driver inclusion
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I7DZ8S
CVE: NA

----------------------------------------------------------------------

When the current HiSilicon USB xhci controller formats the faulty
U disk, it will trigger a controller exception error. This will
cause errors in the control logic of the xhci controller and
driver software. In the end, all USB devices on the xhci controller
cannot be used.

By introducing a noop command operation, restore the logic of the
xhci controller and driver software, and restore all USB devices
on the xhci controller to normal.
Signed-off-by: NLongfang Liu <liulongfang@huawei.com>
(cherry picked from commit 1a869403)

stable inclusion
from stable-v5.10.153
commit 678d2cc2041cc6ce05030852dce9ad42719abcfc
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=678d2cc2041cc6ce05030852dce9ad42719abcfc

--------------------------------

commit 5aed5b7c upstream.

Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.

If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.

So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.

Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.

This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)

Cc: stable@vger.kernel.org
Reported-by: NMarek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: NMarek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

stable inclusion
from stable-v5.10.153
commit 3b250824b6d3f109c8c18652280f7120c3803545
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=3b250824b6d3f109c8c18652280f7120c3803545

--------------------------------

commit 34cd2db4 upstream.

Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.

This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.

A more generic solution to power off ports at shutdown was attempted in
commit 83810f84 ("xhci: turn off port power in shutdown")
but it caused regression.

Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.

Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

Conflicts:
	drivers/usb/host/xhci.h

stable inclusion
from stable-v5.10.153
commit 228101fc832f0330f266e1f4002bd969a3be7850
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=228101fc832f0330f266e1f4002bd969a3be7850

--------------------------------

commit 4f547472 upstream.

This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.

ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0

Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3

Cc: stable@vger.kernel.org
Signed-off-by: NJens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-2-mathias.nyman@intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

stable inclusion
from stable-v5.10.153
commit 2bc4f99ee24391bc05f0f464c4414ab0ad7b4f74
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=2bc4f99ee24391bc05f0f464c4414ab0ad7b4f74

--------------------------------

commit fb8f60dd upstream.

When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
Signed-off-by: NJustin Chen <justinpopo6@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Fixes: efed421a ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/1664997235-18198-1-git-send-email-justinpopo6@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

stable inclusion
from stable-v5.10.153
commit e440957f9c8bedae784f718c42207af222c25818
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e440957f9c8bedae784f718c42207af222c25818

--------------------------------

commit 308c316d upstream.

The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.

Fixes: 72246da4 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: NThinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: NJeff Vanhoof <jdv1029@gmail.com>
Tested-by: NJeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

stable inclusion
from stable-v5.10.153
commit fb074d622ccc7e3999cde47f18ea7f8970b09d11
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=fb074d622ccc7e3999cde47f18ea7f8970b09d11

--------------------------------

commit f78961f8 upstream.

When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.

Note that only the last TRB of chained TRBs has its status updated with
missed isoc.

Fixes: 72246da4 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: NJeff Vanhoof <jdv1029@gmail.com>
Reported-by: NDan Vacura <w36195@motorola.com>
Signed-off-by: NThinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: NJeff Vanhoof <jdv1029@gmail.com>
Tested-by: NJeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

stable inclusion
from stable-v5.10.153
commit c29fcef5791d4c2782696f5a59316b3d92248c57
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I64YCA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=c29fcef5791d4c2782696f5a59316b3d92248c57

--------------------------------

commit fc4ade55 upstream.

NVIDIA Jetson devices in Force Recovery mode (RCM) do not support
suspending, ie. flashing fails if the device has been suspended. The
devices are still visible in lsusb and seem to work otherwise, making
the issue hard to debug. This has been discovered in various forum
posts, eg. [1].

The patch has been tested on NVIDIA Jetson AGX Xavier, but I'm adding
all the Jetson models listed in [2] on the assumption that they all
behave similarly.

