Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.

Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Anirban was seeing netfront received MTU size packets, which downgraded
throughput. The following patch makes netfront use GRO API which
improves throughput for that case.
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: Anirban Chakraborty <abchak@juniper.net>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: NKonrad Wilk <konrad.wilk@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a switch is connected as a PHY to the MAC driven by tg3, use
phylib and provide the phy address to tg3 from the sprom.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When phylib was in use tg3 only searched at address 01 on the mdio
bus and did not work with any other address. On the BCM4705 SoCs the
switch is connected as a PHY behind the MAC driven by tg3 and it is at
PHY address 30 in most cases. This is a preparation patch to allow
support for such switches.

phy_addr is set to TG3_PHY_MII_ADDR for all devices, which are using
phylib, so this should not change any behavior.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ethtool callbacks necessary to configure the
number of RSS queues.

The maximum number of queues is in accordance with the datasheets.
Signed-off-by: NLaura Mihaela Vasilescu <laura.vasilescu@rosedu.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the ethtool offline tests for i354 devices.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch renames the LL_EXTENDED_STATS and some of the functions required to
implement busy polling in the ixgbe driver, in order to remove the marketing
"low latency" blurb which hides what the code actually does.

This furthers work which was requested by Linus Torvalds when the initial busy
poll code was included in the kernel. The code in the ixgbe driver itself was
never properly renamed to reflect the change to busy polling as the title.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleans up the whitespace issues noticed during code review where
a mix of tabs and spaces were used for indentation.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added support for DCB registers dump using ethtool -d option both for
82599 and x540 ethernet controllers
Signed-off-by: NLeonardo Potenza <leonardo.potenza@intel.com>
Signed-off-by: NMaryam Tahhan <maryam.tahhan@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After this patch the API negotiation will occur in the reset path.  So now
the PF will be informed of the API version earlier.  This will also require
the mailbox lock to be initialize sooner as well.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New function was added to wait for Rx queues to be disabled before
disabling NAPI. This function also allows us to  modify
ixgbevf_rx_desc_queue_enable() to better match ixgbe.  I also cleaned up
some msleep calls to usleep_range while I was in this code anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we are already checking for read failure in check_link we don't need
to do it here. Instead just make sure the watchdog task gets scheduled, if
we are up, and it can be done there. This will better follow igbvf method
of handling a mailbox event and message timeout.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the use of hw_dbg in ixgbevf when the ixgbe_get_regs function
is called from ethtool. This goes along side a patch to ethtool which enables
proper support for ixgbevf pretty-printing of registers.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the xmit path, the driver may drop some pkts due to reasons such as
DMA mapping errors, out of memory conditions or to protect HW from
unrecoverable errors. Add a counter in TX-stats for such drops.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current EQ delay calculation for AIC is based only on RX packet rate.
This fails to be effective when there's only TX and no RX.
This patch inclues:
- Calculating EQ-delay based on both RX and TX pps.
- Modifying EQ-delay of all EQs via one cmd, instead of issuing a separate
  cmd for each EQ.
- A new structure to store interrupt coalescing parameters, in a separate
  cache-line from the EQ-obj.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cmd needs to be sent to FW when enabling VFs (currently used only
for Lancer.) Also, avoid calling the cmd when driver loads and finds that
VFs are already enabled from a previous load.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BE3-R 1G ports (identified by port numbers 2 and 3) the FW cannot properly
support multiple TXQs. This also makes the number of RX and TX queues symmetric
as only a single RXQ is available on 1G ports.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a required field for all TX_CREATE cmd versions > 0.
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-define the sriov_want() macro to check for number of VFs that need
to be enabled in the current load of the driver or the number of VFs that
still remain enabled from the previous load (attached VFs cannot be disabled.)
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Interface needs to be brought down and up while configuring SR-IOV.
  Protect interface up/down using rtnl_lock()/rtnl_unlock()
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dma descriptors indexes are only initialized on the probe function.

If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.

So an interface could be left in an usable state after ifdow/ifup.

