v2: Allow to have or omit space before platform

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205190118.7088-1-lucas.demarchi@intel.com

Starting on GLK we support HDMI 2.0. So this patch only
extend the work Shashank has made to GLK to CNL.

v2: The version that compiles :/
v3: Invert order to newer || older platforms check. (Ville).

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115184205.8104-1-rodrigo.vivi@intel.com

Remove intel_digital_port->port and replace its users with
intel_encoder->port. intel_encoder->port is a superset of
intel_digital_port->port, and it works correctly even for
MST encoders.

v2: Eliminate a few dp_to_dig_port()->base.port cases too (DK)

Performed with cocci:
@@
@@
struct intel_digital_port {
       ...
-       enum port port;
       ...
}

@@
struct intel_digital_port *D;
expression E;
@@
- D->port = E;

@@
struct intel_digital_port *D;
@@
- D->port
+ D->base.port

@
expression E;
@@
(
- dp_to_dig_port(E)->port
+ dp_to_dig_port(E)->base.port
|
- enc_to_dig_port(E)->port
+ to_intel_encoder(E)->port
)

@@
expression E;
@@
- to_intel_encoder(&E->base)
+ E

@@
struct intel_digital_port *D;
identifier I, M;
@@
  I = &D->base
<...
(
- D->base.M
+ I->M
|
- &D->base
+ I
)
...>

@@
identifier D;
expression E;
identifier M;
@@
 D = enc_to_dig_port(&E->base)
<...
(
- D->base.M
+ E->M
|
- &D->base
+ E
)
...>

@@
identifier D, DP;
expression E;
identifier M;
@@
 DP = enc_to_intel_dp(&E->base)
<...
(
- dp_to_dig_port(DP)->base.M
+ E->M
|
- &dp_to_dig_port(DP)->base
+ E
)
...>

@@
expression E;
identifier M;
@@
(
- enc_to_dig_port(&E->base)->base.M
+ E->M
|
- enc_to_dig_port(&E->base)->base
+ E
|
- enc_to_mst(&E->base)->primary->base.port
+ E->port
)

@@
expression E;
identifier D;
@@
- struct intel_digital_port *D = E;
... when != D

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171109152434.32074-1-ville.syrjala@linux.intel.com

Rather than digging through encoder->crtc and crtc->config in the
DPIO PHY functions, pass down the correct crtc state from the caller.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031205123.13123-6-ville.syrjala@linux.intel.comAcked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>

Explicitly pass the crtc and connector states into the audio
code enable/disable hooks, and plumb them all the way down.

This gets rid of almost all crtc->config and encoder->crtc
uses. The one place where we still use them is
i915_audio_component_sync_audio_rate() since that gets called from
the audio driver and we don't have explicit states around then.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171030184654.17429-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Currently the DDI encoder->type will change at runtime depending on
what kind of hotplugs we've processed. That's quite bad since we can't
really trust that that current value of encoder->type actually matches
the type of signal we're trying to drive through it.

Let's eliminate that problem by declaring that non-eDP DDI port will
always have the encoder type as INTEL_OUTPUT_DDI. This means the code
can no longer try to distinguish DP vs. HDMI based on encoder->type.
We'll leave eDP as INTEL_OUTPUT_EDP, since it'll never change and
there's a bunch of code that relies on that value to identify eDP
encoders.

We'll introduce a new encoder .compute_output_type() hook. This allows
us to compute the full output_types before any encoder .compute_config()
hooks get called, thus those hooks can rely on output_types being
correct, which is useful for cloning on oldr platforms. For now we'll
just look at the connector type and pick the correct mode based on that.
In the future the new hook could be used to implement dynamic switching
between LS and PCON modes for LSPCON.

v2: Fix BXT/GLK PPS explosion with DSI/MST encoders
v3: Avoid the PPS warn on pure HDMI/DVI DDI encoders by checking dp.output_reg
v4: Rebase
v5: Populate output_types in .get_config() rather than in the caller
v5: Split out populating output_types in .get_config() (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-3-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Rather than having the caller of .get_config() set output_types based on
encoder->type, let's just have .get_config() itself populate
output_types. This way we are isolated from encoder->type, which won't
be useable for this purpose anyway soon (at least for DDI encoders).

