Pull arm-soc power management changes from Olof Johansson:
 "Power management changes here are mostly for the omap platform, but
  also include cpuidle changes for ux500 and suspend/resume code for
  mmp."

* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  ARM: OMAP2+: WDTIMER integration: fix !PM boot crash, disarm timer after hwmod reset
  ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod database
  ARM: OMAP4: hwmod_data: Name the common irq for McBSP ports
  ARM: OMAP4: hwmod data: I2C: add flag for context restore
  ARM: OMAP3: hwmod_data: Rename the common irq for McBSP ports
  ARM: OMAP2xxx: hwmod data: add HDQ/1-wire hwmod
  ARM: OMAP3: hwmod data: add HDQ/1-wire hwmod
  ARM: OMAP2+: hwmod data: add HDQ/1-wire hwmod shared data
  ARM: OMAP2+: HDQ1W: add custom reset function
  ARM: OMAP2420: hwmod data: Add MMC hwmod data for 2420
  arm: omap3: clockdomain data: Remove superfluous commas from gfx_sgx_3xxx_wkdeps[]
  ARM: OMAP2+: powerdomain: Get rid off duplicate pwrdm_clkdm_state_switch() API
  ARM: OMAP3: clock data: add clockdomain for HDQ functional clock
  ARM: OMAP3+: dpll: Configure autoidle mode only if it's supported
  ARM: OMAP2+: dmtimer: cleanup iclk usage
  ARM: OMAP4+: Add prm and cm base init function.
  ARM: OMAP2/3: Add idle_st bits for ST_32KSYNC timer to prcm-common header
  ARM: OMAP3: Fix CM register bit masks
  ARM: OMAP: clock: convert AM3517/3505 detection/flags to AM35xx
  ARM: OMAP3: clock data: treat all AM35x devices the same
  ...

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...

Pull support for new arm SoCs from Olof Johansson:
 "Three new system-on-chip models are supported: the st-ericsson u9540
  in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.

  Emma is a little bit special because it is completely unrelated to the
  classic shmobile models, but the new Renesas rmobile SoCs are a
  combination of things from both Emma and shmobile, so it was decided
  to have them all live in one directory.

  This also contains updates to existing shmobile soc code as well as
  some related board changes due to dependencies."

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  mach-shmobile: Use DT_MACHINE for KZM9D V3
  mach-shmobile: Emma Mobile EV2 DT support V3
  mach-shmobile: KZM9D board Ethernet support V3
  mach-shmobile: Emma Mobile EV2 GPIO support V3
  mach-shmobile: Emma Mobile EV2 SMP support V3
  mach-shmobile: KZM9D board support V3
  mach-shmobile: Emma Mobile EV2 SoC base support V3
  gpio: Emma Mobile GPIO driver V2
  ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
  ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
  ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
  ARM: mach-shmobile: clock-r8a7740: add SDHI clock
  ARM: mach-shmobile: clock-r8a7740: add USB clock
  ARM: mach-shmobile: clock-r8a7740: add FSI clock
  ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
  ARM: mach-shmobile: r8a7740: add gpio_irq support
  ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
  ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
  ARM: ux500: ioremap differences for DB9540
  ARM: ux500: core U9540 support
  ...

Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
 "The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
  of booting using device trees, which is a great step forward for them.
  at91 and spear have pretty much completed this process with a huge
  amount of work being put into at91.  The other platforms are
  continuing the process.

  We finally start to see the payback on this investment, as new
  machines are getting supported purely by adding a .dts source file
  that can be completely independent of the kernel source."

Fix up trivial conflict in arch/arm/Kconfig

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
  ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
  arm/dts: omap4-panda: Add LEDs support
  arm/dts: omap4-sdp: Add LEDs support
  arm/dts: twl4030: Add twl4030-gpio node
  OMAP4: devices: Do not create mcpdm device if the dtb has been provided
  OMAP4: devices: Do not create dmic device if the dtb has been provided
  Documentation: update docs for mmp dt
  ARM: dts: refresh dts file for arch mmp
  ARM: mmp: support pxa910 with device tree
  ARM: mmp: support mmp2 with device tree
  gpio: pxa: parse gpio from DTS file
  ARM: mmp: support DT in timer
  ARM: mmp: support DT in irq
  ARM: mmp: append CONFIG_MACH_MMP2_DT
  ARM: mmp: fix build issue on mmp with device tree
  ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
  ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
  ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
  ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
  ARM: SPEAr3xx: Correct keyboard data passed from DT
  ...

Pull non-critical arm-soc bug fixes from Olof Johansson:
 "These bug fixes were not important enough to have them included in the
  v3.4 release, mostly because they cover harmless warnings or
  unrealistic configurations.  Instead we queue them up to be picked up
  in the next merge window."

