Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.

Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a switch is connected as a PHY to the MAC driven by tg3, use
phylib and provide the phy address to tg3 from the sprom.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When phylib was in use tg3 only searched at address 01 on the mdio
bus and did not work with any other address. On the BCM4705 SoCs the
switch is connected as a PHY behind the MAC driven by tg3 and it is at
PHY address 30 in most cases. This is a preparation patch to allow
support for such switches.

phy_addr is set to TG3_PHY_MII_ADDR for all devices, which are using
phylib, so this should not change any behavior.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x makes a dangerous use of skb_is_gso_v6().

It should first make sure skb is a gso packet
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.

When multi queue support will be added some changes to Byte Queue
handling is needed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use common code for getting the pcie link speed/width for debug printing.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new LED mode for the BCM848xx to support new board type.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change bnx2x_bsc_read function prototype (more of a cosmetic change).
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current bnx2x implementation controls the number of VFs only by
standard sysfs support, and will reject setting the number of VFs
when the PF is not loaded.
As a result, there is no need to schedule a delayed work to enable
SR-IOV when PF is loaded, as the number of VFs at that point
must be 0.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running ethtool on VF interfaces, returning values should indicate
that the interface does not support self-test or register dump.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3fb43eb2 ("bnx2x: Change to D3hot only on removal") nvram
is accessible whenever the driver is loaded - Thus it is possible to
test it during self-test even if the interface is down
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a mix of function prototypes with and without extern
in the kernel sources.  Standardize on not using extern for
function prototypes.

Function prototypes don't need to be written with extern.
extern is assumed by the compiler.  Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).

Wait until firmware ack is written before unlocking channel
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.

This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.

Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spinlock is not needed after conversion of tg3_flags from array to
set_bit().
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Distinguish between tx, rx and txrx interrupts.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the 5717, 5719, 5720 and 5762 devices, in shared link/activity mode,
the blink rate must be overridden with all bits set.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for 57764, 57765, 57787, 57782 and 57786
devices.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency with other register access functions, add shadow
register access function of the type (register/val).
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Local symbols used only in this file are made static.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Ariel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 104a43ed
    cnic: Use CHIP_NUM macros from bnx2x.h

changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not.  There is another place in cnic that is still using
the old method to determine if FCoE is supported or not.  The 2 methods
may not yield the same result after the network interface is brought down
and up.  This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.

The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro.  As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit b9871bcf
    bnx2x: VF RSS support - PF side

changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc.  For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset.  This saves the driver from
having to keep track of an extra variable.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset.  This saves the driver from
having to keep track of an extra variable.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>