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-2-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Starting from version 204 VBT can specify the max TMDS clock we are
allowed to use with HDMI ports. Parse that information and take it
into account when filtering modes and computing a crtc state.

Also take the opportunity to sort the platform check if ladder
from new to old.

v2: Add defines for the values into intel_vbt_defs.h (Jani)
    Don't fall back to 0 silently for unknown values (Jani)
    Skip the debug print for the 0 case (Jani)

Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171030145702.23662-1-ville.syrjala@linux.intel.com

Move the crtc state related 12bpc checks into hdmi_12bpc_possible()
since that one already examines other parts of the crtc state.

Note that we can drop the !force_dvi check since
crtc_state->has_hdmi_sink already accounts for that.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026151405.30710-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Now that the infoframe hooks are part of the intel_dig_port, we can use
the normal .write_infoframe() hook to update the VSC SDP. We do need to
deal with the size difference between the VSC DIP and the others though.

Another minor snag is that the compiler will complain to use if we keep
using enum hdmi_infoframe_type type and passing in the DP define instead,
so et's just change to unsigned int all over for the inforframe type.

v2: Rebase due to other PSR changes
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171013194051.19286-1-ville.syrjala@linux.intel.com

The enable/disable/etc. encoder hooks aren't supposed to alter the
state(s), so pass them as const. Unfortunately C lacks any kind of deep
const thingy, so this can't catch all abuses. But at least it acts as a
hint to the reader telling them not to mess about with the state(s).

v2: Update intel_tv_mode_find() and ironlake_edp_pll_on() as well
v3: Deal with intel_sdvo_connector_state
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-9-ville.syrjala@linux.intel.com

DP ports may want to use the video DIP for SDP transmission, so let's
initialize the vfuncs for DP encoders as well. The only exception is
port A eDP prior to HSW as that one doesn't have a video DIP instance.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-6-ville.syrjala@linux.intel.com

DP ports will also want to utilize the video DIP for SDP transmission.
So let's move the vfuncs into the dig_port.

v2: Rebase due to DDI changes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-5-ville.syrjala@linux.intel.com

has_infoframe is what tells us whether infoframes should be enabled, so
let's pass that instead of has_hdmi_sink to .set_infoframes().
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-3-ville.syrjala@linux.intel.com

Cleanup the code. Map the pins in accordance to
individual platforms rather than according to ports.
Create separate functions for platforms.

v2:
 - Add missing condition for CoffeeLake. Make platform
 specific functions static. Add function
 i915_ddc_pin_mapping().

v3:
 - Rename functions to x_port_to_ddc_pin() which directly
   indicates the purpose. Correct default return values on CNP
   and BXT. Rename i915_port_to_ to g4x_port_to since that was
   the first platform to run this. Correct code style. (Paulo)

Sugested-by Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1502927114-24012-1-git-send-email-anusha.srivatsa@intel.com

The idea is to have an unique place to decide the pin-port
per platform.

So let's create this function now without any functional
change. Just adding together code from hdmi and dp together.

v2: Add missing pin for port A.
v3: Fix typo on subject.
    Avoid behaviour change so add WARN_ON and return
    if port A on HDMI. (by DK).

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170811182650.14327-2-rodrigo.vivi@intel.com

It's dead code, the core handles all this directly now.

The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.

v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.chAcked-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NArchit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Acked-by: NNoralf Trønnes <noralf@tronnes.org>
Acked-by: NVincent Abriou <vincent.abriou@st.com>

It's dead code, the core handles all this directly now. This also
allows us to unexport drm_atomic_helper_connector_set_property.

