Received from Mark Salyzyn from Adaptec.

Fixes a bug in check_revision.  It should return the driver version not
the firmware version.
Update driver version number.
Update driver version string.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn from Adaptec:

If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.

This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.

Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

I ran into this one sending bus resets across the hardware.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch upports all relevant code fixes and bumps the driver version
to 7.0 to signify starting a new tree.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

since this card can support the setting, add it to the parameter list.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant.  However,
just in case anyone should want to do this, it's appropriate to include
the parameter.

I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.

I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus).  If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.

I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch updates the aic79xx driver to take advantage of the
scsi_transport_spi infrastructure. Patch is quite a mess as some
procedures have been reshuffled to be closer to the aic7xxx driver.

Rejections fixed and
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

From: Jeff Garzik <jgarzik@pobox.com>

This patch removes the busyq in aic79xx and uses the command-queue from 
the midlayer instead. Additionally some dead code is removed.
Signed-off-by: NHannes Reinecke <hare@suse.de>

Fixed rejections
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

we have the most recent microcode, make sure to always load it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

print message tidy ups and some excess brace removal.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NThiemo Seufer <ths@linux-mips.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fixes up some warnings in the tree.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add support to not allow additions to a host when it is being removed.
Signed-off-by: NMike Anderson <andmike@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove the old scsi_host_cancel function as it has not been working for
sometime do to the device list possibly being empty when it is called and
possible race issues. Add setting of SHOST_CANCEL at the state of beginning
of scsi_remove_host.
Signed-off-by: NMike Anderson <andmike@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Migrate the current SCSI host state model to a model like SCSI
device is using.
Signed-off-by: NMike Anderson <andmike@us.ibm.com>

Rejections fixed up and
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It seems very unlikely that this driver will go into any stable kernel
before devfs will be removed.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 aic doesnt work anymore after this change which appeared int 2.6.13-rc1:
 [SCSI] aic7xxx/aic79xx: remove useless byte order macro cruft

 2 files did not include byteorder.h, aic died with panic
 "Unknown opcode encountered in seq program"
 This patch fixes it for me.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot.  This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register.  If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly.  The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE.  On resume, this is then written after APSIZE
has been set.  This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.

Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix inline assembly that gets miscompiled by gcc 4.
Signed-off-by: NGerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational.  (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch that introduced waiting for interrupts after resetting the reader
can cause the boot to fail because the system is waiting for an interrupt that
will never arrive.  Add code to check if an interrupt is supposed to arrive
before waiting endlessly.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update default configuration of s390.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The #if/#ifdef cleanup exposed a bug in UML's ELF header processing.  With
this bug fixed, UML recognizes the vsyscall info coming from the host.  On
FC4, there is a vsyscall page low in the address space, which UML doesn't
provide.  This causes an infinite page fault loop and a hang on boot.

This patch works around that by making this look like a no-vsyscall system.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Do not use memcpy in fb_pad_aligned_buffer.  It is suboptimal because only
a few bytes are moved at a time.  Replace with a for-loop.
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device.  The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided.  Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up.  The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices.  The patch corrects this
problem by allowing PCI IRQs below 16.

Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

>> vesafb: mode is 800x600x16, linelength=1600, pages=16
>> vesafb: scrolling: redraw
>> vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
>> mtrr: type mismatch for fc000000,1000000 old: write-back new: write-
>> combining

Range is already set to write-back, vesafb attempts to add a write-combining
mtrr (default for vesafb).

>> mtrr: size and base must be multiples of 4 kiB

This is a bug, vesafb attempts to add a size < PAGE_SIZE triggering
the messages below.

To eliminate the warning messages, you can add the option mtrr:2 to add a
write-back mtrr for vesafb.  Or just use nomtrr option.

1. Fix algorithm for finding the best power of 2 size with mtrr_add().

2. Add option to choose the mtrr type by extending the mtrr boot option:

   mtrr:n where n

        0 = no mtrr (equivalent to using the nomtrr option)
        1 = uncachable
        2 = write back
        3 = write combining (default)
        4 = write through
Signed-off-by: NAntonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support for UARTs in MMIO space and clean up a little whitespace.

HP legacy-free ia64 machines need this.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value.  smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi.  There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt.  Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.

Why cli does not protect us from that is beyond me.

The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.

This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.

Minor changes by AK
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

While reserving KVA for lmem_maps of node, we have to make sure that
node_remap_start_pfn[] is aligned to a proper pmd boundary.
(node_remap_start_pfn[] gets its value from node_end_pfn[])
Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: NShai Fultheim <shai@scalex86.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It seems that I see a bug in hidinput_hid_event.  The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.

Cc: <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>