for restore-inhibit context, hardware will not load in-context mmios
(engine context part) to hardware, but hardware will save the mmio
values in hardware back to context image. So, in order to save correct
values of vGPU back to context image, values of vGPU mmios have to be
loaded into hardware first for restore-inhibit context.

In this patch, the mechanism is applied to all gen9 platform.

The reason excluding gen8 platforms is only because of lacking of testing
on those platforms.

v3: for mocs registers, goto in-context mmios save-restore path for skl
platform as well (weinan li)
v2: update vreg when scanning indirect context for inhibit context for
gen9

Cc: Weinan Li <weinan.z.li@intel.com>
Acked-by: NWeinan Li <weinan.z.li@intel.com>
Signed-off-by: NYan Zhao <yan.y.zhao@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

"To track whether a request has started on HW, we can emit a breadcrumb at
the beginning of the request and check its timeline's HWSP to see if the
breadcrumb has advanced past the start of this request." It means all the
request which timeline's has_init_breadcrumb is true, then the
emit_init_breadcrumb process must have before emitting the real commands,
otherwise, the scheduler might get a wrong state of this request during
reset. If the request is exactly the guilty one, the scheduler won't
terminate it with the wrong state. To avoid this, do emit_init_breadcrumb
for all the requests from gvt.

v2: cc to stable kernel

Fixes: 85474441 ("drm/i915: Identify active requests")
Cc: stable@vger.kernel.org
Acked-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NWeinan <weinan.z.li@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

In commit b7404c7e ("drm/i915: Bump ready tasks ahead of
busywaits"), I tried cutting a corner in order to not install a signal
for each of our dependencies, and only listened to requests on which we
were intending to busywait. The compromise that was made was that
instead of then being able to promote the request with a full
NOSEMAPHORE like its non-busywaiting brethren, as we had not ensured we
had cleared the semaphore chain, we settled for only using the NEWCLIENT
boost. With an over saturated system with multiple NEWCLIENTS in flight
at any time, this was found to be an inadequate promotion and left us
with a much poorer scheduling order than prior to using semaphores.

The outcome of this patch, is that all requests have NOSEMAPHORE
priority when they have no dependencies and are ready to run and not
busywait, restoring the pre-semaphore ordering on saturated systems.

We can demonstrate the effect of poor scheduling order by oversaturating
the system using gem_wsim on a system with multiple vcs engines
(i.e running the same workloads across more clients than required for
peak throughput, e.g. media_load_balance_17i7.wsim -c4 -b context):

x v5.1 (normalized)
+ tip
* fix
+------------------------------------------------------------------------+
|                                                                    x   |
|                                                                    x   |
|                                                                    x   |
|                                                                    x   |
|                                                                   %x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %%x   |
|                                                                  %#x   |
|                                                                  %#x   |
|                                                                  %#x   |
|                                                                  %#x   |
|                                                                  %#x   |
|         +                                                        %#xx  |
|         +                                                        %#xx  |
|         +                                                       %%#xx  |
|         +                                                       %%#xx  |
|         +                                                       %%#xx  |
|         +                                                       %%#xx  |
|         +                                                       %%##x  |
|         +++                                                     %%##x  |
|         +++                                                     %%##x  |
|         +++                                                     %%##x  |
|        ++++                                                     %%##x  |
|        ++++                                                     %%##x  |
|        ++++                                                     %%##xx |
|        ++++                                                     %###xx |
|        ++++                                                     %###xx |
|        ++++                                                     %###xx |
|        ++++                                                     %###xx |
|        ++++ +                                                   %#O#xx |
|        ++++ +                                                   %#O#xx |
|        ++++++ +                                                 %#O#xx |
|       ++++++++++                                                %OOOxxx|
|       ++++++++++       +                                       %#OOO#xx|
|     + ++++++++++++ ++ +++++    +                        ++    @@OOOO#xx|
|                                                                   |A_| |
||__________M_______A____________________|                               |
|                                                                 |A_|   |
+------------------------------------------------------------------------+
    N           Min           Max        Median           Avg        Stddev
x 120       0.99456       1.00628      0.999985     1.0001545  0.0024387139
+ 120      0.873021       1.00037      0.884134    0.90148752   0.039190862
Difference at 99.5% confidence
	-0.098667 +/- 0.0110762
	-9.86517% +/- 1.10745%
	(Student's t, pooled s = 0.0277657)
% 120      0.990207       1.00165     0.9970265    0.99699748     0.0021024
Difference at 99.5% confidence
	-0.003157 +/- 0.000908245
	-0.315651% +/- 0.0908105%
	(Student's t, pooled s = 0.00227678)