The only special case is nouveau which used one function for both
pre-nv50 legacy modeset code and post-nv50 atomic world instead of 2
vtables. But amounts to exactly the same.

What is rather strange here is how few drivers set this up, I suspect
the earlier patch to handle properties in the core did end up fixing a
pile of possible issues.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-7-daniel.vetter@ffwll.chAcked-by: NVincent Abriou <vincent.abriou@st.com>

This patch sets the is_hdmi2_src identifier in drm connector
for GLK platform. GLK contains a native HDMI 2.0 controller.
This identifier will help the EDID handling functions to save
lot of work which is specific to HDMI 2.0 sources.

V3: Added this patch
V4: Rebase
V4: Rebase
V5: Added r-b from Ander
V6: Rebase
V7: Rebase
V8: Rebase
V9: Added r-b from Ville
V9: Added r-b from Imre

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-7-git-send-email-shashank.sharma@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When output colorspace is YCBCR420, we have to load the
corresponding colorspace in AVI infoframe. This patch fills
the colorspace of AVI infoframe as per the output mode.

V2: Rebase
V3: Rebase
V4: Rebase
V5: Added r-b from Ander
V6: Checking RGB/YCBCR420 output only (Ville)
V7: Add colorspace info in driver(not drm layer) (Ville)
V8: Rebase
V9: Added r-b from Ville
V10: Added r-b from Imre

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-6-git-send-email-shashank.sharma@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
  blend mode to use the scaler in 5x3 ratio (bits 26 and 27)

This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.

V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
    - Add readouts for state->ycbcr420 and 420 pixel_clock.
    - Handle warning due to mismatch in clock for ycbcr420 clock.
    - Rename PIPEMISC macros to match the Bspec.
    - Add a debug print stating if YCBCR 4:2:0 output enabled.
    Added r-b from Ville
V9: Addressed review comments from Imre:
    - Add 420 mode clock adjustment in intel_hdmi_mode_valid to
      prevent 420_only modes getting rejected for high clock.
    - Add port clock adjustment for ycbcr420 modes in ddi_get_clock
    - Rename macros as per Ville's suggestion.
    - Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
     from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

To get a YCBCR420 output from intel platforms, we need one
scaler to scale down YCBCR444 samples to YCBCR420 samples.

This patch:
- Does scaler allocation for HDMI ycbcr420 outputs.
- Programs PIPE_MISC register for ycbcr420 output.

V2: rebase
V3: rebase
V4: rebase
V5: addressed review comments from Ander:
    - No need to check both scaler_user && hdmi_output.
      Check for scaler_user is enough.
V6: rebase
V7: Do not create a new scaler user, use existing pipe scaler user.
V8: rebase
V9: Addressed review comments from Ville:
    - Remove leftover comment for HDMI scaler user.
    - Remove unnecessary blank line.
    - Make scaler alocation failure a DEBUG log instead of ERROR.
    Added r-b from Ville
V10: Update commit message as per latest code (Imre)
     Added r-b from Imre

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-3-git-send-email-shashank.sharma@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch checks encoder level support for YCBCR420 outputs.
The logic goes as simple as this:
If the input mode is YCBCR420-only mode: prepare HDMI for
YCBCR420 output, else continue with RGB output mode.

It checks if the mode is YCBCR420 and source can support this
output then it marks the ycbcr_420 output indicator into crtc
state, for further staging in driver.

V2: Split the patch into two, kept helper functions in DRM layer.
V3: Changed the compute_config function based on new DRM API.
V4: Rebase
V5: Rebase
V6: Check and handle YCBCR420-only modes, discard the property
    based approach (Ville)
V7: Addressed review comments from Ville
    - add else case in 12BPC check.
    - extract ycbcr420 state inside hdmi_12bpc_possible function.
V8: Addressed review comments from Ville
    - Remove extra blank lines.
    - Remove "HDMI" from the description of ycbcr420 state variable.
    - Remove local variable, use crtc_state->ycbcr420 instead.
    Added r-b from Ville.
V9: Rebase
V10: Added r-b from Imre

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NVille Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500650709-14447-2-git-send-email-shashank.sharma@intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).

