Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 02 9月, 2021 2 次提交
  3. 06 8月, 2021 1 次提交
    • V
      net: dsa: don't disable multicast flooding to the CPU even without an IGMP querier · c73c5708
      由 Vladimir Oltean 提交于 
      Commit 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).

And commit a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.

The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:

- ICMP6 neighbor solicitation messages are unregistered multicast
  packets as far as the bridge is concerned. So if we stop flooding
  multicast, the outside world cannot ping the bridge device's IPv6
  link-local address.

- There might be foreign interfaces bridged with our DSA switch ports
  (sending a packet towards the host does not necessarily equal
  termination, but maybe software forwarding). So if there is no one
  interested in that multicast traffic in the local network stack, that
  doesn't mean nobody is.

- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
  the bridge is concerned. This should reach the CPU port.

- The switch driver might not do FDB partitioning. And since we don't
  even bother to do more fine-grained flood disabling (such as "disable
  flooding _from_port_N_ towards the CPU port" as opposed to "disable
  flooding _from_any_port_ towards the CPU port"), this breaks standalone
  ports, or even multiple bridges where one has an IGMP querier and one
  doesn't.

Reverting the logic makes all of the above work.

Fixes: a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c73c5708
  5. 23 6月, 2021 1 次提交
  7. 10 6月, 2021 1 次提交
    • F
      net: dsa: b53: Do not force CPU to be always tagged · 2c32a3d3
      由 Florian Fainelli 提交于 
      Commit ca893194 ("net: dsa: b53: Keep CPU port as tagged in all
VLANs") forced the CPU port to be always tagged in any VLAN membership.
This was necessary back then because we did not support Broadcom tags
for all configurations so the only way to differentiate tagged and
untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU
port into being always tagged.

With most configurations enabling Broadcom tags, especially after
8fab459e ("net: dsa: b53: Enable Broadcom tags for 531x5/539x
families") we do not need to apply this unconditional force tagging of
the CPU port in all VLANs.

A helper function is introduced to faciliate the encapsulation of the
specific condition requiring the CPU port to be tagged in all VLANs and
the dsa_switch_ops::untag_bridge_pvid boolean is moved to when
dsa_switch_ops::setup is called when we have already determined the
tagging protocol we will be using.
Reported-by: NMatthew Hagan <mnhagan88@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Tested-by: NMatthew Hagan <mnhagan88@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2c32a3d3
  9. 18 3月, 2021 1 次提交
  11. 12 3月, 2021 1 次提交
  13. 11 3月, 2021 1 次提交
  15. 24 2月, 2021 2 次提交
  17. 15 2月, 2021 2 次提交
  19. 13 2月, 2021 1 次提交
    • V
      net: dsa: act as passthrough for bridge port flags · a8b659e7
      由 Vladimir Oltean 提交于 
      There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.

One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.

Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.

Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it.  If it does, there
will need to be a dedicated .port_set_mrouter anyway.

So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.

The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:

behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)

so there was no reason to entangle them in the first place.

Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a8b659e7
  21. 20 1月, 2021 1 次提交
  23. 16 1月, 2021 1 次提交
    • V
      net: dsa: set configure_vlan_while_not_filtering to true by default · 0ee2af4e
      由 Vladimir Oltean 提交于 
      As explained in commit 54a0ed0d ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.

New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.

Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.

The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.

The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.

Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.

No behavior change except for the added prints is intended at this time.

$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[   60.315148] br0: port 1(sw0p2) entered blocking state
[   60.320350] br0: port 1(sw0p2) entered disabled state
[   60.327839] device sw0p2 entered promiscuous mode
[   60.334905] br0: port 1(sw0p2) entered blocking state
[   60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NKurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      0ee2af4e
  25. 12 1月, 2021 4 次提交
    • V
      net: dsa: remove the transactional logic from VLAN objects · 1958d581
      由 Vladimir Oltean 提交于 
      It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.

So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.

It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      1958d581
    • V
      net: dsa: remove the transactional logic from MDB entries · a52b2da7
      由 Vladimir Oltean 提交于 
      For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.

Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      a52b2da7
    • V
      net: switchdev: remove the transaction structure from port attributes · bae33f2b
      由 Vladimir Oltean 提交于 
      Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.

Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8ece ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.

It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.

This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.

In part, this patch contains a revert of my previous commit 2e554a7a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").