[1]: https://forums.developer.nvidia.com/t/flashing-not-working/72365
[2]: https://docs.nvidia.com/jetson/archives/l4t-archived/l4t-3271/index.html#page/Tegra%20Linux%20Driver%20Package%20Development%20Guide/quick_start.htmlSigned-off-by: NHannu Hartikainen <hannu@hrtk.in>
Cc: stable <stable@kernel.org>  # after 6.1-rc3
Link: https://lore.kernel.org/r/20220919171610.30484-1-hannu@hrtk.inSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLipeng Sang <sanglipeng1@jd.com>

mainline inclusion
from mainline-v6.2-rc5
commit d18dcfe9
category: bugfix
bugzilla: https://gitee.com/src-openeuler/kernel/issues/I66IZK
CVE: CVE-2022-4382

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d18dcfe9860e842f394e37ba01ca9440ab2178f4

----------------------------------------------------------------------

The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem.  In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it.  The output from KASAN says,
in part:

BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689

CPU: 0 PID: 18689 Comm: syz-executor126 Not tainted 6.1.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
 <TASK>
...
 atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
 __refcount_sub_and_test include/linux/refcount.h:272 [inline]
 __refcount_dec_and_test include/linux/refcount.h:315 [inline]
 refcount_dec_and_test include/linux/refcount.h:333 [inline]
 put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
 gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
 deactivate_locked_super+0xa7/0xf0 fs/super.c:332
 vfs_get_super fs/super.c:1190 [inline]
 get_tree_single+0xd0/0x160 fs/super.c:1207
 vfs_get_tree+0x88/0x270 fs/super.c:1531
 vfs_fsconfig_locked fs/fsopen.c:232 [inline]

The simplest solution is to ensure that gadgetfs_fill_super() and
gadgetfs_kill_sb() are serialized by making them both acquire a new
mutex.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+33d7ad66d65044b93f16@syzkaller.appspotmail.com
Reported-and-tested-by: NGerald Lee <sundaywind2004@gmail.com>
Link: https://lore.kernel.org/linux-usb/CAO3qeMVzXDP-JU6v1u5Ags6Q-bb35kg3=C6d04DjzA9ffa5x1g@mail.gmail.com/
Fixes: e5d82a73 ("vfs: Convert gadgetfs to use the new mount API")
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Y6XCPXBpn3tmjdCC@rowland.harvard.eduSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NZhangPeng <zhangpeng362@huawei.com>
Reviewed-by: Ntong tiangen <tongtiangen@huawei.com>
Reviewed-by: NXiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit b8bbae3236ab7dccc66c42bc3f7cdbcfc0786e54
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b8bbae3236ab7dccc66c42bc3f7cdbcfc0786e54

--------------------------------

[ Upstream commit bce2b053 ]

In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.

Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.

Note that this is found by KMSAN, so only kernel compilation
is tested.

Reported-by: syzbot+79832d33eb89fb3cd092@syzkaller.appspotmail.com
Signed-off-by: NDongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220922134847.1101921-1-dzm91@hust.edu.cnSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit 3a5a34ed9d68ffb008a60946ac1619b40a111716
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=3a5a34ed9d68ffb008a60946ac1619b40a111716

--------------------------------

[ Upstream commit ad5dbfc1 ]

This reverts commit 86d92f54,
which fix the timeout issue for "Samsung Fit Flash".

But the commit affects not only "Samsung Fit Flash" but also other usb
storages that use the same controller and causes severe performance
regression.

 # hdparm -t /dev/sda (without the quirk)
 Timing buffered disk reads: 622 MB in  3.01 seconds = 206.66 MB/sec

 # hdparm -t /dev/sda (with the quirk)
 Timing buffered disk reads: 220 MB in  3.00 seconds =  73.32 MB/sec

The commit author mentioned that "Issue was reproduced after device has
bad block", so this quirk should be applied when we have the timeout
issue with a device that has bad blocks.

We revert the commit so that we apply this quirk by adding kernel
paramters using a bootloader or other ways when we really need it,
without the performance regression with devices that don't have the
issue.
Signed-off-by: Nsunghwan jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20220913114913.3073-1-onenowy@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit acf0006f2b2b2ca672988875fd154429aafb2a9b
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=acf0006f2b2b2ca672988875fd154429aafb2a9b

--------------------------------

[ Upstream commit eea4c860 ]

The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.

Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt);
Signed-off-by: NRobin Guo <guoweibin@inspur.com>
Link: https://lore.kernel.org/r/20220906102119.1b071d07a8391ff115e6d1ef@inspur.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit 91271a3e772e180bbb8afb114c72fd294a02f93d
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=91271a3e772e180bbb8afb114c72fd294a02f93d

--------------------------------

[ Upstream commit 7e271f42 ]

xhci_alloc_stream_info() allocates stream context array for stream_info
->stream_ctx_array with xhci_alloc_stream_ctx(). When some error occurs,
stream_info->stream_ctx_array is not released, which will lead to a
memory leak.

We can fix it by releasing the stream_info->stream_ctx_array with
xhci_free_stream_ctx() on the error path to avoid the potential memory
leak.
Signed-off-by: NJianglei Nie <niejianglei2021@163.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-2-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit 48727117bd6243f1c7fc6ed35ad131d27c505be8
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=48727117bd6243f1c7fc6ed35ad131d27c505be8

--------------------------------

[ Upstream commit c69400b0 ]

The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJustin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit c13d0d2f5a4806cef87693966091b5fd3f5c225f
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=c13d0d2f5a4806cef87693966091b5fd3f5c225f

--------------------------------

[ Upstream commit 8bd954c5 ]

Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJustin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

 Conflicts:
	drivers/usb/host/xhci.h

stable inclusion
from stable-v5.10.150
commit 7efdd91d54cbf42a8079ebbdc677a16984b2f9b7
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=7efdd91d54cbf42a8079ebbdc677a16984b2f9b7

--------------------------------

[ Upstream commit 24b7ba2f ]

When opts->pnp_string is changed with configfs, new memory is allocated for
the string. It does not, however, update dev->pnp_string, even though the
memory is freed. When rquesting the string, the host then gets old or
corrupted data rather than the new string. The ieee 1284 id string should
be allowed to change while the device is connected.

The bug was introduced in commit fdc01cc2 ("usb: gadget: printer:
Remove pnp_string static buffer"), which changed opts->pnp_string from a
char[] to a char*.
This patch changes dev->pnp_string from a char* to a char** pointing to
opts->pnp_string.

Fixes: fdc01cc2 ("usb: gadget: printer: Remove pnp_string static buffer")
Signed-off-by: NAlbert Briscoe <albertsbriscoe@gmail.com>
Link: https://lore.kernel.org/r/20220911223753.20417-1-albertsbriscoe@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit cc952e3bf61cf83e51dab80aba656da22dbc6d00
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=cc952e3bf61cf83e51dab80aba656da22dbc6d00

--------------------------------

[ Upstream commit 484d6f7a ]

commit 8b328f80 ("xhci: re-initialize the HC during resume if HCE was
set") introduced a new warning message when the host controller error
was set and re-initializing.

This is expected behavior on some designs which already set
`xhci->broken_suspend` so the new warning is alarming to some users.

Modify the code to only show the warning if this was a surprising behavior
to the XHCI driver.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216470
Fixes: 8b328f80 ("xhci: re-initialize the HC during resume if HCE was set")
Reported-by: NArtem S. Tashkinov <aros@gmx.com>
Signed-off-by: NMario Limonciello <mario.limonciello@amd.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-4-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit beec2f02555c7e9d47fd455f40d7bf7c46fb4b8d
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=beec2f02555c7e9d47fd455f40d7bf7c46fb4b8d

--------------------------------

[ Upstream commit b6155eaf ]

Previously usb_decode_ctrl() only decodes standard control requests, but
it was used for non-standard requests also. If it's non-standard or
unknown standard bRequest, print the Setup data values.