This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.

This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.

In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
	- VIC for 4K modes for HDMI 1.4 sinks
	- S3D information for S3D modes
  As CEA-861-F has already defined VICs for 4K videomodes, this
  patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
  until the mode is 3D.

Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>

PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c

V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
	- Do not send VICs in both AVI-IF and HDMI-IF
	  send only one of it.
V4: Rebase
V5: Added r-b from Neil.
    Addressed review comments from Ville
    - Do not block HDMI vendor IF, instead check for VIC while
      handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

for_each_connector_in_state will be removed, so use the right state
here.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170712081344.25495-7-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On CNP PCH based platforms the gmbus is on the south display that
is on PCH. The existing implementation for previous platforms
already covers the need for CNP expect for the pin pair configuration
that follows similar definitions that we had on BXT.

v2: Don't drop "_BXT" as the indicator of the first platform
    supporting this pin numbers. Suggested by Daniel.
v3: Add missing else and fix register table since CNP GPIO_CTL
    starts on 0xC5014.
v4: Fix pin number and map according to the current available VBT.
    Re-add pin 4 for port D. Lost during some rebase.
v5: Use table as spec. If VBT is wrong it should be ignored.

Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com

intel_hdmi supports 3 properties, force_audio, broadcast rgb and
scaling mode. The last one is only created for eDP, so the is_eDP
in set_property is not required.

panel fitting and broadcast rgb are straightforward and only requires
changing compute_config.

force_audio is also used to force DVI mode, which means changes to
compute_config and mode_valid. mode_valid is called with
connection_mutex held, so it can safely dereference connector->state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-11-maarten.lankhorst@linux.intel.com

This is only used in i915, which had used its own non-atomic way to
deal with the picture aspect ratio. Move selected aspect_ratio to
atomic state and use the atomic state in the affected i915 connectors.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170501133804.8116-2-maarten.lankhorst@linux.intel.com
[mlankhorst: taomic -> atomic thanks to Manasi's input]
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display workaround #1139 for Geminilake instructs us to restrict HDMI
to 8 bpc when htotal is greater than 5460. Otherwise, the pipe is unable
to generate a proper signal and is left in a state where corruption is
seen with other modes.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100440
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NShashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170424104718.26448-1-ander.conselvan.de.oliveira@intel.com

Noticed this while I was looking at some debug output,
 [drm:intel_hdmi_compute_config [i915]] picking bpc to 12 for HDMI output
 [drm:intel_hdmi_compute_config [i915]] forcing pipe bpc to 36 for HDMI

I believe the second line should be pipe *bpp*
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491329765-14340-1-git-send-email-dhinakaran.pandiyan@intel.com

Geminilake has a native HDMI 2.0 controller, which is capable of
driving clocks upto 594Mhz. This patch updates the max tmds clock
limit for the same.

V2: rebase
V3: rebase
V4: added r-b from Ander
V5: rebase
V6: rebase
V7: rebase
V8: rebase
V9: rebase
V10: rebase

Cc: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Reviewed-by: NAnder Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-7-git-send-email-shashank.sharma@intel.com

Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.

V2: Addressed review comments from Ville:
 - Do not track scrambling status in DRM layer, track somewhere in
   driver like in intel_crtc_state.
 - Don't talk to monitor at such a low layer, set monitor scrambling
   in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
 - In comments, function names, use "sink" instead of "monitor",
   so that the implementation could be close to the language of
   HDMI spec.

V4: Addressed review comment from Maarten
 - scrambling -> hdmi_scrambling
 - high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
 - Do not modifiy the crtc_state after compute_config. Move all
   scrambling and tmds_clock_ratio calcutations to compute_config.
 - While setting scrambling for source/sink, do not check the
   conditions again, just go by the crtc_state flags. This will
   simplyfy the condition checks.

