After a shutdown reset, the LAA needs to be restored before posting the
post-reset signature in shared memory.  If the LAA is not restored
before then, the bootcode will assume the factory default MAC address
and WOL will not work with the LAA.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch restricts the CLKREQ bugfix to the A0 and A1 revisions
of 57780 ASIC rev chips.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5761 WOL and LED fixes used the PCI device ID to as the activation
key.  The 5761S requires the same process.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On rare occasions, send BD corruptions can occur.  This patch
fixes the problem by increasing the L1 entry threshold to 4
milliseconds.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some 57780 ASIC revision parts do not have NVRAM.  Code the driver so
that it is tolerant of this configuration.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver's ISR is coded to accept interrupts as its own if the
status block tag does not equal the last tag the driver has seen.  The
last_tag field is updated from tg3_poll.  In a screaming interrupt
situation from another device sharing tg3's IRQ, tg3_poll does not get
a chance to be called, so the last_tag will always be out of sync with
the status block tag.  Consequently, the driver will continually
declare the screaming interrupts as its own, thus thwarting the
screaming interrupt detection logic.

This patch solves the problem by creating a new last_irq_tag member and
recording the status block tag in the ISR.  The ISR then checks the
last_irq_tag for interrupt ownership.

Many thanks to John Marvin for the detailed bug report and analysis and
Michael Chan for the bugfix.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Tested-by: NJohn Marvin <jsm@fc.hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	net/core/dev.c

The recent NVRAM patches sanitized how the driver deals with NVRAM
data, but they failed to bring the SEEPROM interfaces inline with
the new strategy.  This patch brings the SEEPROM interfaces up to date.
This patch also reverts commit 0d489ffb
("tg3: fix big endian MAC address collection failure").
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Tested-by: NRobin Holt <holt@sgi.com>
Tested-by: NJames Bottomley <james.bottomley@HansenPartnership.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"mac80211: fix basic rates setting from association response"
introduced a copy/paste error.

Unfortunately, this not just leads to wrong data being passed
to the driver but is remotely exploitable for some hardware or
driver combinations.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently beacon loss detection triggers after a scan. A probe request
is sent and a message like this is printed to the log:

wlan0: beacon loss from AP 00:12:17:e7:98:de - sending probe request

But in fact there is no beacon loss, the beacons are just not received
because of the ongoing scan. Fix it by updating last_beacon after
the scan has finished.
Reported-by: NJaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.

However, the device does not accept the firmware on resume.
and it will exit with:

> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove this unused Kconfig variable, which Intel apparently once
promised to make use of but never did.
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch deactivates powersave in station mode.

It does not work correctly yet, so the code does more harm than good.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"not" is not printed without a space after %pM
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As the sk_sleep wait queue actually lives in tfile, which may be
detached from the tun device, bad things will happen when we use
sk_sleep after detaching.

Since the tun device is the persistent data structure here (when
requested by the user), it makes much more sense to have the wait
queue live there.  There is no reason to have it in tfile at all
since the only time we can wait is if we have a tun attached.
In fact we already have a wait queue in tun_struct, so we might
as well use it.
Reported-by: NEric W. Biederman <ebiederm@xmission.com>
Tested-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Tested-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit c70f1829 ("tun: Fix
races between tun_net_close and free_netdev") fixed a race where
an asynchronous deletion of a tun device can hose a poll(2) on
a tun fd attached to that device.

However, this came at the cost of moving the tun wait queue into
the tun file data structure.  The problem with this is that it
imposes restrictions on when and where the tun device can access
the wait queue since the tun file may change at any time due to
detaching and reattaching.

In particular, now that we need to use the wait queue on the
receive path it becomes difficult to properly synchronise this
with the detachment of the tun device.

This patch solves the original race in a different way.  Since
the race is only because the underlying memory gets freed, we
can prevent it simply by ensuring that we don't do that until
all tun descriptors ever attached to the device (even if they
have since be detached because they may still be sitting in poll)
have been closed.

This is done by using reference counting the attached tun file
descriptors.  The refcount in tun->sk has been reappropriated
for this purpose since it was already being used for that, albeit
from the opposite angle.

Note that we no longer zero tfile->tun since tun_get will return
NULL anyway after the refcount on tfile hits zero.  Instead it
represents whether this device has ever been attached to a device.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

last_synq_overflow eats 4 or 8 bytes in struct tcp_sock, even
though it is only used when a listening sockets syn queue
is full.

We can (ab)use rx_opt.ts_recent_stamp to store the same information;
it is not used otherwise as long as a socket is in listen state.