Fixes: b7404c7e ("drm/i915: Bump ready tasks ahead of busywaits")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-2-chris@chris-wilson.co.uk
(cherry picked from commit 17db337f)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Commit 1413b2bc ("drm/i915: Trim NEWCLIENT boosting") had the
intended consequence of not allowing a sequence of work that merely
crossed into a new engine the privilege to be promoted to NEWCLIENT
status. It also had the unintended consequence of actually making
NEWCLIENT effective on heavily oversubscribed transcode machines and
impacting upon their throughput.

If we consider a client packet composed of (rcsA, rcsB, vcs) and 30 of
those clients, using the NEWCLIENT boost that will be scheduled as

	rcsA x 30, (rcsB, vcs) x 30

where as before it would have been

	(rcsA, rcsB, vcs) x 30

That is with NEWCLIENT only boosting the first request of each client,
we would execute all rcsA requests prior to running on the vcs engines;
acruing a lot of dead time as compared to the previous case where the
vcs engine would be started in parallel to processing the second client.

The previous patch has the effect of delaying submission until it is
required by a third party (either the user with an explicit wait, or by
another client/engine). We reduce the NEWCLIENT bump to a mere WAIT,
which has the effect of removing its preemptive grant and reducing it to
the same level as any other user interaction -- that it will not be
promoted above the interengine dependencies, and so preventing NEWCLIENTS
from starving other engines. This a large nerf to the rrul properties of
the current NEWCLIENT, but it still does give prioritised submission to
new requests from light workloads.

References: b16c7651 ("drm/i915: Priority boost for new clients")
Fixes: 1413b2bc ("drm/i915: Trim NEWCLIENT boosting") # customer impact
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Dmitry Ermilov <dmitry.ermilov@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-4-chris@chris-wilson.co.uk
(cherry picked from commit 68fc728b)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

The handling of the no-preemption priority level imposes the restriction
that we need to maintain the implied ordering even though preemption is
disabled. Otherwise we may end up with an AB-BA deadlock across multiple
engine due to a real preemption event reordering the no-preemption
WAITs. To resolve this issue we currently promote all requests to WAIT
on unsubmission, however this interferes with the timeslicing
requirement that we do not apply any implicit promotion that will defeat
the round-robin timeslice list. (If we automatically promote the active
request it will go back to the head of the queue and not the tail!)

So we need implicit promotion to prevent reordering around semaphores
where we are not allowed to preempt, and we must avoid implicit
promotion on unsubmission. So instead of at unsubmit, if we apply that
implicit promotion on adding the dependency, we avoid the semaphore
deadlock and we also reduce the gains made by the promotion for user
space waiting. Furthermore, by keeping the earlier dependencies at a
higher level, we reduce the search space for timeslicing without
altering runtime scheduling too badly (no dependencies at all will be
assigned a higher priority for rrul).

v2: Limit the bump to external edges (as originally intended) i.e.
between contexts and out to the user.

Testcase: igt/gem_concurrent_blit
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515130052.4475-3-chris@chris-wilson.co.uk
(cherry picked from commit 6e7eb7a8)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

To simplify the next patch, update bump_priority and schedule to accept
the internal i915_sched_ndoe directly and not expect a request pointer.

add/remove: 0/0 grow/shrink: 2/1 up/down: 8/-15 (-7)
Function                                     old     new   delta
i915_schedule_bump_priority                  109     113      +4
i915_schedule                                 50      54      +4
__i915_schedule                              922     907     -15

v2: Adopt node for the old rq local, since it no longer is a request but
the origin node.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-2-chris@chris-wilson.co.uk
(cherry picked from commit 52c76fb1)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

To avoid pulling in a forward declaration in the next patch, move the
i915_sched_node handling to after the main dfs of the scheduler.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513120102.29660-1-chris@chris-wilson.co.uk
(cherry picked from commit 5ae87063)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.

Having whitespaces after -I does not matter since commit 48f6e3cf
("kbuild: do not drop -I without parameter").

[1]: https://patchwork.kernel.org/patch/9632347/Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.

Having whitespaces after -I does not matter since commit 48f6e3cf
("kbuild: do not drop -I without parameter").