Fixed up trivial conflict in arch/arm/mach-omap2/board-omap4panda.c

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: spear6xx: remove board selection options
  ARM: OMAP: igep0020: Specify the VPLL2 regulator unconditionally
  ARM: OMAP2+: INTC: fix Kconfig option for TI81XX
  ARM: OMAP2+: remove incorrect irq_chip ack field
  ARM: OMAP4: Adding ID for OMAP4460 ES1.1
  ARM: OMAP4: panda: add statics to remove warnings
  ARM: OMAP2+: Incorrect Register Offsets in OMAP Mailbox
  ARM: OMAP: fix trivial warnings for dspbridge
  arm: davinci: use for_each_set_bit_from
  ARM: OMAP4: hsmmc: check for null pointer
  ARM: OMAP1: fix compilation issue in board-sx1.c
  ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
  ARM: davinci: da850-evm: fix section mismatch
  ARM: tegra: add pll_x freq table entry for 750MHz
  ARM: davinci: mark spi_board_info arguments as const
  ARM: davinci: fix incorrect pdctl next bit position

Pull first batch of arm-soc cleanups from Olof Johansson:
 "These cleanups are basically all over the place.  The idea is to
  collect changes with minimal impact but large number of changes so we
  can avoid them from distracting in the diffstat in the other series.

  A significant number of lines get removed here, in particular because
  the ixp2000 and ixp23xx platforms get removed.  These have never been
  extremely popular and have fallen into disuse over time with no active
  maintainer taking care of them.  The u5500 soc never made it into a
  product, so we are removing it from the ux500 platform.

  Many good cleanups also went into the at91 and omap platforms, as has
  been the case for a number of releases."

Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
  ARM: clps711x: Cleanup IRQ handling
  ARM clps711x: Removed unused header mach/time.h
  ARM: clps711x: Added note about support EP731x CPU to Kconfig
  ARM: clps711x: Added missing register definitions
  ARM: clps711x: Used own subarch directory for store header file
  Dove: Fix Section mismatch warnings
  ARM: orion5x: ts78xx debugging changes
  ARM: orion5x: remove PM dependency from ts78xx
  ARM: orion5x: ts78xx fix NAND resource off by one
  ARM: orion5x: ts78xx whitespace cleanups
  Orion5x: Fix Section mismatch warnings
  Orion5x: Fix warning: struct pci_dev declared inside paramter list
  ARM: clps711x: Combine header files into one for clps711x-targets
  ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
  ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
  ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
  ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
  ARM: S5PV210: Use common macro to define resources on dev-audio.c
  ARM: S5PC100: Use common macro to define resources on dev-audio.c
  ARM: S5P64X0: Use common macro to define resources on dev-audio.c
  ...

Pull arm-soc updates for MAINTAINERS file from Olof Johansson:
 "This is a collection of updates to the MAINTAINERS file, separated out
  mostly to give an overview of what has changed regarding who does what.

  In particular, at91, orion and prima2 platforms and drivers are
  updated in this batch."

* tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINER: add some drivers upstreamed in CSR SIRFPRIMA2
  maintainership update for the Marvell Orion family of SOCs
  MAINTAINERS: remove non-responding web link for atmel_usba driver
  MAINTAINERS: add entry for Atmel timer counter (TC)
  MAINTAINERS: add entry for Atmel DMA driver
  MAINTAINERS: add entry for Atmel touch screen ADC controller driver
  MAINTAINERS: add entry for Atmel isi driver

Pull ktest updates from Steven Rostedt.

* tag 'ktest-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Add README to explain what is in the examples directory
  ktest: Add the snowball.conf example config
  ktest: Add an example config that does cross compiling of several archs
  ktest: Add kvm.conf example config
  ktest: Add useful example configs
  ktest: Add USE_OUTPUT_MIN_CONFIG to avoid prompt on make_min_config
  ktest: Add MIN_CONFIG_TYPE to allow making a minum .config that has network
  ktest: Fix kernelrevision with POST_BUILD

Add a README that explains what the different example configs in the
ktest example directory are about.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

I used the snowball.conf in a live demo that demonstrated how to use
ktest.pl with a snowball ARM board. I've been asked to included that
config in the ktest repository.

Here it is.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Add the config that I use to test several archs. I downloaded several
cross compilers from:

 http://kernel.org/pub/tools/crosstool/files/bin/x86_64/

and this config is an example to crosscompile several archs to make sure
that your changes do not break archs that you are not working on.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Add an example config that explains how to use ktest with a virtual
guest as the target.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

I've been asked several times to provide more useful example configs for
ktest.pl, as the sample.conf is too complex (because it explains all
configs). This adds configs broken up by use case, and these configs are
based on actual configs that I use on a daily basis.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

If the file that OUTPUT_MIN_CONFIG exists then ktest.pl will prompt the
user and ask them if the OUTPUT_MIN_CONFIG should be used as the
starting point for make_min_config instead of MIN_CONFIG.

This is usually the case, and to allow the user to do so, which is
helpful if the user is creating different min configs based on tests,
and they know one is a superset of another test, they can set
USE_OUTPUT_MIN_CONFIG to one, which will prevent kest.pl from prompting
to use the OUTPUT_MIN_CONFIG and it will just use it.

