We know that 'ret' is not an error code because it has been tested a few
lines above.  So, if one of these function fails, 0 will be returned
instead of an error code.  Return -ENOMEM instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>

'ret' needs to be set with error code if hba_setup_cid_tbls fails.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change the copyright to:
Copyright © xxxx - 2016 Broadcom

Update email.ids:
@avagotech.com - @broadcom.com
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current EQ delay is set to 0 to receive very high max interrupt per sec.
Set EQ delay to 32 - reducing max interrupt rate from 65K to 20K per sec.

Set TCP connection window size to 64K with scale shift count 2.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In very rare scenario, connection gets killed after throwing this error:
scsi host0: BM_2312 : Event CXN_KILLED_BAD_WRB_INDEX_ERROR[15]... CID : 4
connection1:0: detected conn error (1011)

memset ISCSI_WRB descriptor to zero for all allocations of WRB handle.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

BUG: unable to handle kernel NULL pointer dereference at 000000000000015e
IP: [<ffffffffa0081700>]
hwi_get_async_handle.isra.23.constprop.39+0x90/0x1d0 [be2iscsi]
PGD 0
Oops: 0000 [#1] SMP
...
Call Trace:
 <IRQ>
 [<ffffffffa00818bc>] hwi_process_default_pdu_ring+0x7c/0x280 [be2iscsi]
 [<ffffffffa0088f51>] beiscsi_process_cq+0x321/0xb90 [be2iscsi]
 [<ffffffff810af028>] ? __wake_up_common+0x58/0x90
 [<ffffffff810b0d84>] ? __wake_up+0x44/0x50
 [<ffffffffa0089a2d>] be_iopoll+0x1d/0xb0 [be2iscsi]
 [<ffffffff812d1f61>] blk_iopoll_softirq+0xc1/0x100
 [<ffffffff81084b0f>] __do_softirq+0xef/0x280

The symptom observed is multiple async handles get queued for same index
thus causing leak in buffers posted to FW.

The root cause is:
- async handle is continued to be used even if it does not match the
completion.
- list_move operation done on already filled index.

1. Remove use of writables, host_write_ptr and ep_read_ptr.
2. Remove consumed logic to update writables. Instead, use only
free_entries to do the accounting of handles to be posted back.
3. Remove busy_list, instead use simple slot to index handles.
4. Added check no data, header less and overflow to make sure
all async_handles are flushed in error cases.
5. Added code to verify gathering of handles to form PDU by
checking final bit before forwarding PDU.
6. Added code to catch mismatch with CQE and handle gracefully.
7. Use AMAP, traverse cri_wait_queue list to post buffers, log
"async PDU" related errors.
8. Rearranged few data structures and added comments in init &
processing path.
9. Added WARN_ONs to catch any HD ring corruption.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver unload should call COMMON_FUNCTION_RESET. For TPE feature, this
ensures that FW has knowledge about driver getting unloaded and can
reset its bit vector.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Sessions are no longer valid, so schedule sess_work to fail the sessions
immediately when error is detected. This is done to avoid iSCSI transport
layer to keep sending NOP-Out which driver any ways fail.

Schedule sess_work immediately in case of HBA error. Old sessions are gone
for good and need to be re-established.

iscsi_session_failure needs process context hence this work.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After UE is detected, check for recoverable error by reading
SLIPORT SEMAPHORE register. If transient parity error i.e. 0xExxx
then schedule recovery work on driver wq.

FLag this error to prevent any transactions for the duration of ue2rp to
restart polling. After that, if FW becomes ready then recover port.

Wake up processes in wq before going offline.
Wait for process to execute before cleaning up.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mgmt_epfw_cleanup does not implement v1 of OPCODE_COMMON_ISCSI_CLEANUP
IOCTL for SkyHawk.