Fixes: af32423a ("usb: dwc3: trace: decode ctrl request")
Signed-off-by: NThinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8d6a30f2f2f953eff833a5bc5aac640a4cc2fc9f.1658971571.git.Thinh.Nguyen@synopsys.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit 9d965a22f65716dc452fd682a89c58db9235ec61
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=9d965a22f65716dc452fd682a89c58db9235ec61

--------------------------------

[ Upstream commit 365038f2 ]

Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Suggested-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/c4d2e010ae2bf67cdfa0b55e6d1deb9339d9d3dc.1615170625.git.chunfeng.yun@mediatek.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b6155eaf ("usb: common: debug: Check non-standard control requests")
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit 20b63631a38a94a7542b570cfee005ff4c0df911
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=20b63631a38a94a7542b570cfee005ff4c0df911

--------------------------------

[ Upstream commit fb95c7cf ]

Add a new function to convert bInterval into the time expressed
in 1us unit.
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/25c8a09b055f716c1e5bf11fea72c3418f844482.1615170625.git.chunfeng.yun@mediatek.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b6155eaf ("usb: common: debug: Check non-standard control requests")
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit c1ef8c66a362979f5c48dd01b808ccecd5497fe4
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=c1ef8c66a362979f5c48dd01b808ccecd5497fe4

--------------------------------

[ Upstream commit 52c2d157 ]

The USB "maximum-speed" property can now take the SSP signaling rate
generation and lane count with these new strings:

"super-speed-plus-gen2x2"
"super-speed-plus-gen2x1"
"super-speed-plus-gen1x2"

Introduce usb_get_maximum_ssp_rate() to parse for the corresponding
usb_ssp_rate enum. The original usb_get_maximum_speed() will return
USB_SPEED_SUPER_PLUS if it matches one of these new strings.
Signed-off-by: NThinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f8ed896313d8cd8e2d2b540fc82db92b3ddf8a47.1611106162.git.Thinh.Nguyen@synopsys.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b6155eaf ("usb: common: debug: Check non-standard control requests")
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.150
commit b239a0993aa2d603c11bd94fa4a93670fb117d45
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0XA

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b239a0993aa2d603c11bd94fa4a93670fb117d45

--------------------------------

commit 37d49519 upstream.

The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream

These hubs suffer from two separate problems:

1) After the host system was suspended and woken up, the hubs appear to
   be in a random state. Some downstream ports (both internal to the
   built-in audio and network controllers, and external to USB sockets)
   may no longer be functional. The exact list of disabled ports (if
   any) changes from wakeup to wakeup. Ports remain in that state until
   the dock is power-cycled, or until the laptop is rebooted.

   Wakeup sources connected to the hubs (keyboard, WoL on the integrated
   gigabit controller) will wake the system up from suspend, but they
   may no longer work after wakeup (and in that case will no longer work
   as wakeup source in a subsequent suspend-wakeup cycle).

   This issue appears in the logs with messages such as:

     usb 1-6.1-port4: cannot disable (err = -71)
     usb 1-6-port2: cannot disable (err = -71)
     usb 1-6.1: clear tt 1 (80c0) error -71
     usb 1-6-port4: cannot disable (err = -71)
     usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
     usb 1-6.4: PM: failed to resume async: error -71
     usb 1-7: reset full-speed USB device number 5 using xhci_hcd
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
     usb 1-6.1-port1: cannot disable (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
     usb 1-6.1-port1: cannot disable (err = -71)

2) Some USB devices cannot be enumerated properly. So far I have only
   seen the issue with USB 3.0 devices. The same devices work without
   problem directly connected to the host system, to other systems or to
   other hubs (even when those hubs are connected to the OneLink+ dock).

   One very reliable reproducer is this USB 3.0 HDD enclosure:
   152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius

   I have seen it happen sporadically with other USB 3.0 enclosures,
   with controllers from different manufacturers, all self-powered.

   Typical messages in the logs:

     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 6, error -62
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 7, error -62
     usb 2-1-port4: attempt power cycle
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 8, error -62
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 9, error -62
     usb 2-1-port4: unable to enumerate USB device

Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:

=======================================================================================
Settings                        USB2 hotplug    USB3 hotplug    State after waking up
---------------------------------------------------------------------------------------

power/control=auto              works           fails           broken

usbcore.autosuspend=-1          works           works           broken
OR power/control=on

power/control=auto              works (1)       works (1)       works
and USB_QUIRK_RESET_RESUME

power/control=on                works           works           works
and USB_QUIRK_RESET_RESUME

HUB_QUIRK_DISABLE_AUTOSUSPEND   works           works           works
and USB_QUIRK_RESET_RESUME

=======================================================================================

In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.

