The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.

So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.

Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

HS400 timing values are added for SMDK5420, exynos5420-peach-pit
and exynos5800-peach-pi boards. This also adds RCLK GPIO line,
this gpio should be in pull-down state.
This also enables HS400 on peach-pi and this updates the clock
frequency to 800MHz to be set as input clock to controller.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
[alim.akhtar@samsung.com: addressed review comments]
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.

This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: NTushar Behera <tushar.b@samsung.com>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.

Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.

Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:

* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]

The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.

But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.

It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.

Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Tested-by: NRahul Sharma <rahul.sharma@samsung.com>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.

To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have both
a power and lid GPIO keys but only the former was defined in the
DTS. Add DTS snippets for the lid GPIO key too. These were taken
from the downstream ChromeOS 3.8 kernel tree.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NKukjin Kim <kgene@kernel.org>

MMC capability for HS200 is parsed in mmc/core/host.c as
dts string "mmc-hs200-1_8v".

This patch corrects the dts string for Exynos5420 based peach-pit
and Exynos5800 based peach-pi boards.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Peach Pit and Pi machines, the
Maxim 77802 32kHz AP clock is used as the source clock.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: NAndreas Faerber <afaerber@suse.de>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add DT nodes for ps8622 bridge chip and panel.
Add backlight power supply for pwm-backlight.
Also add bridge phandle needed by dp to enable display on peach_pit.
Signed-off-by: NAjay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Peach Pit board has an Atmel maXTouch trackpad device.
Add the needed Device Tree nodes to support it.

This Device Tree change is based on the Chrome OS 3.8 tree
but adapted to use the mainline Atmel maXTouch DT binding.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The downstream ChromeOS 3.8 kernel sets the clock frequency
for the I2C bus 7 at 400kHz. Do the same change in mainline.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The Exynos5420 based Peach Pit and the Exynos5800 based Peach Pi
machines have an i2c ISL29018 light sensor. This patch adds the
device nodes needed to support this device.

These DTS snippets were taken from the downstream Chrome OS 3.8
kernel Device Tree for Peach Pit and Pi boards.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch creates a thermistor fragment carrying the NTC
Thermistor nodes as children of the IIO based ADC.

This fragment is included in exynos5420-peach-pit.dts and
exynos5800-peach-pi.dts.
Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adding regulators for hdmi for peach-pit board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Exynos5420 based Peach Pit and Exynos5800 based Peach Pi boards
uses a Maxim 77802 power management IC to drive regulators and
its Real Time Clock. This patch adds support for this chip.

These are the device nodes and pinctrl configuration that
are present on the Peach pit DeviceTree source file in the
the Chrome OS kernel 3.8 tree.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The DeviceTree files for the Peach Pit and Pi machines have
a simplistic model of the connections between the different
regulators since not all the tps65090 regulators get their
input supply voltage from the VDC. DCDC1-3, LD0-1 and fet7
parent supply is indded VDC but the fet1-6 get their input
supply from the DCDC1 and DCDC2 output voltage rails.

Update the DeviceTree to better reflect the real connections
between tps65090 regulators. Having this information in the
DTS is useful since FETs are switches that don't provide an
output voltage so the regulator core needs to fetch the FET
parent output voltage if the child voltage is queried.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

dw-mmc controller can support multiple slots.
But, there are no use-cases anywhere. So we don't need to support the
slot-node for dw-mmc controller.
And "supports-highspeed" property in dw-mmc is deprecated.
"supports-highspeed" property can be replaced with "cap-sd/mmc-highspeed".
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NTushar Behera <trblinux@gmail.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NSachin Kamat <sachin.kamat@samsung.com>
[kgene.kim@samsung.com: rebased exynos5250-snow changes]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This adds cros_ec to exynos5420-peach-pit and exynos5800-peach-pi,
including:
* The keyboard
* The i2c tunnel
* The tps65090 under the i2c tunnel
* The battery under the i2c tunnel

To add extra motivation, it should be noted that tps65090 is one of
the things needed to get display-related FETs turned on for pit and
pi.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NTushar Behera <tushar.b@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake.  If we don't set it to anything then
the TPM will be reset.  U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything.  It will get pulled back high again during a
normal warm reset when it will default back to an input.

To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NVikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add sound-card name property to Snow/Peach-Pit/Peach-Pi boards.
Signed-off-by: NTushar Behera <tushar.b@samsung.com>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Peach-pit and Peach-pi boards are almost similar, hence the DTS file
is also very similar. Sorting nodes in both these files will allow
us to figure out the difference easily.

All the node aliases are sorted in alphabetically increasing order.
There is no functional change with this patch.
Signed-off-by: NTushar Behera <tushar.b@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

DP Hpd Gpio pin which is "gpx2-6" in Exynos 5420 based peach board,
belongs to Pinctrl_0. It has moved to pinctrl_0 from pinctrl_3.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable dp-controller for peach-pit board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable fimd for peach-pit board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The audio setup on Peach-pit board is similar to Snow board, hence the
sound-card driver used on Snow board can be reused on Peach-pit board.

Peach-pit board uses MAX98090 audio codec.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Enable hdmi for exynos5420 based peach-pit board.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>