The driver can allow the user to configure whether the CRC aka the FCS
(Frame Check Sequence) is DMA'd to the host as part of the receive
buffer.  The driver usually wants this feature disabled so that the
hardware checks the FCS and strips it in order to save PCI bandwidth.

Control the reception of FCS to the host using the command:
ethtool -K eth0 rx-fcs <on|off>

The default shown in ethtool -k eth0 | grep fcs; should be "off", as the
hardware will drop any frame with a bad checksum, and DMA of the
checksum is useless overhead especially for small packets.

Testing Hints:
test the FCS/CRC arrives with received packets using
tcpdump -nnpi eth0 -xxxx
and it should show crc data as the last 4 bytes of the packet. Can also
use wireshark to turn on CRC checking and check the data is correct.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: NGrzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: NGrzegorz Nitka <grzegorz.nitka@intel.com>
Co-developed-by: NBenjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: NBenjamin Mikailenko <benjamin.mikailenko@intel.com>
Co-developed-by: NAnatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: NAnatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

In current implementation default VSI switch filter is only able to
forward traffic to a single VSI. This limits promiscuous mode with
private flag 'vf-true-promisc-support' to a single VF. Enabling it on
the second VF won't work. Also allmulticast support doesn't seem to be
properly implemented when vf-true-promisc-support is true.

Use standard ice_add_rule_internal() function that already implements
forwarding to multiple VSI's instead of constructing AQ call manually.

Add switch filter for allmulticast mode when vf-true-promisc-support is
enabled. The same filter is added regardless of the flag - it doesn't
matter for this case.

Remove unnecessary fields in switch structure. From now on book keeping
will be done by ice_add_rule_internal().

Refactor unnecessarily passed function arguments.

To test:
1) Create 2 VM's, and two VF's. Attach VF's to VM's.
2) Enable promiscuous mode on both of them and check if
   traffic is seen on both of them.
Signed-off-by: NMichal Wilczynski <michal.wilczynski@intel.com>
Tested-by: NMarek Szlosek <marek.szlosek@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.

This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.

We plan on refactoring VF storage in a few key ways:

  1) converting from a simple static array to a hash table
  2) using krefs to track VF references obtained from the hash table
  3) use RCU to delay release of VF memory until after all references
     are dropped

This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.

With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.

We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.

For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKonrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The status of support for RDMA is currently being tracked with two
separate status flags. This is unnecessary with the current state of
the driver.

Simplify status tracking down to a single flag.

Rename the helper function to denote the RDMA specific status and
universally use the helper function to test the status bit.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NLeszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new outer_vlan_ops member to the ice_vsi structure as outer VLAN
ops are only available when the device is in Double VLAN Mode (DVM).
Depending on the VSI type, the requirements for what operations to
use/allow differ.

By default all VSI's have unsupported inner and outer VSI VLAN ops. This
implementation was chosen to prevent unexpected crashes due to null
pointer dereferences. Instead, if a VSI calls an unsupported op, it will
just return -EOPNOTSUPP.

Add implementations to support modifying outer VLAN fields for VSI
context. This includes the ability to modify VLAN stripping, insertion,
and the port VLAN based on the outer VLAN handling fields of the VSI
context.

These functions should only ever be used if DVM is enabled because that
means the firmware supports the outer VLAN fields in the VSI context. If
the device is in DVM, then always use the outer_vlan_ops, else use the
vlan_ops since the device is in Single VLAN Mode (SVM).

Also, move adding the untagged VLAN 0 filter from ice_vsi_setup() to
ice_vsi_vlan_setup() as the latter function is specific to the PF and
all other VSI types that need an untagged VLAN 0 filter already do this
in their specific flows. Without this change, Flow Director is failing
to initialize because it does not implement any VSI VLAN ops.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

There are multiple places where VLAN 0 is being added. Create a function
to be called in order to minimize changes as the implementation is expanded
to support double VLAN and avoid duplicated code.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>

Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>

To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>

Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NTony Brelinski <tony.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.

Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
	queues 4@0 4@4 4@8  hw 1 mode channel

Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.

User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.

Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
	num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
	shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
	max_rate 4Gbit 5Gbit 6Gbit 7Gbit

Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>

Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NBharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NBharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.

In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.

This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).

The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.

Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NKonrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.

Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.

Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.

Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.

Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.

Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Expose SMA and U.FL connectors as ptp_pins on E810-T based adapters and
allow controlling them.

