This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves where the jumbo capable and msi support flags are
located.  This is prep work for the addition of msix support flags.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch converts the code to use the PHY_IS_FET flag rather than the
ASIC revision to decide whether or not to use FET paths.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's phys come in two distinctly different register layouts.  For
the lack of an official term to distinguish between the two formats, we
can loosely categorize them by their fast ethernet or gigabit ethernet
transceiver description.  This patch creates the (driver-internal) Fast
Ethernet Transceiver (FET) namespace and converts the 5906 EPHY
definitions over.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch tunes the timeouts the CPMU uses to decide when to switch
from the clocks output by the PHY to internal clock sources.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 57788 and removes support for the 57720
which was never released.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prevents a tx BD corruption bug by preventing the device from
powering down the PLL from L1 if the link speed is 10Mbps or 100Mbps.

The same bits are also used to prevent a system hang during chip reset
resulting from a complicated set of events that ultimately leads to
PCIe block register corruption.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some PCIe link receiver errors by decreasing the internal
electrical idle timeout.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch restricts the CLKREQ bugfix to the A0 and A1 revisions
of 57780 ASIC rev chips.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On rare occasions, send BD corruptions can occur.  This patch
fixes the problem by increasing the L1 entry threshold to 4
milliseconds.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some 57780 ASIC revision parts do not have NVRAM.  Code the driver so
that it is tolerant of this configuration.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver's ISR is coded to accept interrupts as its own if the
status block tag does not equal the last tag the driver has seen.  The
last_tag field is updated from tg3_poll.  In a screaming interrupt
situation from another device sharing tg3's IRQ, tg3_poll does not get
a chance to be called, so the last_tag will always be out of sync with
the status block tag.  Consequently, the driver will continually
declare the screaming interrupts as its own, thus thwarting the
screaming interrupt detection logic.

This patch solves the problem by creating a new last_irq_tag member and
recording the status block tag in the ISR.  The ISR then checks the
last_irq_tag for interrupt ownership.

Many thanks to John Marvin for the detailed bug report and analysis and
Michael Chan for the bugfix.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Tested-by: NJohn Marvin <jsm@fc.hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds version reporting for hardware selfboot.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to report the DASH firmware version.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds code to obtain the bootcode version for versions
of bootcode that do not use the new method.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch modifies how the tg3 driver handles device firmware.

The patch starts by consolidating David Woodhouse's earlier patch under
the same name.  Specifically, the patch moves the request_firmware call
into a separate tg3_request_firmware() function and calls that function
from tg3_open() rather than tg3_init_one().

The patch then goes on to limit the number of devices that will make
request_firmware calls.  The original firmware patch unnecessarily
requested TSO firmware for devices that did not need it.  This patch
reduces the set of devices making TSO firmware patches to approximately
the following device set : 5703, 5704, and 5705.

Finally, the patch reduces the effects of a request_firmware() failure.
For those devices that are requesting TSO firmware, the driver will turn
off the TSO capability.  If TSO firmware becomes available at a later
time, the device can be closed and then opened again to reacquire the
TSO capability.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware blob looks like this...
        u8 firmware_major
        u8 firmware_minor
        u8 firmware_fix
        u8 pad
        __be32 start_address
        __be32 length (total, including BSS sections to be zeroed)
        data... (in __be32 words, which is native for the firmware)
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up the tg3 header file by removing the preprocessor
definitions for standard PCI configuration space registers.  The driver
should be using the standard definitions when needed.  The patch
continues by removing redundant PHY related definitions and reorganizes
some of the remaining entries.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the pci_bist and pci_hdr_type members from the
device structure and removes the code that references them.  They are
not really used.

The patch rounds out the changes by moving the pci_cmd member to plug
a structure hole that would have been created.  On 32-bit systems, this
movement removes a subsequent structure hole later in the structure. On
64-bit systems though, the movement merely consolidates two holes into
one larger hole.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch attempts to make the relationship between IPV6 checksum
offload and IPV6 LSO more obvious.  The patch also toggles a bit
needed for IPV6 LSO on 5785 and 57780 devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.

The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 57780 ASIC revision.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch extracts the bootcode firmware version from the alternate
selfboot patch NVRAM format.  This format is used on the 5784, 5761 and
some newer devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GPHY Autopowerdown (APD) is a way to save power when energy is not
detected on the wire.  At the moment, only the 5784 and 5761 are
capable of enabling this mode.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables CLKREQ at 10Mbps and 100Mbps to workaround a TX BD
corruption issue.  This problem only affects the 5784 and 5761 (and
57780 AX) ASIC revisions.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines support for the 5785 device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows WOL to be enabled for Broadcom phys under phylib
control.  The only exception is the AC131, which has a completely
different register set.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag.  It only
used twice in non-fast paths.  This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.

When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames.  Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver.  The first hunk of this patch preserves this setting.

The second hunk of this patch wipes out the driver present signature of
the APE memory space.  By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the 5761S chip variants.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAndy Fleming <afleming@freescale.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The git commit 7c5026aa ("tg3: Add
link state reporting to UMP firmware") introduced code that waits for
previous firmware events to be serviced before attempting to submit a
new event.  Unfortunately that patch contained a bug that cause the
driver to wait 2.5 seconds, rather than 2.5 milliseconds as intended.
This patch fixes that bug.

This bug revealed that not all firmware versions service driver events
though.  Since we do not know which versions of the firmware do and don't
service these events, the driver needs some way to minimize the effects
of the delay.  This patch solves the problem by recording a jiffies
timestamp when it submits an event to the hardware.  If the jiffies
counter shows that 2.5 milliseconds have already passed, a wait is not
needed and the driver can proceed to submit a new event.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's DASH (Desktop and mobile Architecture for System Hardware)
implementation requires that the driver preserve particular register
settings.  If the driver does not preserve them, communication with
the DASH firmware will be lost.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver resets the chip while the APE is performing a register
access, that register access will never complete and the APE will hang
indefinitely.  To prevent this race condition, the driver must acquire
an APE mutex before resetting the chip.  The APE will not attempt a
register access until it acquires this lock.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some options obtained through shared memory.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch added the 5785 device ID and ASIC revision to the code.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces the libphy support.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>