If USE_OUTPUT_MIN_CONIFG is set to zero, then ktest.pl will continue to
use MIN_CONFIG instead.

The default is that USE_OUTPUT_MIN_CONFIG is undefined.
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

When using the MERAM the LCDC line size needs to be programmed with a
MERAM-specific value different than the real frame buffer pitch. Fix it.
Reported-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org  # for 3.4
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull core irq changes from Ingo Molnar:
 "A collection of small fixes."

By Thomas Gleixner
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  hexagon: Remove select of not longer existing Kconfig switches
  arm: Select core options instead of redefining them
  genirq: Do not consider disabled wakeup irqs
  genirq: Allow check_wakeup_irqs to notice level-triggered interrupts
  genirq: Be more informative on irq type mismatch
  genirq: Reject bogus threaded irq requests
  genirq: Streamline irq_action

Pull security subsystem updates from James Morris:
 "New notable features:
   - The seccomp work from Will Drewry
   - PR_{GET,SET}_NO_NEW_PRIVS from Andy Lutomirski
   - Longer security labels for Smack from Casey Schaufler
   - Additional ptrace restriction modes for Yama by Kees Cook"

Fix up trivial context conflicts in arch/x86/Kconfig and include/linux/filter.h

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (65 commits)
  apparmor: fix long path failure due to disconnected path
  apparmor: fix profile lookup for unconfined
  ima: fix filename hint to reflect script interpreter name
  KEYS: Don't check for NULL key pointer in key_validate()
  Smack: allow for significantly longer Smack labels v4
  gfp flags for security_inode_alloc()?
  Smack: recursive tramsmute
  Yama: replace capable() with ns_capable()
  TOMOYO: Accept manager programs which do not start with / .
  KEYS: Add invalidation support
  KEYS: Do LRU discard in full keyrings
  KEYS: Permit in-place link replacement in keyring list
  KEYS: Perform RCU synchronisation on keys prior to key destruction
  KEYS: Announce key type (un)registration
  KEYS: Reorganise keys Makefile
  KEYS: Move the key config into security/keys/Kconfig
  KEYS: Use the compat keyctl() syscall wrapper on Sparc64 for Sparc32 compat
  Yama: remove an unused variable
  samples/seccomp: fix dependencies on arch macros
  Yama: add additional ptrace scopes
  ...

Merge tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus

Pull virtio updates from Rusty Russell.

* tag 'virtio-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  virtio: fix typo in comment
  virtio-mmio: Devices parameter parsing
  virtio_blk: Drop unused request tracking list
  virtio-blk: Fix hot-unplug race in remove method
  virtio: Use ida to allocate virtio index
  virtio: balloon: separate out common code between remove and freeze functions
  virtio: balloon: drop restore_common()
  9p: disconnect channel when PCI device is removed
  virtio: update documentation to v0.9.5 of spec

- Delete "@request_vqs" and "@free_vqs" comments, since
  they are no longer in struct virtio_config_ops.
- According to the macro below, "@val" should be "@v".
Signed-off-by: NChen Baozi <chenbaozi@gmail.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

This patch adds an option to instantiate guest virtio-mmio devices
basing on a kernel command line (or module) parameter, for example:

	virtio_mmio.devices=0x100@0x100b0000:48
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Benchmark shows small performance improvement on fusion io device.

Before:
  seq-read : io=1,024MB, bw=19,982KB/s, iops=39,964, runt= 52475msec
  seq-write: io=1,024MB, bw=20,321KB/s, iops=40,641, runt= 51601msec
  rnd-read : io=1,024MB, bw=15,404KB/s, iops=30,808, runt= 68070msec
  rnd-write: io=1,024MB, bw=14,776KB/s, iops=29,552, runt= 70963msec

After:
  seq-read : io=1,024MB, bw=20,343KB/s, iops=40,685, runt= 51546msec
  seq-write: io=1,024MB, bw=20,803KB/s, iops=41,606, runt= 50404msec
  rnd-read : io=1,024MB, bw=16,221KB/s, iops=32,442, runt= 64642msec
  rnd-write: io=1,024MB, bw=15,199KB/s, iops=30,397, runt= 68991msec
Signed-off-by: NAsias He <asias@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

If we reset the virtio-blk device before the requests already dispatched
to the virtio-blk driver from the block layer are finised, we will stuck
in blk_cleanup_queue() and the remove will fail.

blk_cleanup_queue() calls blk_drain_queue() to drain all requests queued
before DEAD marking. However it will never success if the device is
already stopped. We'll have q->in_flight[] > 0, so the drain will not
finish.

How to reproduce the race:
1. hot-plug a virtio-blk device
2. keep reading/writing the device in guest
3. hot-unplug while the device is busy serving I/O

Test:
~1000 rounds of hot-plug/hot-unplug test passed with this patch.