[1]: https://patchwork.kernel.org/patch/9632347/Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NSakari Ailus <sakari.ailus@linux.intel.com>

I was able to build without these extra header search paths.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

i2c_new_dummy is typically called from the probe function of the
driver for the primary i2c client. It requires calls to
i2c_unregister_device in the error path of the probe function and
in the remove function.
This can be simplified by introducing a device-managed version.

Note the changed error case return value type: i2c_new_dummy returns
NULL whilst devm_i2c_new_dummy_device returns an ERR_PTR.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
[wsa: rename new functions and fix minor kdoc issues]
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NPeter Rosin <peda@axentia.se>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Currently i2c_new_device and i2c_new_dummy return just NULL in error
case although they have more error details internally. Therefore move
the functionality into new functions returning detailed errors and
add wrappers for compatibility with the current API.

This allows to use these functions with detailed error codes within
the i2c core or for API extensions.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
[wsa: rename new functions and fix minor kdoc issues]
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NPeter Rosin <peda@axentia.se>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The following commit:

  38ac0287 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB")

updated the EFI framebuffer code to use memory mappings for the linear
framebuffer that are permitted by the memory attributes described by the
EFI memory map for the particular region, if the framebuffer happens to
be covered by the EFI memory map (which is typically only the case for
framebuffers in shared memory). This is required since non-x86 systems
may require cacheable attributes for memory mappings that are shared
with other masters (such as GPUs), and this information cannot be
described by the Graphics Output Protocol (GOP) EFI protocol itself,
and so we rely on the EFI memory map for this.

As reported by James, this breaks some x86 systems:

  [ 1.173368] efifb: probing for efifb
  [ 1.173386] efifb: abort, cannot remap video memory 0x1d5000 @ 0xcf800000
  [ 1.173395] Trying to free nonexistent resource <00000000cf800000-00000000cf9d4bff>
  [ 1.173413] efi-framebuffer: probe of efi-framebuffer.0 failed with error -5

The problem turns out to be that the memory map entry that describes the
framebuffer has no memory attributes listed at all, and so we end up with
a mem_flags value of 0x0.

So work around this by ensuring that the memory map entry's attribute field
has a sane value before using it to mask the set of usable attributes.
Reported-by: NJames Hilliard <james.hilliard1@gmail.com>
Tested-by: NJames Hilliard <james.hilliard1@gmail.com>
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org> # v4.19+
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 38ac0287 ("fbdev/efifb: Honour UEFI memory map attributes when ...")
Link: http://lkml.kernel.org/r/20190516213159.3530-2-ard.biesheuvel@linaro.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

The Linux kernel will auto-disables all boot consoles whenever it
gets a preferred real console.

Currently on RISC-V systems, if we have a real console which is not
RISCV SBI console then boot consoles (such as earlycon=sbi) are not
auto-disabled when a real console (ttyS0 or ttySIF0) is available.
This results in duplicate prints at boot-time after kernel starts
using real console (i.e. ttyS0 or ttySIF0) if "earlycon=" kernel
parameter was passed by bootloader.

The reason for above issue is that RISCV SBI console always adds
itself as preferred console which is causing other real consoles
to be not used as preferred console.

Ideally "console=" kernel parameter passed by bootloaders should
be the one selecting a preferred real console.

This patch fixes above issue by not forcing RISCV SBI console as
preferred console.

Fixes: afa6b1cc ("tty: New RISC-V SBI console driver")
Cc: stable@vger.kernel.org
Signed-off-by: NAnup Patel <anup.patel@wdc.com>
Reviewed-by: NAtish Patra <atish.patra@wdc.com>
Signed-off-by: NPalmer Dabbelt <palmer@sifive.com>

The devm_ioremap_resource() function doesn't retunr NULL, it returns
error pointers.

Fixes: ecc133c6 ("soc: ixp4xx: qmgr: Pass resources")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Signed-off-by: NSheetal Singala <2396sheetal@gmail.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

This message should better identify the DM device with the integrity
failure.
Signed-off-by: NMilan Broz <gmazyland@gmail.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The information about tag size should not be printed without debug info
set. Also print device major:minor in the error message to identify the
device instance.

Also use rate limiting and debug level for info about used crypto API
implementaton.  This is important because during online reencryption
the existing message saturates syslog (because we are moving hotzone
across the whole device).