Move linger2 around to avoid splitting struct mtu_probe
across cacheline boundary on 32 bit arches.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can in some situations drop packets in netif_rx()

loopback driver does not report these (unlikely) drops to its stats,
and incorrectly change packets/bytes counts.

After this patch applied, "ifconfig lo" can reports these drops as in :

# ifconfig lo
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:692562900 errors:3228 dropped:3228 overruns:0 frame:0
          TX packets:692562900 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:2865674174 (2.6 GiB)  TX bytes:2865674174 (2.6 GiB)

I initialy chose to reflect those errors only in tx_dropped/tx_errors, but David
convinced me that it was really RX errors, as loopback_xmit() really starts
a RX process. (calling eth_type_trans() for example, that itself pulls the ethernet header)

These errors are accounted in rx_dropped/rx_errors.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This loop over fragments in napi_fraginfo_skb() was "interesting".
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just noticed while doing some new work that the recent
mid-wq adjustment logic will misbehave when FACK is not
in use (happens either due sysctl'ed off or auto-detected
reordering) because I forgot the relevant TCPCB tagbit.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alex Sidorenko reported:

"while experimenting with 'netem' we have found some strange behaviour. It
seemed that ingress delay as measured by 'ping' command shows up on some
hosts but not on others.

After some investigation I have found that the problem is that skbuff->tstamp
field value depends on whether there are any packet sniffers enabled. That
is:

- if any ptype_all handler is registered, the tstamp field is as expected
- if there are no ptype_all handlers, the tstamp field does not show the delay"

This patch prevents unnecessary update of tstamp in dev_queue_xmit_nit()
on ingress path (with act_mirred) adding a check, so minimal overhead on
the fast path, but only when sniffers etc. are active.

Since netem at ingress seems to logically emulate a network before a host,
tstamp is zeroed to trigger the update and pretend delays are from the
outside.
Reported-by: NAlex Sidorenko <alexandre.sidorenko@hp.com>
Tested-by: NAlex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This has been broken for a while. I happened to catch it testing because one
app "knew" that the top line of the calls data was the policy line and got
confused.

Put the header back.
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Release vectors when a MSI-X allocation fails.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.

The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.

Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded.

This apparently confused *some* versions of networkmanager.

Andy tested this for e1000e and confirmed it was working for him.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: NAndrew Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.

Andy tested this for e1000e and confirmed it was working for him.

see thread: http://marc.info/?l=linux-netdev&m=123946479705636&w=2Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndy Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: NAndrew Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.

in addition this driver appeared to need a netif_start_queue at
the end of open.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: NAndrew Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Andrew Lutomirski <amluto@gmail.com>

All the intel wired ethernet drivers were calling netif_carrier_off
and netif_stop_queue (or variants) before calling register_netdevice

This is incorrect behavior as was pointed out by davem, and causes
ifconfig and friends to report a strange state before first link
after the driver was loaded, since without a netif_carrier_off, the stack
assumes carrier_on, but before register_netdev, netlink messages are not
sent out telling link state.

This apparently confused *some* versions of networkmanager.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reported-by: NAndrew Lutomirski <amluto@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom chips with 2.1 firmware handle the fallback case to a SCO
link wrongly when setting up eSCO connections.

  < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
      handle 11 voice setting 0x0060
  > HCI Event: Command Status (0x0f) plen 4
      Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
  > HCI Event: Connect Complete (0x03) plen 11
      status 0x00 handle 1 bdaddr 00:1E:3A:xx:xx:xx type SCO encrypt 0x01

The Link Manager negotiates the fallback to SCO, but then sends out
a Connect Complete event. This is wrong and the Link Manager should
actually send a Synchronous Connection Complete event if the Setup
Synchronous Connection has been used. Only the remote side is allowed
to use Connect Complete to indicate the missing support for eSCO in
the host stack.

This patch adds a workaround for this which clearly should not be
needed, but reality is that broken Broadcom devices are deployed.

Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: NMarcel Holtman <marcel@holtmann.org>

Some Bluetooth chips (like the ones from Texas Instruments) don't do
proper eSCO negotiations inside the Link Manager. They just return an
error code and in case of the Kyocera ED-8800 headset it is just a
random error.

  < HCI Command: Setup Synchronous Connection 0x01|0x0028) plen 17
    handle 1 voice setting 0x0060
  > HCI Event: Command Status (0x0f) plen 4
    Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
  > HCI Event: Synchronous Connect Complete (0x2c) plen 17
    status 0x1f handle 257 bdaddr 00:14:0A:xx:xx:xx type eSCO
    Error: Unspecified Error

In these cases it is up to the host stack to fallback to a SCO setup
and so retry with SCO parameters.

Based on a report by Nick Pelly <npelly@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>