Changes in v3:
- Drop blk_abort_queue and blk_abort_request
- Use __blk_end_request_all to complete request dispatched to driver

Changes in v2:
- Drop req_in_flight
- Use virtqueue_detach_unused_buf to get request dispatched to driver
Signed-off-by: NAsias He <asias@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Current index allocation in virtio is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. E.g. someone crazy doing this in host side.

while(1) {
	hot-plug a virtio device
	hot-unplug the virito devcie
}
Signed-off-by: NAsias He <asias@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

The remove and freeze functions have a lot of shared code; put it into a
common function that gets called by both.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

restore_common() was used when there were different thaw and freeze PM
callbacks implemented.  We removed thaw in commit
f38f8387.

restore_common() can be removed and virtballoon_restore() can itself do
the restore ops.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

When a virtio_9p pci device is being removed, we should close down any
active channels and free up resources, we're not supposed to BUG() if there's
still an open channel since it's a valid case when removing the PCI device.

Otherwise, removing the PCI device with an open channel would cause the
following BUG():

[ 1184.671416] ------------[ cut here ]------------
[ 1184.672057] kernel BUG at net/9p/trans_virtio.c:618!
[ 1184.672057] invalid opcode: 0000 [#1] PREEMPT SMP
[ 1184.672057] CPU 3
[ 1184.672057] Pid: 5, comm: kworker/u:0 Tainted: G        W    3.4.0-rc2-next-20120413-sasha-dirty #76
[ 1184.672057] RIP: 0010:[<ffffffff825c9116>]  [<ffffffff825c9116>] p9_virtio_remove+0x16/0x90
[ 1184.672057] RSP: 0018:ffff88000d653ac0  EFLAGS: 00010202
[ 1184.672057] RAX: ffffffff836bfb40 RBX: ffff88000c9b2148 RCX: ffff88000d658978
[ 1184.672057] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff880028868000
[ 1184.672057] RBP: ffff88000d653ad0 R08: 0000000000000000 R09: 0000000000000000
[ 1184.672057] R10: 0000000000000000 R11: 0000000000000001 R12: ffff880028868000
[ 1184.672057] R13: ffffffff835aa7c0 R14: ffff880041630000 R15: ffff88000d653da0
[ 1184.672057] FS:  0000000000000000(0000) GS:ffff880035a00000(0000) knlGS:0000000000000000
[ 1184.672057] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1184.672057] CR2: 0000000001181000 CR3: 000000000eba1000 CR4: 00000000000406e0
[ 1184.672057] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
x000000000117a190 *[ 1184.672057] DR3: 00000000000000**
00 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 1184.672057] Process kworker/u:0 (pid: 5, threadinfo ffff88000d652000, task ffff88000d658000)
[ 1184.672057] Stack:
[ 1184.672057]  ffff880028868000 ffffffff836bfb40 ffff88000d653af0 ffffffff8193661b
[ 1184.672057]  ffff880028868008 ffffffff836bfb40 ffff88000d653b10 ffffffff81af1c81
[ 1184.672057]  ffff880028868068 ffff880028868008 ffff88000d653b30 ffffffff81af257a
[ 1184.795301] Call Trace:
[ 1184.795301]  [<ffffffff8193661b>] virtio_dev_remove+0x1b/0x60
[ 1184.795301]  [<ffffffff81af1c81>] __device_release_driver+0x81/0xd0
[ 1184.795301]  [<ffffffff81af257a>] device_release_driver+0x2a/0x40
[ 1184.795301]  [<ffffffff81af0d48>] bus_remove_device+0x138/0x150
[ 1184.795301]  [<ffffffff81aef08d>] device_del+0x14d/0x1b0
[ 1184.795301]  [<ffffffff81aef138>] device_unregister+0x48/0x60
[ 1184.795301]  [<ffffffff8193694d>] unregister_virtio_device+0xd/0x10
[ 1184.795301]  [<ffffffff8265fc74>] virtio_pci_remove+0x2a/0x6c
[ 1184.795301]  [<ffffffff818a95ad>] pci_device_remove+0x4d/0x110
[ 1184.795301]  [<ffffffff81af1c81>] __device_release_driver+0x81/0xd0
[ 1184.795301]  [<ffffffff81af257a>] device_release_driver+0x2a/0x40
[ 1184.795301]  [<ffffffff81af0d48>] bus_remove_device+0x138/0x150
[ 1184.795301]  [<ffffffff81aef08d>] device_del+0x14d/0x1b0
[ 1184.795301]  [<ffffffff81aef138>] device_unregister+0x48/0x60
[ 1184.795301]  [<ffffffff818a36fa>] pci_stop_bus_device+0x6a/0x90
[ 1184.795301]  [<ffffffff818a3791>] pci_stop_and_remove_bus_device+0x11/0x20
[ 1184.795301]  [<ffffffff818c21d9>] remove_callback+0x9/0x10
[ 1184.795301]  [<ffffffff81252d91>] sysfs_schedule_callback_work+0x21/0x60
[ 1184.795301]  [<ffffffff810cb1a1>] process_one_work+0x281/0x430
[ 1184.795301]  [<ffffffff810cb140>] ? process_one_work+0x220/0x430
[ 1184.795301]  [<ffffffff81252d70>] ? sysfs_read_file+0x1c0/0x1c0
[ 1184.795301]  [<ffffffff810cc613>] worker_thread+0x1f3/0x320
[ 1184.795301]  [<ffffffff810cc420>] ? manage_workers.clone.13+0x130/0x130
[ 1184.795301]  [<ffffffff810d30b2>] kthread+0xb2/0xc0
[ 1184.795301]  [<ffffffff826783f4>] kernel_thread_helper+0x4/0x10
[ 1184.795301]  [<ffffffff810deb18>] ? finish_task_switch+0x78/0xf0
[ 1184.795301]  [<ffffffff82676574>] ? retint_restore_args+0x13/0x13
[ 1184.795301]  [<ffffffff810d3000>] ? kthread_flush_work_fn+0x10/0x10
[ 1184.795301]  [<ffffffff826783f0>] ? gs_change+0x13/0x13
[ 1184.795301] Code: c1 9e 0a 00 48 83 c4 08 5b c9 c3 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 41 54 49 89 fc 53 48 8b 9f a8 04 00 00 80 3b 00 74 0a <0f> 0b 0f 1f 84 00 00 00 00 00 48 8b 87 88 04 00 00 ff 50 30 31
[ 1184.795301] RIP  [<ffffffff825c9116>] p9_virtio_remove+0x16/0x90
[ 1184.795301]  RSP <ffff88000d653ac0>
[ 1184.952618] ---[ end trace a307b3ed40206b4c ]---
Signed-off-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Pull smp hotplug cleanups from Thomas Gleixner:
 "This series is merily a cleanup of code copied around in arch/* and
  not changing any of the real cpu hotplug horrors yet.  I wish I'd had
  something more substantial for 3.5, but I underestimated the lurking
  horror..."

Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h

* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
  um: Remove leftover declaration of alloc_task_struct_node()
  task_allocator: Use config switches instead of magic defines
  sparc: Use common threadinfo allocator
  score: Use common threadinfo allocator
  sh-use-common-threadinfo-allocator
  mn10300: Use common threadinfo allocator
  powerpc: Use common threadinfo allocator
  mips: Use common threadinfo allocator
  hexagon: Use common threadinfo allocator
  m32r: Use common threadinfo allocator
  frv: Use common threadinfo allocator
  cris: Use common threadinfo allocator
  x86: Use common threadinfo allocator
  c6x: Use common threadinfo allocator
  fork: Provide kmemcache based thread_info allocator
  tile: Use common threadinfo allocator
  fork: Provide weak arch_release_[task_struct|thread_info] functions
  fork: Move thread info gfp flags to header
  fork: Remove the weak insanity
  sh: Remove cpu_idle_wait()
  ...

Pull RCU changes from Ingo Molnar:
 "This is the v3.5 RCU tree from Paul E.  McKenney:

 1) A set of improvements and fixes to the RCU_FAST_NO_HZ feature (with
    more on the way for 3.6).  Posted to LKML:
       https://lkml.org/lkml/2012/4/23/324 (commits 1-3 and 5),
       https://lkml.org/lkml/2012/4/16/611 (commit 4),
       https://lkml.org/lkml/2012/4/30/390 (commit 6), and
       https://lkml.org/lkml/2012/5/4/410 (commit 7, combined with
       the other commits for the convenience of the tester).

 2) Changes to make rcu_barrier() avoid disrupting execution of CPUs
    that have no RCU callbacks.  Posted to LKML:
       https://lkml.org/lkml/2012/4/23/322.

 3) A couple of commits that improve the efficiency of the interaction
    between preemptible RCU and the scheduler, these two being all that
    survived an abortive attempt to allow preemptible RCU's
    __rcu_read_lock() to be inlined.  The full set was posted to LKML at
    https://lkml.org/lkml/2012/4/14/143, and the first and third patches
    of that set remain.

 4) Lai Jiangshan's algorithmic implementation of SRCU, which includes
    call_srcu() and srcu_barrier().  A major feature of this new
    implementation is that synchronize_srcu() no longer disturbs the
    execution of other CPUs.  This work is based on earlier
    implementations by Peter Zijlstra and Paul E.  McKenney.  Posted to
    LKML: https://lkml.org/lkml/2012/2/22/82.

 5) A number of miscellaneous bug fixes and improvements which were
    posted to LKML at: https://lkml.org/lkml/2012/4/23/353 with
    subsequent updates posted to LKML."

