Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.

[JD: Some more fixes.]
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Tested-by: NMike Rapoport <mike@compulab.co.il>
Tested-by: NEric Miao <ymiao3@marvell.com>

Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:

  CC      drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SB700 SATA controller can support 64 bit DMA, the previous commit
badc2341 was added with
careless reference to SB600, which should be modified by this patch.
Signed-off-by: NShane Huang <shane.huang@amd.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.

> >>> And the behaviour I see is very bizarre.

>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...

This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.

Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).

One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Acked-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

AHCI needs sorting too but this deals with the old interface
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes the following compile error caused by commit
3a2d5b70 ("PM: Introduce
PM_EVENT_HIBERNATE callback state")

    CC [M]  drivers/usb/host/u132-hcd.o
  drivers/usb/host/u132-hcd.c: In function ‘u132_suspend’:
  drivers/usb/host/u132-hcd.c:3224: error: expected expression before ‘int’
  drivers/usb/host/u132-hcd.c:3225: error: ‘ports’ undeclared (first use in this function)
  ...
Signed-off-by: NMirco Tischler <mt-ml@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When asked to blink LEDs the tg3 driver behaves when using:
	ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time).  The tg3 driver
interprets this as blink once.  All drivers should have the same
behaviour.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NOliver Pinter <oliver.pntr@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Because of some board issues, we need to disable parallel detect on
an HP blade.  Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous patches to workaround the 5706S on an HP blade were not
sufficient.  The link state still does not change properly in some
cases.  This patch adds polling to make it completely reliable.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Fix build 'make randconfig' build warning spotted by Toralf Foerster:

drivers/scsi/mvsas.c: In function 'mvs_hexdump':
drivers/scsi/mvsas.c:715: error: implicit declaration of function 'isalnum'

- Remove unneeded prototypes (spotted by hch)
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adding the same item to a given linked list more than once is guaranteed
to break and corrupt the list.  This is however what we do in dmi_scan
since commit 79da4721 ("x86: fix DMI out
of memory problems").

Given that there is absolutely no interest in saving empty OEM strings
anyway, I propose the simple and efficient fix below: we discard the empty
OEM strings altogether.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NParag Warudkar <parag.warudkar@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix following warnings:
WARNING: drivers/video/built-in.o(.text+0x7c64a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c65d): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c679): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c699): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/video/built-in.o(.text+0x7c69f): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3676): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa3689): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36a5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36c5): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: drivers/built-in.o(.text+0xa36cb): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a079a): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ad): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07c9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07e9): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan
WARNING: vmlinux.o(.text+0x4a07ef): Section mismatch in reference from the function param_set_scroll() to the variable .devinit.data:ypan

Remove __devinitdata annotation from the variable ypan.
Signed-off-by: NSergio Luis <sergio@larces.uece.br>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

NBD doesn't work well with CFQ (or AS) schedulers, so let's default to
something else.

The two problems I have experienced with nbd and cfq are:

1) nbd hangs with cfq on RHEL 5 (2.6.18) -- this may well have been
   fixed

   There's a similar debian bug that has been filed as well:

   http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=447638

   There have been posts to nbd-general mailing list about problems with
   cfq and nbd also.

2) nbd performs about 10% better (the last time I tested) with deadline
   vs.  cfq (the overhead of cfq doesn't provide much advantage to nbd [not
   being a real disk], and you end up going through the I/O scheduler on
   the nbd server anyway, so it makes sense that deadline is better with
   nbd)
Signed-off-by: NPaul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that we gather on-board devices from both DMI types 10 and 41, there is
a possibility that we list the same device twice.  In order to not confuse
drivers, and also to save memory, make sure that we do not add duplicate
devices to the dmi_devices list.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For the "cmos" RTC, have /proc/driver/rtc say whether HPET based IRQ
emulation is in effect.  Given the problems we've had with this particular
hardware maldesign (and the fact that most BIOS code seems not to provide
the IRQ routing needed to use the saner HPET modes), this should help
troubleshooting.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes a sequencing bug in spi driver pxa2xx_spi.c in which the chip select
for a transfer may be asserted before the clock polarity is set on the
interface.  As a result of this bug, the clock signal may have the wrong
polarity at transfer start, so it may need to make an extra half transition
before the intended clock/data signals begin.  (This probably means all
transfers are one bit out of sequence.)

This only occurs on the first transfer following a change in clock polarity
in systems using more than one more than one such polarity.  The fix
assures that the clock mode is properly set before asserting chip select.