Cc: stable@vger.kernel.org
Signed-off-by: NMilan Broz <gmazyland@gmail.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The dm_early_create() function (which deals with "dm-mod.create=" kernel
command line option) calls dm_hash_insert() who gets an extra reference
to the md object.

In case of failure, this reference wasn't being released, causing
dm_destroy() to hang, thus hanging the whole boot process.

Fix this by calling __hash_remove() in the error path.

Fixes: 6bbc923d ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org
Signed-off-by: NHelen Koike <helen.koike@collabora.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Now that we've gotten rid of clk_readl() we can remove io.h from the
clk-provider header and push out the io.h include to any code that isn't
already including the io.h header but using things like readl/writel,
etc.

Found with this grep:

  git grep -l clk-provider.h | grep '.c$' | xargs git grep -L 'linux/io.h' | \
  	xargs git grep -l \
	-e '\<__iowrite32_copy\>' --or \
	-e '\<__ioread32_copy\>' --or \
	-e '\<__iowrite64_copy\>' --or \
	-e '\<ioremap_page_range\>' --or \
	-e '\<ioremap_huge_init\>' --or \
	-e '\<arch_ioremap_pud_supported\>' --or \
	-e '\<arch_ioremap_pmd_supported\>' --or \
	-e '\<devm_ioport_map\>' --or \
	-e '\<devm_ioport_unmap\>' --or \
	-e '\<IOMEM_ERR_PTR\>' --or \
	-e '\<devm_ioremap\>' --or \
	-e '\<devm_ioremap_nocache\>' --or \
	-e '\<devm_ioremap_wc\>' --or \
	-e '\<devm_iounmap\>' --or \
	-e '\<devm_ioremap_release\>' --or \
	-e '\<devm_memremap\>' --or \
	-e '\<devm_memunmap\>' --or \
	-e '\<__devm_memremap_pages\>' --or \
	-e '\<pci_remap_cfgspace\>' --or \
	-e '\<arch_has_dev_port\>' --or \
	-e '\<arch_phys_wc_add\>' --or \
	-e '\<arch_phys_wc_del\>' --or \
	-e '\<memremap\>' --or \
	-e '\<memunmap\>' --or \
	-e '\<arch_io_reserve_memtype_wc\>' --or \
	-e '\<arch_io_free_memtype_wc\>' --or \
	-e '\<__io_aw\>' --or \
	-e '\<__io_pbw\>' --or \
	-e '\<__io_paw\>' --or \
	-e '\<__io_pbr\>' --or \
	-e '\<__io_par\>' --or \
	-e '\<__raw_readb\>' --or \
	-e '\<__raw_readw\>' --or \
	-e '\<__raw_readl\>' --or \
	-e '\<__raw_readq\>' --or \
	-e '\<__raw_writeb\>' --or \
	-e '\<__raw_writew\>' --or \
	-e '\<__raw_writel\>' --or \
	-e '\<__raw_writeq\>' --or \
	-e '\<readb\>' --or \
	-e '\<readw\>' --or \
	-e '\<readl\>' --or \
	-e '\<readq\>' --or \
	-e '\<writeb\>' --or \
	-e '\<writew\>' --or \
	-e '\<writel\>' --or \
	-e '\<writeq\>' --or \
	-e '\<readb_relaxed\>' --or \
	-e '\<readw_relaxed\>' --or \
	-e '\<readl_relaxed\>' --or \
	-e '\<readq_relaxed\>' --or \
	-e '\<writeb_relaxed\>' --or \
	-e '\<writew_relaxed\>' --or \
	-e '\<writel_relaxed\>' --or \
	-e '\<writeq_relaxed\>' --or \
	-e '\<readsb\>' --or \
	-e '\<readsw\>' --or \
	-e '\<readsl\>' --or \
	-e '\<readsq\>' --or \
	-e '\<writesb\>' --or \
	-e '\<writesw\>' --or \
	-e '\<writesl\>' --or \
	-e '\<writesq\>' --or \
	-e '\<inb\>' --or \
	-e '\<inw\>' --or \
	-e '\<inl\>' --or \
	-e '\<outb\>' --or \
	-e '\<outw\>' --or \
	-e '\<outl\>' --or \
	-e '\<inb_p\>' --or \
	-e '\<inw_p\>' --or \
	-e '\<inl_p\>' --or \
	-e '\<outb_p\>' --or \
	-e '\<outw_p\>' --or \
	-e '\<outl_p\>' --or \
	-e '\<insb\>' --or \
	-e '\<insw\>' --or \
	-e '\<insl\>' --or \
	-e '\<outsb\>' --or \
	-e '\<outsw\>' --or \
	-e '\<outsl\>' --or \
	-e '\<insb_p\>' --or \
	-e '\<insw_p\>' --or \
	-e '\<insl_p\>' --or \
	-e '\<outsb_p\>' --or \
	-e '\<outsw_p\>' --or \
	-e '\<outsl_p\>' --or \
	-e '\<ioread8\>' --or \
	-e '\<ioread16\>' --or \
	-e '\<ioread32\>' --or \
	-e '\<ioread64\>' --or \
	-e '\<iowrite8\>' --or \
	-e '\<iowrite16\>' --or \
	-e '\<iowrite32\>' --or \
	-e '\<iowrite64\>' --or \
	-e '\<ioread16be\>' --or \
	-e '\<ioread32be\>' --or \
	-e '\<ioread64be\>' --or \
	-e '\<iowrite16be\>' --or \
	-e '\<iowrite32be\>' --or \
	-e '\<iowrite64be\>' --or \
	-e '\<ioread8_rep\>' --or \
	-e '\<ioread16_rep\>' --or \
	-e '\<ioread32_rep\>' --or \
	-e '\<ioread64_rep\>' --or \
	-e '\<iowrite8_rep\>' --or \
	-e '\<iowrite16_rep\>' --or \
	-e '\<iowrite32_rep\>' --or \
	-e '\<iowrite64_rep\>' --or \
	-e '\<__io_virt\>' --or \
	-e '\<pci_iounmap\>' --or \
	-e '\<virt_to_phys\>' --or \
	-e '\<phys_to_virt\>' --or \
	-e '\<ioremap_uc\>' --or \
	-e '\<ioremap\>' --or \
	-e '\<__ioremap\>' --or \
	-e '\<iounmap\>' --or \
	-e '\<ioremap\>' --or \
	-e '\<ioremap_nocache\>' --or \
	-e '\<ioremap_uc\>' --or \
	-e '\<ioremap_wc\>' --or \
	-e '\<ioremap_wc\>' --or \
	-e '\<ioremap_wt\>' --or \
	-e '\<ioport_map\>' --or \
	-e '\<ioport_unmap\>' --or \
	-e '\<ioport_map\>' --or \
	-e '\<ioport_unmap\>' --or \
	-e '\<xlate_dev_kmem_ptr\>' --or \
	-e '\<xlate_dev_mem_ptr\>' --or \
	-e '\<unxlate_dev_mem_ptr\>' --or \
	-e '\<virt_to_bus\>' --or \
	-e '\<bus_to_virt\>' --or \
	-e '\<memset_io\>' --or \
	-e '\<memcpy_fromio\>' --or \
	-e '\<memcpy_toio\>'