For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
  implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
  done mechanically, by pasting the implementation twice, then only
  keeping the code that would get executed during prepare phase on top,
  then only keeping the code that gets executed during the commit phase
  on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
  multicast router could be converted right away. But the ageing time
  could not, so a shim was introduced and this was left for a further
  commit.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      bae33f2b
    • V
      net: switchdev: remove vid_begin -> vid_end range from VLAN objects · b7a9e0da
      由 Vladimir Oltean 提交于 
      The call path of a switchdev VLAN addition to the bridge looks something
like this today:

        nbp_vlan_init
        |  __br_vlan_set_default_pvid
        |  |                       |
        |  |    br_afspec          |
        |  |        |              |
        |  |        v              |
        |  | br_process_vlan_info  |
        |  |        |              |
        |  |        v              |
        |  |   br_vlan_info        |
        |  |       / \            /
        |  |      /   \          /
        |  |     /     \        /
        |  |    /       \      /
        v  v   v         v    v
      nbp_vlan_add   br_vlan_add ------+
       |              ^      ^ |       |
       |             /       | |       |
       |            /       /  /       |
       \ br_vlan_get_master/  /        v
        \        ^        /  /  br_vlan_add_existing
         \       |       /  /          |
          \      |      /  /          /
           \     |     /  /          /
            \    |    /  /          /
             \   |   /  /          /
              v  |   | v          /
              __vlan_add         /
                 / |            /
                /  |           /
               v   |          /
   __vlan_vid_add  |         /
               \   |        /
                v  v        v
      br_switchdev_port_vlan_add

The ranges UAPI was introduced to the bridge in commit bdced7ef
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.

Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328b ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:

br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink

Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.

In the meantime, commits such as 0944d6b5 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.

Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and  __vlan_add
(the latter coming from commit 9c86ce2c ("net: bridge: Notify about
bridge VLANs")).

That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.

Let's go off and finish the job of commit 29ab586c by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60d
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).

Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.

And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.

Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      b7a9e0da
  27. 10 1月, 2021 1 次提交
  29. 05 10月, 2020 1 次提交
    • V
      net: dsa: propagate switchdev vlan_filtering prepare phase to drivers · 2e554a7a
      由 Vladimir Oltean 提交于 
      A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
  (the DSA framework just checks for the presence of the .port_vlan_add
  and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2e554a7a
  31. 03 10月, 2020 1 次提交
  33. 24 9月, 2020 1 次提交
    • F
      net: dsa: b53: Configure VLANs while not filtering · ed409f3b
      由 Florian Fainelli 提交于 
      Update the B53 driver to support VLANs while not filtering. This
requires us to enable VLAN globally within the switch upon driver
initial configuration (dev->vlan_enabled).

We also need to remove the code that dealt with PVID re-configuration in
b53_vlan_filtering() since that function worked under the assumption
that it would only be called to make a bridge VLAN filtering, or not
filtering, and we would attempt to move the port's PVID accordingly.

Now that VLANs are programmed all the time, even in the case of a
non-VLAN filtering bridge, we would be programming a default_pvid for
the bridged switch ports.

We need the DSA receive path to pop the VLAN tag if it is the bridge's
default_pvid because the CPU port is always programmed tagged in the
programmed VLANs. In order to do so we utilize the
dsa_untag_bridge_pvid() helper introduced in the commit before within
net/dsa/tag_brcm.c.
Acked-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ed409f3b
  35. 10 9月, 2020 1 次提交
  37. 04 9月, 2020 2 次提交
  39. 24 8月, 2020 1 次提交
  41. 22 8月, 2020 1 次提交
    • T
      net: dsa: b53: check for timeout · 774d977a
      由 Tom Rix 提交于 
      clang static analysis reports this problem

b53_common.c:1583:13: warning: The left expression of the compound
  assignment is an uninitialized value. The computed value will
  also be garbage
        ent.port &= ~BIT(port);
        ~~~~~~~~ ^

ent is set by a successful call to b53_arl_read().  Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.

So add -ETIMEDOUT to the switch statement.  Because
b53_arl_op_wait() already prints out a message, do not add another
one.

Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: NTom Rix <trix@redhat.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      774d977a
  43. 01 7月, 2020 2 次提交
  45. 28 5月, 2020 1 次提交
  47. 01 5月, 2020 4 次提交
  49. 23 4月, 2020 4 次提交
  51. 31 3月, 2020 1 次提交