This makes gpio.c fully independent of pxa-regs.h (except for the
virtual address of the registers).
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Looks like we have to live with pxa_gpio_mode() for a while, giving
its presence is actually making gpio.c not generic enough, let's
move it temporarily outside before it can be fully purged.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This is part of the work making gpio.c generic enough, the changes
include:

1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)

2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
   number for the muxed GPIOs

3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
   and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: NEric Miao <eric.miao@marvell.com>

1. Driver code where pxa_request_dma() is called will most likely
   reference DMA registers as well,  and it is really unnecessary
   to include pxa-regs.h just for this. Move the definitions into
   <mach/dma.h> and make relevant drivers include it instead of
   <mach/pxa-regs.h>.

2. Introduce DMAC_REGS_VIRT as the virtual address base for these
   DMA registers. This allows later processors to re-use the same
   IP while registers may start at different I/O address.
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:

  <mach/pxa25x.h>  - for pxa25x based platforms
  <mach/pxa27x.h>  - for pxa27x based platforms
  <mach/pxa300.h>  - for pxa300 based platforms
  <mach/pxa320.h>  - for pxa320 based platforms
  <mach/pxa930.h>  - for pxa930 based platforms

NOTE:

1. one header one board file, they are not compatible (i.e. they have
   conflicting definitions which won't compile if included together).

2. Unless strictly necessary, the following header files are considered
   to be SoC files use _only_, and is not recommended to be included in
   board code:

    <mach/hardware.h>
    <mach/pxa-regs.h>
    <mach/pxa2xx-regs.h>
    <mach/pxa3xx-regs.h>
    <mach/mfp.h>
    <mach/mfp-pxa2xx.h>
    <mach/mfp-pxa25x.h>
    <mach/mfp-pxa27x.h>
    <mach/mfp-pxa3xx.h>
    <mach/mfp-pxa300.h>
    <mach/mfp-pxa320.h>
    <mach/mfp-pxa930.h>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Default to the same behaviour as the shipped WinCE system.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

so they can be shared with gpio_vbus.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Fixes an off-by-one error.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Add m2p dma support to the ep93xx
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add the clocks for ep93xx m2p dma engine.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

SCALE: add ice dcc support

Tested on the ixp425 with the ice PEEDI
Ack-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conflicts:

	arch/arm/plat-mxc/dma-mx1-mx2.c

We should not be modifying the scatterlist passed to us from the
driver code; doing so breaks assumptions made by the DMA API code,
and could cause problems if the driver retries a transfer using an
old scatterlist.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no point these being in a generic include file when they're
only used in arch/arm/mach-rpc/dma.c.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Code has never been in buildable state since initial
merge.
Signed-off-by: NDmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the unneeded #include <mach/hardware.h>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the platform_device and resource structures for the USB
ISP1761 chip, usable with the in-kernel isp1760 driver.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This driver adds the platform_device definitions to allow the use of
CompactFlash on the RealView PB11MPCore and PB-A8 platforms. Note that
the CompactFlash controller is expected to be initialised by the Boot
Monitor and support the True IDE mode.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This chip is on the I2C bus on the RealView and Versatile boards. The
patch adds the i2c_board_info definition for this device and registers
it with the I2C subsystem.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If dev->id is not -1, the platform code may use static bus numbering
rather than dynamic. The patch also changes the i2c_versatile_init to a
subsys_initcall rather than module_init to make sure it is initialised
before the I2C devices initialisation.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This includes a new defconfig for the Shark and some changes to
the mach-shark directory to avoid namespace pollution and to
switch the rtc to the newer driver.
Signed-off-by: NAlexander Schulz <alex@shark-linux.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure that the LCD engine is correctly re-initialised
and the correct parameters passed ot s3c2410fb_init_registers.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Ensure __iomem attribute is __force 'd off in the minimal
__raw_writel() implementation.
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch also makes the frame pointer default to y only if
!ARM_UNWIND. LOCKDEP no longer selects FRAME_POINTER if ARM_UNWIND is
enabled.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is needed to allow or stop the unwinding at certain points in the
kernel like exception entries.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ELF section parsing for the unwinding tables in loadable
modules together with the PREL31 relocation symbol resolving.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds the main functionality for parsing the stack unwinding
information generated by the ARM EABI toolchains. The unwinding
information consists of an index with a pair of words per function and a
table with unwinding instructions. For more information, see "Exception
Handling ABI for the ARM Architecture" at:

http://infocenter.arm.com/help/topic/com.arm.doc.subset.swdev.abi/index.htmlSigned-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch changes the walk_stacktrace and its callers for easier
integration of stack unwinding. The arch/arm/kernel/stacktrace.h file is
also moved to arch/arm/include/asm/stacktrace.h.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch moves code around in the arch/arm/kernel/traps.c file for
easier integration of the stack unwinding support.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add W90P910 Evaluate Board NOR flash driver support,
The EV Board default support W19B320ABT7H of Winbond inc.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Delete the macros W90X900_RES and W90X900_DEVICE
I thought it will be better to define the structures
for each device directly.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The __cpu_up() function in arch/arm/kernel/smp.c sets the pmd entries
without flushing or cleaning them.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The VFPv3D16 is a VFPv3 CPU configuration where only 16 double registers
are present, as the VFPv2 configuration. This patch adds the
corresponding hwcap bits so that applications or debuggers have more
information about the supported features.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>