I also reordered a couple includes when they weren't alphabetical and
removed clk.h from kona, replacing it with clk-provider.h because
that driver doesn't use clk consumer APIs.
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: NMark Brown <broonie@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: NMax Filippov <jcmvbkbc@gmail.com>
Acked-by: NJohn Crispin <john@phrozen.org>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NStephen Boyd <sboyd@kernel.org>

dev_pm_domain_attach_by_name() can return NULL, so we should check for
that case when we're about to dereference gxpd.

Fixes: 9325d426 ("drm/msm/gpu: Attach to the GPU GX power domain")
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: NJordan Crouse <jcrouse@codeauorora.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190515170104.155525-1-sean@poorly.run

Remove dpu_kms.h which is included more than once
Signed-off-by: NSabyasachi Gupta <sabyasachi.linux@gmail.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/5cda6de6.1c69fb81.a3ae5.836a@mx.google.com

media_device_cleanup() and v4l2_m2m_unregister_media_controller() were
missing in the probe error path.
While at it, re-order calls in the remove path to unregister/cleanup
things in the reverse order they were initialized/registered.
Signed-off-by: NJonas Karlman <jonas@kwiboo.se>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

v4l2-compliance complains that ->bus_info is empty.
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

This makes the function more generic so it can easily be re-used when
adding support for the decoding functionality.
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Those calls are needed to restore a clean PM state when the probe fails
or when the driver is unloaded such that future ->probe() calls can
initialize runtime PM again.
Signed-off-by: NJonas Karlman <jonas@kwiboo.se>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Pass -1 to video_register_device() to let the core assign the first
free id instead of trying to get id 0.
In practice it doesn't make a difference since video_register_device()
is not strict about id requests and will anyway pick the first free id
starting at the id passed in argument, and passing -1 has the same
effect as passing 0. But let's comply with the API doc and pass -1
here.
Signed-off-by: NJonas Karlman <jonas@kwiboo.se>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The "param.count" value is a u64 thatcomes from the user.  The code
later in the function assumes that param.count is at least one and if
it's not then it leads to an Oops when we dereference the ZERO_SIZE_PTR.