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  rcu: Make rcu_barrier() less disruptive
  rcu: Explicitly initialize RCU_FAST_NO_HZ per-CPU variables
  rcu: Make RCU_FAST_NO_HZ handle timer migration
  rcu: Update RCU maintainership
  rcu: Make exit_rcu() more precise and consolidate
  rcu: Move PREEMPT_RCU preemption to switch_to() invocation
  rcu: Ensure that RCU_FAST_NO_HZ timers expire on correct CPU
  rcu: Add rcutorture test for call_srcu()
  rcu: Implement per-domain single-threaded call_srcu() state machine
  rcu: Use single value to handle expedited SRCU grace periods
  rcu: Improve srcu_readers_active_idx()'s cache locality
  rcu: Remove unused srcu_barrier()
  rcu: Implement a variant of Peter's SRCU algorithm
  rcu: Improve SRCU's wait_idx() comments
  rcu: Flip ->completed only once per SRCU grace period
  rcu: Increment upper bit only for srcu_read_lock()
  rcu: Remove fast check path from __synchronize_srcu()
  rcu: Direct algorithmic SRCU implementation
  rcu: Introduce rcutorture testing for rcu_barrier()
  timer: Fix mod_timer_pinned() header comment
  ...

Pull core locking updates from Ingo Molnar:
 "This update:

   - extends and simplifies x86 NMI callback handling code to enhance
     and fix the HP hw-watchdog driver

   - simplifies the x86 NMI callback handling code to fix a kmemcheck
     bug.

   - enhances the hung-task debugger"

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi: Fix the type of the nmiaction.flags field
  x86/nmi: Fix page faults by nmiaction if kmemcheck is enabled
  x86/nmi: Add new NMI queues to deal with IO_CHK and SERR
  watchdog, hpwdt: Remove priority option for NMI callback
  hung task debugging: Inject NMI when hung and going to panic

Pull iommu core changes from Ingo Molnar:
 "The IOMMU changes in this cycle are mostly about factoring out
  Intel-VT-d specific IRQ remapping details and introducing struct
  irq_remap_ops, in preparation for AMD specific hardware."

* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  iommu: Fix off by one in dmar_get_fault_reason()
  irq_remap: Fix the 'sub_handle' uninitialized warning
  irq_remap: Fix UP build failure
  irq_remap: Fix compiler warning with CONFIG_IRQ_REMAP=y
  iommu: rename intr_remapping.[ch] to irq_remapping.[ch]
  iommu: rename intr_remapping references to irq_remapping
  x86, iommu/vt-d: Clean up interfaces for interrupt remapping
  iommu/vt-d: Convert MSI remapping setup to remap_ops
  iommu/vt-d: Convert free_irte into a remap_ops callback
  iommu/vt-d: Convert IR set_affinity function to remap_ops
  iommu/vt-d: Convert IR ioapic-setup to use remap_ops
  iommu/vt-d: Convert missing apic.c intr-remapping call to remap_ops
  iommu/vt-d: Make intr-remapping initialization generic
  iommu: Rename intr_remapping files to intel_intr_remapping

Pull core/debugobjects changes from Ingo Molnar:
 "Not much happened: it includes a cleanup and an irq latency reduction
  fixlet."

* 'core-debugobjects-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  debugobjects: Fill_pool() returns void now
  debugobjects: printk with irqs enabled
  debugobjects: Remove unused return value from fill_pool()

Pull GFS2 changes from Steven Whitehouse.

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw: (24 commits)
  GFS2: Fix quota adjustment return code
  GFS2: Add rgrp information to block_alloc trace point
  GFS2: Eliminate unused "new" parameter to gfs2_meta_indirect_buffer
  GFS2: Update glock doc to add new stats info
  GFS2: Update main gfs2 doc
  GFS2: Remove redundant metadata block type check
  GFS2: Fix sgid propagation when using ACLs
  GFS2: eliminate log elements and simplify
  GFS2: Eliminate vestigial sd_log_le_rg
  GFS2: Eliminate needless parameter from function gfs2_setbit
  GFS2: Log code fixes
  GFS2: Remove unused argument from gfs2_internal_read
  GFS2: Remove bd_list_tr
  GFS2: Remove duplicate log code
  GFS2: Clean up log write code path
  GFS2: Use variable rather than qa to determine if unstuff necessary
  GFS2: Change variable blk to biblk
  GFS2: Fix function parameter comments in rgrp.c
  GFS2: Eliminate offset parameter to gfs2_setbit
  GFS2: Use slab for block reservation memory
  ...

Pull m68knommu tree from Greg Ungerer:
 "More merge and clean up of MMU and non-MMU common files, namely
  signal.c and dma.c.  There is also a simplification of the ColdFire
  GPIO setup tables.  Using a couple of simple macros we make the init
  tables really small and easy to read, and save a couple of thousand
  lines of code.  Also a move of all the ColdFire subarch support files
  into the existing coldfire directory.  The sub-directories just ended
  up duplicating Makefiles and now only contain really simple pieces of
  code.  This saves quite a few lines of code too.

  As always a couple of bugs fixes thrown in too.  Oh and a new
  defconfig for the ColdFire platforms that support having the MMU
  enabled."