This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we rely on rtnl locking in bond_set_rx_mode(), however it's not
always the case:

RTNL: assertion failed at drivers/net/bonding/bond_main.c (3391)
...
 [<ffffffff81651ca5>] dump_stack+0x54/0x74
 [<ffffffffa029e717>] bond_set_rx_mode+0xc7/0xd0 [bonding]
 [<ffffffff81553af7>] __dev_set_rx_mode+0x57/0xa0
 [<ffffffff81557ff8>] __dev_mc_add+0x58/0x70
 [<ffffffff81558020>] dev_mc_add+0x10/0x20
 [<ffffffff8161e26e>] igmp6_group_added+0x18e/0x1d0
 [<ffffffff81186f76>] ? kmem_cache_alloc_trace+0x236/0x260
 [<ffffffff8161f80f>] ipv6_dev_mc_inc+0x29f/0x320
 [<ffffffff8161f9e7>] ipv6_sock_mc_join+0x157/0x260
...

Fix this by using RCU primitives.
Reported-by: NJoe Lawrence <joe.lawrence@stratus.com>
Tested-by: NJoe Lawrence <joe.lawrence@stratus.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.

In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.

Also while at it static-ize moxart_mac_driver.
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

removes following warnings-
drivers/net/phy/marvell.c:37: WARNING: Use #include <linux/io.h> instead of <asm/io.h>
drivers/net/phy/marvell.c:39: WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: NAvinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x makes a dangerous use of skb_is_gso_v6().

It should first make sure skb is a gso packet
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.

When multi queue support will be added some changes to Byte Queue
handling is needed.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes it possible to use some more advanced queuing
techniques with this driver.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Move sysctl_local_ports from a global variable into struct netns_ipv4.
- Modify inet_get_local_port_range to take a struct net, and update all
  of the callers.
- Move the initialization of sysctl_local_ports into
   sysctl_net_ipv4.c:ipv4_sysctl_init_net from inet_connection_sock.c

v2:
- Ensure indentation used tabs
- Fixed ip.h so it applies cleanly to todays net-next

v3:
- Compile fixes of strange callers of inet_get_local_port_range.
  This patch now successfully passes an allmodconfig build.
  Removed manual inlining of inet_get_local_port_range in ipv4_local_port_range
Originally-by: NSamya <samya@twitter.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.

For instance:

	fsl,cksel = <0>;

for using external (TSEC_TMR_CLK input) high precision timer
reference clock.

Other acceptable values:

	<1> : eTSEC system clock
	<2> : eTSEC1 transmit clock
	<3> : RTC clock input

When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: NAida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 894116bd.

I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567

Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:

dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.

The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification.  With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are.  This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device.  Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave.  But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error

Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.

This is also needed for the ALLMULTI flag

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: NMark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: NJoseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: NPeter Korsgaard <peter@korsgaard.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a bug that netback routines netbk/xenvif_skb_count_slots and
netbk/xenvif_gop_frag_copy disagreed with each other, which caused
netback to push wrong number of responses to netfront, which caused
netfront to eventually crash. The bug was fixed in 6e43fc04
("xen-netback: count number required slots for an skb more carefully").

Commit 6e43fc04 focused on backport-ability. The drawback with the
existing packing scheme is that the ring is not used effeciently, as
stated in 6e43fc04.

skb->data like:
    |        1111|222222222222|3333        |

is arranged as:
    |1111        |222222222222|3333        |

If we can do this:
    |111122222222|22223333    |
That would save one ring slot, which improves ring effeciency.

This patch effectively reverts 6e43fc04. That patch made count_slots
agree with gop_frag_copy, while this patch goes the other way around --
make gop_frag_copy agree with count_slots. The end result is that they
still agree with each other, and the ring is now arranged like:
    |111122222222|22223333    |

The patch that improves packing was first posted by Xi Xong and Matt
Wilson. I only rebase it on top of net-next and rewrite commit message,
so I retain all their SoBs. For more infomation about the original bug
please refer to email listed below and commit message of 6e43fc04.

Original patch:
http://lists.xen.org/archives/html/xen-devel/2013-07/msg00760.htmlSigned-off-by: NXi Xiong <xixiong@amazon.com>
Reviewed-by: NMatt Wilson <msw@amazon.com>
[ msw: minor code cleanups, rewrote commit message, adjusted code
  to count RX slots instead of meta structures ]
Signed-off-by: NMatt Wilson <msw@amazon.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
[ liuw: rebased on top of net-next tree, rewrote commit message, coding
  style cleanup. ]
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: NIan Campbell <Ian.Campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's a forgotten function declaration, which was removed some time ago
already.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: NPaul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch proposes to remove the IRQF_DISABLED flag
from drivers/net/hamradio/baycom_*

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.

The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').

CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: NAleksander Morgado <aleksander@lanedo.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Acked-by: NChristian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>