Replace use of MCCQ with BMBX for issuing the IOCTL.
Remove be_mcc_compl_poll which is no longer needed.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SLIPORT FUNCTION_RESET does not reset the chip.
So POST status needs to be checked before issuing FUNCTION_RESET.
The completion of FUNCTION_RESET is indicated in BMBX Rdy bit.

be_cmd_fw_initialize too needs to be done before issuing any cmd to FW.
be_cmd_fw_initialize is renamed as beiscsi_cmd_special_wrb.
Rearrange and rename few functions in init and cleanup path.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

beiscsi_fail_session is defined in be_cmds.c: move it to be_iscsi.c
Move card configuration commands to be_cmds.c.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

BE3 and SH cards can recover from transient parity errors treated
earlier as unrecoverable errors.

Add IOCTL to query FW support for this feature.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UE detection in health check is done in a work scheduled in global wq.
UE caused due to transient parity errors are recoverable and reported
within 1s. If this check for TPE gets delayed, PF0 might initiate
soft-reset and then status of UE recoverable is lost.

Handle UE detection in timer routine. Move out EQ delay update work
from health check. Make the IOCTL for EQ delay update non-blocking
as the completion status is ignored.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Boot work involves:
1. Find and fetch configured boot session and its handle.
2. Attempt to open the session if its not.
3. Get the session details for boot kset creation.
4. Logout of that session owned by FW.
5. Create boot kset for session details.

All these actions were done in blocking call with retries in global wq.
Other works in wq suffered if the IOCTLs stalled or timed out.

This change moves all the boot work to make it non-blocking.
The work queued in global wq just issues the IOCTL depending on the action
to be taken and mcc wq schedules work depending on status of the IOCTL.
Initial boot_work is started on link and ASYNC event.

The other code changes move all boot related functions in one place and
follow naming conventions.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Save ue_detected and fw_timeout errors in state field of beiscsi_hba.
BEISCSI_HBA_RUNNING
BEISCSI_HBA_LINK_UP
BEISCSI_HBA_BOOT_FOUND
BEISCSI_HBA_PCI_ERR
BEISCSI_HBA_FW_TIMEOUT
BEISCSI_HBA_IN_UE

Make sure no PCI transaction happens once in error state.
Add checks in IO path to detect HBA in error.

Skip hwi_purge_eq step which can't be done in error state.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

todo_mcc_cq is not needed as only MCC work is queued.
todo_cq is not used at all.
Rename functions to be consistent.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Redefine FW IP types.
Before issuing IOCTL to clear IP, check if IP is all zeroes.
All zeroes IP implies IP is not set in FW so FW fails that IOCTL.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename mgmt_get_if_info to be consistent with APIs name.
Rename create/destroy APIs to indicate IFACE operations.
Remove legacy be2iscsi and use beiscsi.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Move mgmt_get_all_if_id before any set param operation.
Rename mgmt_get_all_if_id to beiscsi_if_get_handle.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In beiscsi_setup_boot_info(), the boot_kset pointer should be set to
NULL in case of failure otherwise an invalid pointer dereference may
occur later.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMaurizio Lombardi <mlombard@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In beiscsi_setup_boot_info(), the boot_kset pointer should be set to
NULL in case of failure otherwise an invalid pointer dereference may
occur later.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMaurizio Lombardi <mlombard@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.

Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
 free_irq(irq, ...);
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This adds the missing error check and path for if the call to the
function hwi_init_controller fails as this error path was clearly missed
when writing beiscsi_eeh_resume and thus we must add it now in order to
be able to handle this nonrecoverable failing function call gracefully
in beiscsi_eeh_resume.
Signed-off-by: NNicholas Krause <xerofoify@gmail.com>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In case of error, the memory allocated for phwi_ctrlr was not freed.
Signed-off-by: NMaurizio Lombardi <mlombard@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

FW got into UE after running IO stress test

With kernel change to split session lock in frwd_lock and back_lock for
tx and rx path correspondingly, in the IO path, common resource used in
driver such as WRB was left unprotected.

Add wrb_lock spinlock to protect allocation and freeing of WRB.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Processing of mgmt and IO tasks are done in process context and
softirqs.

Allocation and freeing of sgl_handles needs to be done under
spin_lock_bh/spin_unlock_bh and move the locks to the routines.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Connection resets observed from some targets when NOP-Out with wrong
ExpStatSn is sent.