E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL
- 1 internal RX U.FL

U.FL connectors share signal lines with the SMA connectors. The TX U.FL1
share the line with the SMA1 and the RX U.FL2 share line with the SMA2.
This dependence is controlled by the ice_verify_pin_e810t.

Additionally add support for the E810-T-based  devices which don't use the
SMA/U.FL controller. If the IO expander is not detected don't expose pins
and use 2 predefined 1PPS input and output pins.
Signed-off-by: NMaciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: NSunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Implement functions to make setting VSI security config easier.
Main function ice_update_security fills security section field and
checks against error in updating VSI. Reset functions are responsible
for correct filling config according to user expectations.

This helper is needed because destination override is located in
this section. Driver has to set this bit to allow strering Tx packet
on VSI based on value in Tx descriptors.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: NSandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

DSCP a.k.a L3 QoS is only supported on certain devices. To enforce this,
this patch introduces a bitmap of features and helper functions.

The feature bitmap is set based on device IDs on driver init. Currently,
DSCP is the only feature in this bitmap, but there will be more in the
future. In the DCB netlink flow, check if the feature bit is set before
exercising DSCP.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NGurucharan G <gurucharanx.g@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.

Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.

The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.

If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is

  PHC - (lower_32_bits(PHC) - timestamp)

If the Rx timestamp was captured after the PHC time, then the real
timestamp is

  PHC + (timestamp - lower_32_bits(PHC))

These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.

In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.

Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.

Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.

To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.

Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.

With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:

This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".

This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.

To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.

Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Currently, when a VF requests queue configuration via
VIRTCHNL_OP_CONFIG_VSI_QUEUES the PF driver expects that this message
will only be called once and we always assume the queues being
configured start from 0. This is incorrect and is causing issues when
a VF tries to send this message for multiple queue blocks. Fix this by
using the queue_id specified in the virtchnl message and allowing for
individual Rx and/or Tx queues to be configured.

Also, reduce the duplicated for loops for configuring the queues by
moving all the logic into a single for loop.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NKonrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them.  This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.

In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.

While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The ice_setup_pf_sw function can cause a memory leak if register_netdev
fails, due to accidentally failing to free the VSI rings. Fix the memory
leak by using ice_vsi_release, ensuring we actually go through the full
teardown process.

This should be safe even if the netdevice is not registered because we
will have set the netdev pointer to NULL, ensuring ice_vsi_release won't
call unregister_netdev.

An alternative fix would be moving management of the PF VSI netdev into
the main VSI setup code. This is complicated and likely requires
significant refactor in how we manage VSIs

Fixes: 3a858ba3 ("ice: Add support for VSI allocation and deallocation")
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Always clear the previous value in QRXFLXP_CNTXT before writing a new
value. This will make it so re-used queues will not accidentally take the
previously configured settings.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.

Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move filter functions to separate file.

Add functions that prepare suitable ice_fltr_info struct
depending on the filter type and add this struct to earlier created
list:
- ice_fltr_add_mac_to_list
- ice_fltr_add_vlan_to_list
- ice_fltr_add_eth_to_list
This functions are used in adding and removing filters.

Create wrappers for functions mentioned above that alloc list,
add suitable ice_fltr_info to it and call add or remove function.
- ice_fltr_prepare_mac
- ice_fltr_prepare_mac_and_broadcast
- ice_fltr_prepare_vlan
- ice_fltr_prepare_eth
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable name 'type' is not very descriptive. Replace instances of
those with a variable name that is more descriptive or replace it if not
needed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.

1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.

In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.

Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.

This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.

Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Allow support for S-Tag + C-Tag VLAN traffic by disabling pruning when
there are no 0x8100 VLAN interfaces currently created on top of the PF.
When an 0x8100 VLAN interface is configured, enable pruning and only
support single and double C-Tag VLAN traffic. If all of the 0x8100
interfaces that were created on top of the PF are removed via
ethtool -K <iface> rx-vlan-filter off or via ip tools, then disable
pruning and allow S-Tag + C-Tag traffic again.

Add VLAN 0 filter by default for the PF. This is because a bridge
sets the default_pvid to 1, sends the request down to
ice_vlan_rx_add_vid(), and we never get the request to add VLAN 0 via
the 8021q module which causes all untagged traffic to be dropped.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool.  Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe.  This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:

ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.

ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.

ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule

ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.

Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively.  Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.

Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>