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (39 commits)
  m68k: add a defconfig for the M5475EVB ColdFire with MMU board
  m68knommu: unaligned.h fix for M68000 core
  m68k: merge the MMU and non-MMU versions of the arch dma code
  m68knommu: reorganize the no-MMU cache flushing to match m68k
  m68knommu: move the 54xx platform code into the common ColdFire code directory
  m68knommu: move the 532x platform code into the common ColdFire code directory
  m68knommu: move the 5407 platform code into the common ColdFire code directory
  m68knommu: move the 5307 platform code into the common ColdFire code directory
  m68knommu: move the 528x platform code into the common ColdFire code directory
  m68knommu: move the 527x platform code into the common ColdFire code directory
  m68knommu: move the 5272 platform code into the common ColdFire code directory
  m68knommu: move the 5249 platform code into the common ColdFire code directory
  m68knommu: move the 523x platform code into the common ColdFire code directory
  m68knommu: move the 520x platform code into the common ColdFire code directory
  m68knommu: move the 5206 platform code into the common ColdFire code directory
  m68knommu: simplify the ColdFire 5407 GPIO struct setup
  m68knommu: simplify the ColdFire 532x GPIO struct setup
  m68knommu: simplify the ColdFire 5307 GPIO struct setup
  m68knommu: simplify the ColdFire 528x GPIO struct setup
  m68knommu: simplify the ColdFire 527x GPIO struct setup
  ...

This reverts commit 8c01a529.

It turns out the d_unhashed() check isn't unnecessary after all: while
it's true that unhashing will increment the sequence numbers, that does
not necessarily invalidate the RCU lookup, because it might have seen
the dentry pointer (before it got unhashed), but by the time it loaded
the sequence number, it could have seen the *new* sequence number (after
it got unhashed).

End result: we might look up an unhashed dentry that is about to be
freed, with the sequence number never indicating anything bad about it.
So checking that the dentry is still hashed (*after* reading the sequence
number) is indeed the proper fix, and was never unnecessary.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Per pull request, for 3.5.

Pull InfiniBand/RDMA changes from Roland Dreier:
 - Add ocrdma hardware driver for Emulex IB-over-Ethernet adapters
 - Add generic and mlx4 support for "raw" QPs: allow suitably privileged
   applications to send and receive arbitrary packets directly to/from
   the hardware
 - Add "doorbell drop" handling to the cxgb4 driver
 - A fairly large batch of qib hardware driver changes
 - A few fixes for lockdep-detected issues
 - A few other miscellaneous fixes and cleanups

Fix up trivial conflict in drivers/net/ethernet/emulex/benet/be.h.

* tag 'rdma-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (53 commits)
  RDMA/cxgb4: Include vmalloc.h for vmalloc and vfree
  IB/mlx4: Fix mlx4_ib_add() error flow
  IB/core: Fix IB_SA_COMP_MASK macro
  IB/iser: Fix error flow in iser ep connection establishment
  IB/mlx4: Increase the number of vectors (EQs) available for ULPs
  RDMA/cxgb4: Add query_qp support
  RDMA/cxgb4: Remove kfifo usage
  RDMA/cxgb4: Use vmalloc() for debugfs QP dump
  RDMA/cxgb4: DB Drop Recovery for RDMA and LLD queues
  RDMA/cxgb4: Disable interrupts in c4iw_ev_dispatch()
  RDMA/cxgb4: Add DB Overflow Avoidance
  RDMA/cxgb4: Add debugfs RDMA memory stats
  cxgb4: DB Drop Recovery for RDMA and LLD queues
  cxgb4: Common platform specific changes for DB Drop Recovery
  cxgb4: Detect DB FULL events and notify RDMA ULD
  RDMA/cxgb4: Drop peer_abort when no endpoint found
  RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
  mlx4_core: Change bitmap allocator to work in round-robin fashion
  RDMA/nes: Don't call event handler if pointer is NULL
  RDMA/nes: Fix for the ORD value of the connecting peer
  ...

Pull SCSI misc update from James Bottomley:
 "The patch contains the usual assortment of driver updates (be2iscsi,
  bfa, bnx2i, fcoe, hpsa, isci, lpfc, megaraid, mpt2sas, pm8001, sg)
  plus an assortment of other changes and fixes.  Also new is the fact
  that the isci update is delivered as a git merge (with signed tag)."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (158 commits)
  isci: End the RNC resumption wait when the RNC is destroyed.
  isci: Fixed RNC bug that lost the suspension or resumption during destroy
  isci: Fix RNC AWAIT_SUSPENSION->INVALIDATING transition.
  isci: Manage the IREQ_NO_AUTO_FREE_TAG under scic_lock.
  isci: Remove obviated host callback list.
  isci: Check IDEV_GONE before performing abort path operations.
  isci: Restore the ATAPI device RNC management code.
  isci: Don't wait for an RNC suspend if it's being destroyed.
  isci: Change the phy control and link reset interface for HW reasons.
  isci: Added timeouts to RNC suspensions in the abort path.
  isci: Add protocol indicator for TMF requests.
  isci: Directly control IREQ_ABORT_PATH_ACTIVE when completing TMFs.
  isci: Wait for RNC resumption before leaving the abort path.
  isci: Fix RNC suspend call for SCI_RESUMING state.
  isci: Manage tag releases differently when aborting tasks.
  isci: Callbacks to libsas occur under scic_lock and are synchronized.
  isci: When in the abort path, defeat other resume calls until done.
  isci: Implement waiting for suspend in the abort path.
  isci: Make sure all TCs are terminated and cleaned in LUN reset.
  isci: Manage the LLHANG timer enable/disable per-device.
  ...