This bug was introduced in a patch merged on 2006/12/10, kernel 2.6.20.
The patch defines an additional bit in: include/asm-arm/arch-pxa/regs-ssp.h
for 2.6.25 and newer kernels but this addition must be made in:
include/asm-arm/arch-pxa/pxa-regs.h for kernels between 2.6.20 and 2.6.24,
inclusive
Signed-off-by: NNed Forrester <nforrester@whoi.edu>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The atmel_spi driver does not initialize clock polarity correctly (except for
at91rm9200 CS0 channel) in some case.

The atmel_spi driver uses gpio-controlled chipselect.  OTOH spi clock signal
is controlled by CSRn.CPOL bit, but this register controls clock signal
correctly only in 'real transfer' duration.  At the time of cs_activate()
call, CSRn.CPOL will be initialized correctly, but the controller do not know
which channel is to be used next, so clock signal will stay at the inactive
state of last transfer.  If clock polarity of new transfer and last transfer
was differ, new transfer will start with wrong clock signal state.

For example, if you started SPI MODE 2 or 3 transfer after SPI MODE 0 or 1
transfer, the clock signal state at the assertion of chipselect will be low.
Of course this will violates SPI transfer.

This patch is short term solution for this problem.  It makes all CSRn.CPOL
match for the transfer before activating chipselect.  For longer term, the
best fix might be to let NPCS0 stay selected permanently in MR and overwrite
CSR0 with to the new slave's settings before asserting CS.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We should only return IRQ_HANDLED when we actually found something to
handle. This is important since the USART interrupt handler may be
shared with the timer interrupt on some chips.
Pointed-out-by: Nmichael <trimarchi@gandalf.sssup.it>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following is a clean up and correction of the copyright holding
entities for the files associated with the intel iommu code.

Signed-off-by: <mgross@linux.intel.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During the last step of hibernation in the "platform" mode (with the
help of ACPI) we use the suspend code, including the devices'
->suspend() methods, to prepare the system for entering the ACPI S4
system sleep state.

But at least for some devices the operations performed by the
->suspend() callback in that case must be different from its operations
during regular suspend.

For this reason, introduce the new PM event type PM_EVENT_HIBERNATE and
pass it to the device drivers' ->suspend() methods during the last phase
of hibernation, so that they can distinguish this case and handle it as
appropriate.  Modify the drivers that handle PM_EVENT_SUSPEND in a
special way and need to handle PM_EVENT_HIBERNATE in the same way.

These changes are necessary to fix a hibernation regression related
to the i915 driver (ref. http://lkml.org/lkml/2008/2/22/488).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Tested-by: NJeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In current mainline, __devinit qpti_sbus_probe() still is calling __init
qpti_chain_add().  Change occurrences of __init to __devinit to fix.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Convert rough draft Marvell 6440 driver to a working driver.
Added support for SAS and SATA devices, hotplug, wide port, and expanders.
Signed-off-by: NKe Wei <kewei@marvell.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Make sure the restoration correctly restores the AR registers by
flipping the ARX register into index mode before doing anything.

Without this, some people have had the text mode restore all green.
Signed-off-by: NJesse Barnes <jesse.barnes@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in.  It should be checking for
commands which are on the same logical unit as the one passed in.  Fix
this by checking target pointer and LUN for equality.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The clear nexus I_T and clear nexus I_T_L functions in the aic94xx
specify the SUSPEND_TX flag which causes the sequencer to be suspended
until it receives a RESUME_TX.  Unfortunately, nothing ever sends the
resume, so the sequencer on the link is stopped forever, leading to
eventual timeouts and I/O errors.

Since clear nexus commands are only executed as part of error recovery,
it's perfectly fine to keep the sequencer running on the link ... as
soon as the recovery function is completed, we'll send it the commands
to retry.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Remove the now useless counting of adjacent pages from the debugging code in
to make it compile when DEBUG is set non-zero.
Signed-off-by: NKai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).

scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NEd Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.

scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.

stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NEd Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Commit 3163f725 introduced locking in
lpfc_sli_hbqbuf_fill_hbqs, but missed unlocking on one exit.
Reported-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Acked-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status.  Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test
Signed-off-by: NDavid C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The libsas error handler has two fairly fatal bugs

1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early.  This
   happens if the task completes after it has been aborted but before
   the error handler starts up.  Because scsi_eh_finish_cmd()
   decrements host_failed and adds the task to the done list, the
   error handler start check (host_failed == host_busy) never passes
   and the eh never starts.

2. The multiple task completion paths sas_scsi_clear_queue_... all
   simply delete the task from the error queue.  This causes it to
   disappear into the ether, since a command must be placed on the
   done queue to be finished off by the error handler.  This behaviour
   causes the HBA to hang on pending commands.

Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired).  This keeps the task in the error
handling queue until the eh starts.

Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().

Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>