From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.

A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.

Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.

Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.

Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: NJean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

LoongArch inclusion
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6T7XW

--------------------------------

EJ188 has similar problems as the upstream commit
commit a4a251f8 ("usb: xhci: do not perform Soft Retry for some xHCI hosts")
so we add XHCI_NO_SOFT_RETRY quirk for it.
Signed-off-by: NHongchen Zhang <zhanghongchen@loongson.cn>
Change-Id: I6b5153a5bb8f8a7b0fa4f4accb65fb1c00311561

mainline inclusion
from mainline-v5.17-rc1
commit fa0ef938
category: bugfix
bugzilla: https://gitee.com/src-openeuler/kernel/issues/I6IEH4
CVE: CVE-2023-22995

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=fa0ef93868a6062babe1144df2807a8b1d4924d2

--------------------------------

Add the missing platform_device_put() before return from
dwc3_qcom_acpi_register_core in the error handling case.
Signed-off-by: NMiaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211231113641.31474-1-linmq006@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 2bc02355 ("usb: dwc3: qcom: Add support for booting with ACPI")
[Fix conflict due to lack of 8dc6e6dd]
Conflict:
	drivers/usb/dwc3/dwc3-qcom.c
Signed-off-by: NZheng Yejian <zhengyejian1@huawei.com>
Reviewed-by: NXu Kuohai <xukuohai@huawei.com>
Reviewed-by: NXiu Jianfeng <xiujianfeng@huawei.com>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>

stable inclusion
from stable-v5.10.148
commit 638f84a718d99c68ce5a46d24283beecf5d48b7a
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0WL

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=638f84a718d99c68ce5a46d24283beecf5d48b7a

--------------------------------

commit eee48781 upstream.

Add support for Dell 5811e (EM7455) with USB-id 0x413c:0x81c2.
Signed-off-by: NFrank Wunderlich <frank-w@public-files.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.148
commit 3451df3a514cb97c6295f6c788511a6a62140709
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0WL

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=3451df3a514cb97c6295f6c788511a6a62140709

--------------------------------

commit 7bd7ad3c upstream.

The 300 bps rate of SIO devices has been mapped to 9600 bps since
2003... Let's fix the regression.

Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.147
commit efdff533946284ed013f8e062be66e57463304bf
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0W8

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=efdff533946284ed013f8e062be66e57463304bf

--------------------------------

commit 415ba26c upstream.

Sink only devices do not have any source capabilities, so
the driver should not warn about that. Also DRP (Dual Role
Power) capable devices, such as USB Type-C docking stations,
do not return any source capabilities unless they are
plugged to a power supply themselves.

Fixes: 1f4642b7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4")
Reported-by: NPaul Menzel <pmenzel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922145924.80667-1-heikki.krogerus@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.147
commit e5ee7b77ac9b1fe459eba7a389b80b1feb527334
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0W8

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=e5ee7b77ac9b1fe459eba7a389b80b1feb527334

--------------------------------

commit 0fb9703a upstream.

The UAS mode of Thinkplus(0x17ef, 0x3899) is reported to influence
performance and trigger kernel panic on several platforms with the
following error message:

[   39.702439] xhci_hcd 0000:0c:00.3: ERROR Transfer event for disabled
               endpoint or incorrect stream ring
[   39.702442] xhci_hcd 0000:0c:00.3: @000000026c61f810 00000000 00000000
               1b000000 05038000

[  720.545894][13] Workqueue: usb_hub_wq hub_event
[  720.550971][13]  ffff88026c143c38 0000000000016300 ffff8802755bb900 ffff880
                    26cb80000
[  720.559673][13]  ffff88026c144000 ffff88026ca88100 0000000000000000 ffff880
                    26cb80000
[  720.568374][13]  ffff88026cb80000 ffff88026c143c50 ffffffff8186ae25 ffff880
                    26ca880f8
[  720.577076][13] Call Trace:
[  720.580201][13]  [<ffffffff8186ae25>] schedule+0x35/0x80
[  720.586137][13]  [<ffffffff8186b0ce>] schedule_preempt_disabled+0xe/0x10
[  720.593623][13]  [<ffffffff8186cb94>] __mutex_lock_slowpath+0x164/0x1e0
[  720.601012][13]  [<ffffffff8186cc3f>] mutex_lock+0x2f/0x40
[  720.607141][13]  [<ffffffff8162b8e9>] usb_disconnect+0x59/0x290