V6: Addressed review comments from Ville
 - Do not add IS_GLK check in disable/enable function, instead add it
   in compute_config, while setting state flags.
 - Remove unnecessary paranthesis.
 - Simplyfy handle_sink_scrambling function as suggested.
 - Add readout code for scrambling status in get_ddi_config and add a
   check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
 - No separate function for source scrambling, make it inline
 - Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
 - Do not add platform check while setting source scrambling
 - Use pipe_config instead of crtc->config to set sink scrambling
 - To readout scrambling status, Compare with SCRAMBLING_MASK
   not any of its bits
 - Remove platform check in intel_pipe_config_compare while checking
   scrambling status

V8: Fixed mege conflict, Addressed review comments from Ander
 - Remove the desciption/comment about scrambling fom the caller, move
   it to the function
 - Move the IS_GLK check into scrambling function
 - Fix alignment

V9: Fixed review comments from Ville, Ander
 - Pass the scrambling state variables as bool input to the sink_scrambling
   function and let the disable call be unconditional.
 - Fix alignments in function calls and debug messages.
 - Add kernel doc for function intel_hdmi_handle_sink_scrambling

V10: Rebase
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com

Check that the sink really declared 12bpc support before we enable it.
This should not actually never happen since it's mandatory for HDMI
sinks to support 12bpc if they support any deep color modes. But
reality disagrees with the theory and there are actually sinks in
the wild that violate the spec.

v2: Fix the output_types check
    Update commit message to state that these things are in fact real

Cc: stable@vger.kernel.org
Cc: Nicholas Sielicki <nicholas.sielicki@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99250Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213175818.24958-1-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit c750bdd3)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Check that the sink really declared 12bpc support before we enable it.
This should not actually never happen since it's mandatory for HDMI
sinks to support 12bpc if they support any deep color modes. But
reality disagrees with the theory and there are actually sinks in
the wild that violate the spec.

v2: Fix the output_types check
    Update commit message to state that these things are in fact real

Cc: stable@vger.kernel.org
Cc: Nicholas Sielicki <nicholas.sielicki@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99250Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213175818.24958-1-ville.syrjala@linux.intel.comReviewed-by: NShashank Sharma <shashank.sharma@intel.com>

The encoder power domain is obviously tied to the encoder, so store it
in struct intel_encoder. This avoids some indirection.

v2: Rebase
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170222063431.10060-3-ander.conselvan.de.oliveira@intel.com

Remove workaround for swapped HPD pins in broxton A stepping, which is
pre-production hardware.

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203140316.20792-1-ander.conselvan.de.oliveira@intel.com

HDMI 2.0 recommends that we set the Q bits in the AVI infoframe
even when the sink does not support quantization range selection (QS=0).
According to CEA-861 we can do that as long as the Q we send matches
the default quantization range for the mode.

Previously I think I had misread the spec as saying that you can't
send a non-zero Q at all when QS=0. But that's not what the spec
actually says.

v2: Fix typo in commit message (Jani)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-5-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Pull the logic to populate the quantization range information
in the AVI infoframe into a small helper. We'll be adding a bit
more logic to it, and having it in a central place seems like a
good idea since it's based on the CEA-861 spec.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111125725.8086-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Make the code selecting the RGB quantization range a little less magicy
by wrapping it up in a small helper.

v2: s/adjusted_mode/mode in vc4 to make it actually compile
v3: Add a comment proposed by Eric
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111141835.25369-1-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NEric Anholt <eric@anholt.net>

Notifiations like mode change, hot plug and edid to
the audio driver are added. This is inturn used by the
audio driver for its functionality.

A new interface file capturing the notifications needed by the
audio driver is added
Signed-off-by: NPierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: NJerome Anand <jerome.anand@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>