Pull usb-gadget scsi-target merge from Nicholas Bellinger:
 "As promised, here is the pull request for Sebastian's usb-gadget
  target UASP / BOT driver for v3.5-rc1.  This code has been in
  linux-next for a number of weeks, and is now ready for an initial
  merge.

  This fabric uses the target framework to provide a usb gadget device.
  This gadget supports the USB Attached SCSI Protocol (UASP) and Bulk
  Only Transfers (BOT or BBB).  BOT is the primary interface, UAS is the
  alternative interface.

  Note this series is dependent upon a single target core patch for
  adding se_cmd->unknown_data_length in target-pending/for-next, that
  got merged in the parent.

  Kudos to Sebastian for making this driver happen so easily, and for
  his patches to improve usb-core and target core along the way to his
  goal.  Also thanks to Felipe + Greg-KH for their help in getting this
  driver ready for mainline."

* 'usb-target-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  usb-gadget: Initial merge of target module for UASP + BOT

Pull scsi-target changes from Nicholas Bellinger:
 "There has been lots of work in existing code in a number of areas this
  past cycle.  The major highlights have been:

   * Removal of transport_do_task_sg_chain() from core + fabrics
     (Roland)
   * target-core: Removal of se_task abstraction from target-core and
     enforce hw_max_sectors for pSCSI backends (hch)
   * Re-factoring of iscsi-target tx immediate/response queues (agrover)
   * Conversion of iscsi-target back to using target core memory
     allocation logic (agrover)

  We've had one last minute iscsi-target patch go into for-next to
  address a nasty regression bug related to the target core allocation
  logic conversion from agrover that is not included in friday's
  linux-next build, but has been included in this series.

  On the new fabric module code front for-3.5, here is a brief status
  update for the three currently in flight this round:

   * usb-gadget target driver:

  Sebastian Siewior's driver for supporting usb-gadget target mode
  operation.  This will be going out as a separate PULL request from
  target-pending/usb-target-merge with subsystem maintainer ACKs.  There
  is one minor target-core patch in this series required to function.

   * sbp ieee-1394/firewire target driver:

  Chris Boot's driver for supportting the Serial Block Protocol (SBP)
  across IEEE-1394 Firewire hardware.  This will be going out as a
  separate PULL request from target-pending/sbp-target-merge with two
  additional drivers/firewire/ patches w/ subsystem maintainer ACKs.

   * qla2xxx LLD target mode infrastructure changes + tcm_qla2xxx:

  The Qlogic >= 24xx series HW target mode LLD infrastructure patch-set
  and tcm_qla2xxx fabric driver.  Support for FC target mode using
  qla2xxx LLD code has been officially submitted by Qlogic to James
  below, and is currently outstanding but not yet merged into
  scsi.git/for-next..

    [PATCH 00/22] qla2xxx: Updates for scsi "misc" branch
    http://www.spinics.net/lists/linux-scsi/msg59350.html

  Note there are *zero* direct dependencies upon this for-next series
  for the qla2xxx LLD target + tcm_qla2xxx patches submitted above, and
  over the last days the target mode team has been tracking down an
  tcm_qla2xxx specific active I/O shutdown bug that appears to now be
  almost squashed for 3.5-rc-fixes."

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (47 commits)
  iscsi-target: Fix iov_count calculation bug in iscsit_allocate_iovecs
  iscsi-target: remove dead code in iscsi_check_valuelist_for_support
  target: Handle ATA_16 passthrough for pSCSI backend devices
  target: Add MI_REPORT_TARGET_PGS ext. header + implict_trans_secs attribute
  target: Fix MAINTENANCE_IN service action CDB checks to use lower 5 bits
  target: add support for the WRITE_VERIFY command
  target: make target_put_session void
  target: cleanup transport_execute_tasks()
  target: Remove max_sectors device attribute for modern se_task less code
  target: lock => unlock typo in transport_lun_wait_for_tasks
  target: Enforce hw_max_sectors for SCF_SCSI_DATA_SG_IO_CDB
  target: remove the t_se_count field in struct se_cmd
  target: remove the t_task_cdbs_ex_left field in struct se_cmd
  target: remove the t_task_cdbs_left field in struct se_cmd
  target: remove struct se_task
  target: move the state and execute lists to the command
  target: simplify command to task linkage
  target: always allocate a single task
  target: replace ->execute_task with ->execute_cmd
  target: remove the task_sectors field in struct se_task
  ...