Falling back to USB mass storage can solve this problem, so ignore UAS
function of this chip.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NHongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663902249837086.19.seg@mailgwSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.147
commit 5f91ceea6c146ea78c25a45fefa0b361410b1f99
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0W8

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=5f91ceea6c146ea78c25a45fefa0b361410b1f99

--------------------------------

commit e00b488e upstream.

The UAS mode of Hiksemi USB_HDD is reported to fail to work on several
platforms with the following error message, then after re-connecting the
device will be offlined and not working at all.

[  592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
                   inflight: CMD
[  592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
                   04 00 00
[  592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
                   inflight: CMD
[  592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
                   00 08 00

These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NHongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901185-21067-1-git-send-email-zenghongling@kylinos.cnSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.147
commit 1e4b856fc0bba4cebea5a7ab3ed2de52bcaf91cb
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0W8

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=1e4b856fc0bba4cebea5a7ab3ed2de52bcaf91cb

--------------------------------

commit a625a4b8 upstream.

The UAS mode of Hiksemi is reported to fail to work on several platforms
with the following error message, then after re-connecting the device will
be offlined and not working at all.

[  592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
                   inflight: CMD
[  592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
                   04 00 00
[  592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
                   inflight: CMD
[  592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
                   00 08 00

These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NHongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901173-21020-1-git-send-email-zenghongling@kylinos.cnSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit f31ea57c1183415b7069853a8a57ec9288dc4aef
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=f31ea57c1183415b7069853a8a57ec9288dc4aef

--------------------------------

commit de5107f4 upstream.

Bus bandwidth array access is based on esit, increase one
will cause out-of-bounds issue; for example, when esit is
XHCI_MTK_MAX_ESIT, will overstep boundary.

Fixes: 7c986fbc ("usb: xhci-mtk: get the microframe boundary for ESIT")
Cc: <stable@vger.kernel.org>
Reported-by: NStan Lu <stan.lu@mediatek.com>
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1629189389-18779-5-git-send-email-chunfeng.yun@mediatek.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit a1926f11d9aa69ecca29cde7958d9a6dbdccc4aa
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=a1926f11d9aa69ecca29cde7958d9a6dbdccc4aa

--------------------------------

commit d640c4cb upstream.

add support for Quectel RM520N which is based on Qualcomm SDX62 chip.

0x0801: DIAG + NMEA + AT + MODEM + RMNET

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 10 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0801 Rev= 5.04
S:  Manufacturer=Quectel
S:  Product=RM520N-GL
S:  SerialNumber=384af524
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Njerry meng <jerry-meng@foxmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit 4d1d91a6343ee000c16778a8f28d9ad2b8116d39
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=4d1d91a6343ee000c16778a8f28d9ad2b8116d39

--------------------------------

commit f8f67eff upstream.

Add support for the following Quectel BG95 composition:

0x0203: Diag + GNSS + Modem + ECM

usb-devices output:
T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=0203 Rev= 0.00
S:  Manufacturer=Quectel, Incorporated
S:  Product=Quectel LPWA Module
S:  SerialNumber=71d3a21b
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=85(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
I:  If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: NCarl Yin <carl.yin@quectel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit 561d86bd0e288ad236e4f208ce2ae418a6e0e431
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=561d86bd0e288ad236e4f208ce2ae418a6e0e431

--------------------------------

[ Upstream commit fe0a2ac7 ]

This reverts commit 8cb339f1 as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: Nkernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit c4adbfa9cea72ab192c68043ebc0b8203d5ada27
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=c4adbfa9cea72ab192c68043ebc0b8203d5ada27

--------------------------------

[ Upstream commit 58bfe7d8 ]

This reverts commit 3d5f7094.