FW keeps track of StatSn and fills up ExpStatSn accordingly.  The header
filled up by the stack needs to be modified by driver to clear
ExpStatSn. If the field is not cleared, FW recalculates ExpStatSn and
wrong offset'ed ExpStatSn is seen in the wire trace.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

WARN_ON(atomic_read(&mccq->used) >= mccq->len) seen when FW gets into
UE.

MCCQ overflow is happening because driver discards any new request and
frees up the tag. The tag allocation controls the number of MCC WRB
posted.  It is being replenished but WRBs are not hence the WARN_ON.

Allocation and freeing of WRB and tags for MCC is now done in one place.
This helps to achieve proper accounting of WRB indices and MCC tags.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

beiscsi_mccq_compl -> beiscsi_mccq_compl_wait - indicate blocking call.
be_mcc_wait_compl -> be_mcc_compl_poll - indicate polling for completion.
be_mbox_db_ready_wait -> be_mbox_db_ready_poll - indicate polling for RDY.
be_mcc_compl_process -> beiscsi_process_mbox_compl - indicate BMBX compl.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

be_mcc_compl_process_isr is removed. MCC CQ processing is done only in
beiscsi_process_mcc_cq and MCC CQE processing is done only in
beiscsi_process_mcc_compl.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename mcc_numtag to mcc_tag_status.  MCC CQE status is processed using
macros already defined in be_cmds.h.

Add MCC_Q_WRB_ and MCC_Q_CMD_TAG_MASK macros to map to already defined
CQE_STATUS_ macros to be consistent when posting MCC.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mcc_cq_lock spin_lock is used only in beiscsi_process_mcc which is
called only when all interrupts are disabled from mgmt_epfw_cleanup
during unloading of driver. There is no other context where there can be
contention for the processing of CQ.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

hwi_write_buffer() does not check if mapping dma memory succeed. The
patch adds the check and failure handling.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Acked-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Login/Logout loop was hanging after few hours. /var/log/message showed
that alloc_wrb_handle() function was not able to allocate any new WRB.

Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not send nopout
Sep 11 11:25:22 Jhelum10 kernel: scsi host10: BM_4989 : Alloc of WRB_HANDLE
Failed for the CID : 384
Sep 11 11:25:22 Jhelum10 kernel: connection32513:0: Could not allocate pdu for
mgmt task.

Driver allocates WRB to pass login negotiated parameters information to FW
in beiscsi_offload_connection(). This allocated WRB was not freed so there
was WRB_Leak happening.

Put WRB used for posting the login-negotiated parameters back in pool.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

OS not responding when running 2 port traffic on 72 CPUs system.

be2iscsi IRQs gets affined to CPU0 when irqbalancer is disabled.
be_iopoll processing completions in BLOCK_IOPOLL_SOFTIRQ hogged CPU0.

1. Use budget to exit the polling loop. beiscsi_process_cq didn't honour
   it.
2. Rearming of EQ is done only after iopoll completes.

[mkp: Fixed up blk_iopoll -> irq_poll transition]
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

System crash in I+T card personality.

Fix to add validation for ULP in initiator mode, physical port number,
and supported queue, icd, cid counts.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Log messages for misconfigured transceivers reported by FW.

Register async events that driver handles using MCC_CREATE_EXT ioctl.
Errors messages for faulted/uncertified/unqualified optics are logged.
Added IOCTL to get port_name to be displayed in error message.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Null pointer dereference in shutdown path after taking dump.

Shutdown path is not needed as FW comes up clean every time during probe
after issuing FUNCTION reset MBOX command.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This is second part of actual fix for soft lockup.

All mbox cmds issued using BMBX and MCC are synchronized using mutex
mbox_lock instead of spin_lock. Used mutex_lock_interruptible where ever
possible.
Signed-off-by: NJitendra Bhivare <jitendra.bhivare@avagotech.com>
Reviewed-by: NShane Seymour <shane.seymour@hpe.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is no good reason to keep them apart, and this makes using the API
a bit simpler.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>