Also the addition can have an integer overflow which would lead us to
allocate a smaller "pages" array than required.  I can't immediately
tell what the possible run times implications are, but it's safest to
prevent the overflow.

Link: http://lkml.kernel.org/r/20181218082129.GE32567@kadam
Fixes: 6db71994 ("drivers/virt: introduce Freescale hypervisor management driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Timur Tabi <timur@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

strndup_user() returns error pointers on error, and then in the error
handling we pass the error pointers to kfree().  It will cause an Oops.

Link: http://lkml.kernel.org/r/20181218082003.GD32567@kadam
Fixes: 6db71994 ("drivers/virt: introduce Freescale hypervisor management driver")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Timur Tabi <timur@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since commit dccd2304 ("ARM: 7430/1: sizes.h: move from asm-generic
to <linux/sizes.h>"), <asm/sizes.h> and <asm-generic/sizes.h> are just
wrappers of <linux/sizes.h>.

This commit replaces all <asm/sizes.h> and <asm-generic/sizes.h> to
prepare for the removal.

Link: http://lkml.kernel.org/r/1553267665-27228-1-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch implements the PPS ECHO functionality for pps-gpio, that
sysfs claims is available already.

Configuration is done via device tree bindings.

No changes are made to userspace interfaces.

This patch was originally written by Lukas Senger as part of a masters
thesis project and modified for inclusion into the linux kernel by Tom
Burkart.

Link: http://lkml.kernel.org/r/20190324043305.6627-4-tom@aussec.comSigned-off-by: NTom Burkart <tom@aussec.com>
Acked-by: NRodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NLukas Senger <lukas@fridolin.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch changes the GPIO access for the pps-gpio driver from the
integer based API to the descriptor based API.

The integer based API is considered deprecated and the descriptor based
API is the preferred way to access GPIOs as per
Documentation/driver-api/gpio/intro.rst

No changes are made to userspace interfaces.

Link: http://lkml.kernel.org/r/20190324043305.6627-2-tom@aussec.comSigned-off-by: NTom Burkart <tom@aussec.com>
Acked-by: NRodolfo Giometti <giometti@enneenne.com>
Reviewed-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Cc: Lukas Senger <lukas@fridolin.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When kernel panic happens, it will first print the panic call stack,
then the ending msg like:

[   35.743249] ---[ end Kernel panic - not syncing: Fatal exception
[   35.749975] ------------[ cut here ]------------

The above message are very useful for debugging.

But if system is configured to not reboot on panic, say the
"panic_timeout" parameter equals 0, it will likely print out many noisy
message like WARN() call stack for each and every CPU except the panic
one, messages like below:

	WARNING: CPU: 1 PID: 280 at kernel/sched/core.c:1198 set_task_cpu+0x183/0x190
	Call Trace:
	<IRQ>
	try_to_wake_up
	default_wake_function
	autoremove_wake_function
	__wake_up_common
	__wake_up_common_lock
	__wake_up
	wake_up_klogd_work_func
	irq_work_run_list
	irq_work_tick
	update_process_times
	tick_sched_timer
	__hrtimer_run_queues
	hrtimer_interrupt
	smp_apic_timer_interrupt
	apic_timer_interrupt

For people working in console mode, the screen will first show the panic
call stack, but immediately overridden by these noisy extra messages,
which makes debugging much more difficult, as the original context gets
lost on screen.

Also these noisy messages will confuse some users, as I have seen many bug
reporters posted the noisy message into bugzilla, instead of the real
panic call stack and context.

Adding a flag "suppress_printk" which gets set in panic() to avoid those
noisy messages, without changing current kernel behavior that both panic
blinking and sysrq magic key can work as is, suggested by Petr Mladek.

To verify this, make sure kernel is not configured to reboot on panic and
in console
 # echo c > /proc/sysrq-trigger
to see if console only prints out the panic call stack.