The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: NOliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f7094 ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit 905e8be5284b09e69cb16a384f796c61a54c0bb1
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=905e8be5284b09e69cb16a384f796c61a54c0bb1

--------------------------------

[ Upstream commit b46a6b09 ]

ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.

Fixes: 7733f6c3 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: NPeter Chen <peter.chen@kernel.org>
Signed-off-by: NPawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit 8fcb5f027b3967cba11f941c459f9834ea3a7a35
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=8fcb5f027b3967cba11f941c459f9834ea3a7a35

--------------------------------

[ Upstream commit d5dcc336 ]

The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.

Fixes: 249f0a25 ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: NPeter Chen <peter.chen@kernel.org>
Signed-off-by: NPawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit f457bb21984b9e412a7bb56ea74482da621e6046
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=f457bb21984b9e412a7bb56ea74482da621e6046

--------------------------------

[ Upstream commit 8cb339f1 ]

For ARM processor, unaligned access to device memory is not allowed.
Method memcpy does not take care of alignment.

USB detection failure with the unaligned address of memory access, with
below kernel crash. To fix the unaligned address the kernel panic issue,
replace memcpy with memcpy_toio method.

Kernel crash:
Unable to handle kernel paging request at virtual address ffff80000c05008a
Mem abort info:
  ESR = 0x96000061
  EC = 0x25: DABT (current EL), IL = 32 bits
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
  FSC = 0x21: alignment fault
Data abort info:
  ISV = 0, ISS = 0x00000061
  CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000
[ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003,
pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713
Internal error: Oops: 96000061 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x30/0x260
lr : __xudc_ep0_queue+0xf0/0x110
sp : ffff800008003d00
x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0
x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080
x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080
x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000
x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000
x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200
x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0
x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112
x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80
x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088
Call trace:
 __memcpy+0x30/0x260
 xudc_ep0_queue+0x3c/0x60
 usb_ep_queue+0x38/0x44
 composite_ep0_queue.constprop.0+0x2c/0xc0
 composite_setup+0x8d0/0x185c
 configfs_composite_setup+0x74/0xb0
 xudc_irq+0x570/0xa40
 __handle_irq_event_percpu+0x58/0x170
 handle_irq_event+0x60/0x120
 handle_fasteoi_irq+0xc0/0x220
 handle_domain_irq+0x60/0x90
 gic_handle_irq+0x74/0xa0
 call_on_irq_stack+0x2c/0x60
 do_interrupt_handler+0x54/0x60
 el1_interrupt+0x30/0x50
 el1h_64_irq_handler+0x18/0x24
 el1h_64_irq+0x78/0x7c
 arch_cpu_idle+0x18/0x2c
 do_idle+0xdc/0x15c
 cpu_startup_entry+0x28/0x60
 rest_init+0xc8/0xe0
 arch_call_rest_init+0x10/0x1c
 start_kernel+0x694/0x6d4
 __primary_switched+0xa4/0xac

Fixes: 1f7c5166 ("usb: gadget: Add xilinx usb2 device support")
Cc: stable@vger.kernel.org
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NPiyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220824071253.1261096-1-piyush.mehta@amd.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.150
commit b239a0993aa2d603c11bd94fa4a93670fb117d45
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b239a0993aa2d603c11bd94fa4a93670fb117d45

--------------------------------

[ Upstream commit 3d5f7094 ]

The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream

Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:

  Timeout while waiting for setup device command
  device not accepting address X, error -62
  unable to enumerate USB device

By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.
Signed-off-by: NJean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220824191320.17883-1-jflf_kernel@gmx.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>

stable inclusion
from stable-v5.10.146
commit 7780b3dda212babc7b8988c9f8f82f5324e8f7cf
category: bugfix
bugzilla: https://gitee.com/openeuler/kernel/issues/I6D0VX

Reference: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=7780b3dda212babc7b8988c9f8f82f5324e8f7cf

--------------------------------

[ Upstream commit 54801195 ]

Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.

This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.

Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
Signed-off-by: NIkjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133937.1.Ia8174b875bc926c12ce427a5a1415dea31cc35ae@changeidSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NJialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: NZheng Zengkai <zhengzengkai@huawei.com>