convert them to use it).

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Update IDE PMAC host driver to use drive->noprobe instead of hwif->noprobe
and remove hwif->noprobe completely (it is always set to zero now).

There should be no functional changes caused by this patch.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move hooks for port/host specific methods from ide_hwif_t to
  'struct ide_port_ops'.

* Add 'const struct ide_port_ops *port_ops' to 'struct ide_port_info'
  and ide_hwif_t.

* Update host drivers and core code accordingly.

While at it:

* Rename ata66_*() cable detect functions to *_cable_detect() to match
  the standard naming. (Suggested by Sergei Shtylyov)

v2:
* Fix build for bast-ide. (Noticed by Andrew Morton)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_QD_2ND_PORT host flag to indicate the need of skipping
  first ide_hwifs[] slot for the second port of QD65xx controller.

* Handle this new host flag in ide_find_port_slot().

* Convert legacy VLB host drivers to use ide_find_port().

While at it:

* Fix couple of printk()-s in qd65xx host driver to not use hwif->name.

v2:
* Fix qd65xx.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Change ide_match_hwif() argument from 'u8 bootable' to
  'struct ide_port_info *d'.

* Move ide_match_hwif() to ide-probe.c from setup-pci.c and rename
  it to ide_find_port_slot().  Update some comments while at it.

* ide_find_port() can be now just a wrapper for ide_find_port_slot().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS to drivers/ide/Kconfig and use
  it instead of defining IDE_ARCH_OBSOLETE_DEFAULTS in <arch/ide.h>.

v2:
* Define ide_default_irq() in ide-probe.c/ns87415.c if not already defined
  and drop defining ide_default_irq() for CONFIG_IDE_ARCH_OBSOLETE_DEFAULTS=n.

  [ Thanks to Stephen Rothwell and David Miller for noticing the problem. ]

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_{ALTSTATUS,IREASON,BCOUNTL,BCOUNTH}_OFFSET defines.

* Remove IDE_*_REG macros - this results in more readable
  and slightly smaller code.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove obsoleted "idex=base[,ctl[,irq]]" kernel parameters
  and update Documentation/ide/ide.txt.

* Remove no longer needed ide_forced chipset type.

v2:
* is_chipset_set[] -> is_chipset_set in ide.c.

* Documentation/ide/ide.txt fix.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

request_irq() will fail if there is already another IRQ handler
registered and IRQ flags are mismatched.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'struct class ide_port_class' ('ide_port' class) and a 'struct
  device *portdev' ('ide_port' class device) in ide_hwif_t.

* Register 'ide_port' class in ide_init() and unregister it in
  cleanup_module().

* Create ->portdev in ide_register_port () and unregister it in
  ide_unregister().

* Add "delete_devices" class device attribute for unregistering IDE devices
  on a port and "scan" one for probing+registering IDE devices on a port.

* Add ide_sysfs_register_port() helper for registering "delete_devices"
  and "scan" attributes with ->portdev.  Call it in ide_device_add_all().

* Document IDE warm-plug support in Documentation/ide/warm-plug-howto.txt.

v2:
* Convert patch from using 'struct class_device' to use 'struct device'.
  (thanks to Kay Sievers for doing it)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Rework PowerMac media-bay support in such way that instead of
un/registering the IDE interface we un/register IDE devices:

* Add ide_port_scan() helper for probing+registerering devices on a port.

* Rename ide_port_unregister_devices() to __ide_port_unregister_devices().

* Add ide_port_unregister_devices() helper for unregistering devices on a port.

* Add 'ide_hwif_t *cd_port' to 'struct media_bay_info', pass 'hwif' instead
  of hwif->index to media_bay_set_ide_infos() and use it to setup 'cd_port'.

* Use ide_port_unregister_devices() instead of ide_unregister()
  and ide_port_scan() instead of ide_register_hw() in media_bay_step().

* Unexport ide_register_hw() and make it static.

v2:
* Fix build by adding <linux/ide.h> include to <asm-powerpc/mediabay.h>.
  (Reported by Michael/Kamalesh/Andrew).

Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_cfg_mtx lock/unlock to ide_port_setup_devices() and then move
ide_port_setup_devices() call from init_irq() to ide_device_add_all().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

IDE devices need to be removed from /proc/ide/ _before_ being unregistered:

* Drop 'ide_hwif_t *hwif' argument from destroy_proc_ide_device()
  and use drive->hwif instead.

* Rename destroy_proc_ide_device() to ide_proc_unregister_device().

* Call ide_proc_unregister_device() in drive_release_dev().

* Remove no longer needed destroy_proc_ide_drives().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out cable detection from ide_init_port() to ide_port_cable_detect().

* Move ide_port_cable_detect() call to ide_device_add_all().
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This reverts commit b140b99c.

[ conflict in drivers/ide/ide-probe.c fixed manually ]

It turned out that probing order change causes problems for some drives:

	http://bugzilla.kernel.org/show_bug.cgi?id=10239

Since root causes are still being investigated and are unlikely to be fixed
before 2.6.25 lets revert this change for now.  As a result cable detection
becomes less reliable when compared with 2.6.24 but the affected drives are
useable again.
Reported-by: NRichard Genoud <richard.genoud@gmail.com>
Bisected-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Skip probing port if "hdx=noprobe" parameter was used for both devices on it.

* Obsolete "idex=noprobe" parameter - it only works for ide_generic, cmd640
  and PCI hosts in Compatibility mode (on alpha/x86/ia64/m32r/mips/ppc32).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

APUS support is gone...
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Sunday 10 February 2008, Atsushi Nemoto wrote:
> On Sun, 06 Jan 2008 18:03:10 +0100, Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> wrote:
> > +	/* reset DMA masks only for SFF-style DMA controllers */
> > +	if ((d->host_flags && IDE_HFLAG_NO_DMA) == 0 && hwif->dma_base == 0)
> > +		hwif->swdma_mask = hwif->mwdma_mask = hwif->ultra_mask = 0;
> 
> It might be too late, but "host_flags && IDE_HFLAGS_NO_DMA" seems
> wrong for me.

Fix regression caused by commmit c413b9b9
("ide: add struct ide_port_info instances to legacy host drivers").
Reported-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

After the APUS removal, some code can be removed.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Karsten Keil <kkeil@suse.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Cache value read from the Status register in 'stat' variable in do_probe()
  and enable_nest(), then remove remove needless Status register reads.

While at it:

* Add proper KERN_* levels to printk() calls.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Un-static create_proc_ide_drives() and call it from ide_device_add_all().

While at it:
* Rename create_proc_ide_drives() to ide_proc_port_register_devices().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move hwif->present check out from ide_proc_register_port() to
ide_device_add_all().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out devices setup from ide_acpi_init() to
  ide_acpi_port_init_devices().

* Call ide_acpi_port_init_devices() in ide_device_add_all().

While at it:
* Remove no longer needed 'drive' field from struct ide_acpi_drive_link.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out devices setup from init_irq() to ide_port_setup_devices().

While at it:
* Do devices setup after printing port information.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Factor out adding drive to hwgroup from init_irq() to
ide_add_drive_to_hwgroup().

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>