Link: http://lkml.kernel.org/r/1551430186-24169-1-git-send-email-feng.tang@intel.comSigned-off-by: NFeng Tang <feng.tang@intel.com>
Suggested-by: NPetr Mladek <pmladek@suse.com>
Reviewed-by: NPetr Mladek <pmladek@suse.com>
Acked-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In case create_workqueue fails, the fix releases resources and returns
-ENOMEM to avoid NULL pointer dereference.
Signed-off-by: NKangjie Lu <kjlu@umn.edu>
Acked-by: NAlexandre Bounine <alex.bou9@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The integer exponentiation is used in few places and might be used in
the future by other call sites.  Move it to wider use.

Link: http://lkml.kernel.org/r/20190323172531.80025-2-andriy.shevchenko@linux.intel.comSigned-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This prepares to move CONFIG_OPTIMIZE_INLINING from x86 to a common
place.  We need to eliminate potential issues beforehand.

Kbuild test robot has never reported -Wmaybe-uninitialized warning for
this probably because vf610_nfc_run() is inlined by the x86 compiler's
inlining heuristic.

If CONFIG_OPTIMIZE_INLINING is enabled for a different architecture and
vf610_nfc_run() is not inlined, the following warning is reported:

  drivers/mtd/nand/raw/vf610_nfc.c: In function `vf610_nfc_cmd':
  drivers/mtd/nand/raw/vf610_nfc.c:455:3: warning: `offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
     vf610_nfc_rd_from_sram(instr->ctx.data.buf.in + offset,
     ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
              nfc->regs + NFC_MAIN_AREA(0) + offset,
              ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
              trfr_sz, !nfc->data_access);
              ~~~~~~~~~~~~~~~~~~~~~~~~~~~

Link: http://lkml.kernel.org/r/20190423034959.13525-6-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kthread.h can't be included in psi_types.h because it creates a circular
inclusion with kthread.h eventually including psi_types.h and
complaining on kthread structures not being defined because they are
defined further in the kthread.h.  Resolve this by removing psi_types.h
inclusion from the headers included from kthread.h.

Link: http://lkml.kernel.org/r/20190319235619.260832-7-surenb@google.comSigned-off-by: NSuren Baghdasaryan <surenb@google.com>
Acked-by: NJohannes Weiner <hannes@cmpxchg.org>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following warning is seen on systems with broken clock divider.

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 1 Comm: swapper Not tainted 5.1.0-09698-g1fb3b526 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011be8>] (unwind_backtrace) from [<c000ebb8>] (show_stack+0x10/0x18)
[<c000ebb8>] (show_stack) from [<c07d3fd0>] (dump_stack+0x18/0x24)
[<c07d3fd0>] (dump_stack) from [<c0060d48>] (register_lock_class+0x674/0x6f8)
[<c0060d48>] (register_lock_class) from [<c005de2c>]
	(__lock_acquire+0x68/0x2128)
[<c005de2c>] (__lock_acquire) from [<c0060408>] (lock_acquire+0x110/0x21c)
[<c0060408>] (lock_acquire) from [<c07f755c>] (_raw_spin_lock+0x34/0x48)
[<c07f755c>] (_raw_spin_lock) from [<c0536c8c>]
	(pl111_display_enable+0xf8/0x5fc)
[<c0536c8c>] (pl111_display_enable) from [<c0502f54>]
	(drm_atomic_helper_commit_modeset_enables+0x1ec/0x244)

Since commit eedd6033 ("drm/pl111: Support variants with broken clock
divider"), the spinlock is not initialized if the clock divider is broken.
Initialize it earlier to fix the problem.

Fixes: eedd6033 ("drm/pl111: Support variants with broken clock divider")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1557758781-23586-1-git-send-email-linux@roeck-us.net

The endianness of data returned from the EC depends on the particular EC
version determined at run time. Cast from little/big endian explicitey
in the routine that flips endianness to the native one to make sparse
happy.
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Reported-by: Nkbuild test robot <lkp@intel.com>
Fixes: 76311b9a ("power: supply: olpc_battery: Add OLPC XO 1.75 support")
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.com>

msm_gem_describe() would attempt to dereference a NULL pointer via the
address space pointer when no IOMMU is present. Correct this by adding
the appropriate check.
Signed-off-by: NBrian Masney <masneyb@onstation.org>
Fixes: 575f0485 ("drm/msm: Clean up and enhance the output of the 'gem' debugfs node")
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190513234105.7531-2-masneyb@onstation.org