This is no longer necessary since we only update the staged config on
successfull modeset. The new configuration is stored in an atomic state
struct which is freed in case of failure.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes disabling planes more explicit.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
[anderco: fixed warning due to using drm_crtc instead of intel_crtc]
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They're the same code, so why not?
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was an optimization from way back before we had primary plane
support to be able to disable the primary plane. But with primary
plane support userspace can tell the kernel this directly, so there's
no big need for this any more. And it's getting in the way of the
atomic conversion.

If need be we can resurrect this later on properly again.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Explain why removing this is ok.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is used by the next commit to disable all planes on a crtc
without caring what type it is.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of the flags that were used are still useful when transitioning
to atomic, so keep those around for now. This removes some of the
complications of crtc->primary_enabled, making it easier to remove.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Updates the EDID compliance test function to perform the analyze and react to
the EDID data read as a result of a hot plug event. The results of this
analysis are handed off to userspace so that the userspace app can set the
display mode appropriately for the test result/response.

The compliance_test_active flag now appears at the end of the individual
test handling functions. This is so that the kernel-side operations can
be completed without the risk of interruption from the userspace app
that is polling on that flag.

V2:
- Addressed mailing list feedback
- Removed excess debug messages
- Removed extraneous comments
- Fixed formatting issues (line length > 80)
- Updated the debug message in compute_edid_checksum to output hex values
  instead of decimal
V3:
- Addressed more list feedback
- Added the test_active flag to the autotest function
- Removed test_active flag from handler
- Added failsafe check on the compliance test active flag
  at the end of the test handler
- Fixed checkpatch.pl issues
V4:
- Removed the checksum computation function and its use as it has been
  rendered superfluous by changes to the core DRM EDID functions
- Updated to use the raw header corruption detection mechanism
- Moved the declaration of the test_data variable here
V5:
- Update test active flag variable name to match the change in the
  first patch of the series.
- Relocated the test active flag declaration and initialization
  to this patch
V6:
- Updated to use the new flag for raw EDID header corruption
- Removed the extra EDID read from the autotest function
- Added the edid_checksum variable to struct intel_dp so that the
  autotest function can write it to the sink device
- Moved the update to the hpd_pulse function to another patch
- Removed extraneous constants
V7:
- Fixed erroneous placement of the checksum assignment. In some cases
  such as when the EDID read fails and is NULL, this causes a NULL ptr
  dereference in the kernel. Bad news. Fixed now.
V8:
- Updated to support the kfree() on the EDID data added previously
V9:
- Updated for the long_hpd flag propagation
V10:
- Updated to use actual checksum from the EDID read that occurs during
  normal hot plug path execution
- Removed variables from intel_dp struct that are no longer needed
- Updated the patch subject to more closely match the nature and contents
  of the patch
- Fixed formatting problem (long line)
V11:
- Removed extra debug messages
- Updated comments to be more informative
- Removed extra variable
V12:
- Removed the 4 bit offset of the resolution setting in compliance data
- Changed to DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER
Signed-off-by: NTodd Previte <tprevite@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a first of series patches that optimize DP link
training. The first patch is for eDP only where we reuse
the previously trained link training values from cache
i.e. voltage swing and pre-emphasis levels.

In case we are not able to train the link by reusing
the known values, the link training parameters are set
to zero and training is restarted.

V2:
- flag that indicates if DP link is trained and valid
  renamed from 'link_trained' to 'train_set_valid'
- removed routine 'intel_dp_reuse_link_train'

V3:
- rebased against the latest drm-intel-nightly

V4:
- removed HPD long pulse handling for eDP case to clear the
  flag that indicates to reuse the current link training
  parameters. (based on Sivakumar's comment)
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[danvet: s/DP/eDP/ in subject to make scope clear.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by scripts/coccinelle/api/err_cast.cocci
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.

v2: Removed camelcase in functions and variables.

v3: Do some minimal check to assert if CSR program is not loaded.

v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
   new ones.
4] Changed variable names as updated in earlier patches.

v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
   particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.

v6: Remove use of dc5_enabled variable as it's no longer needed.

v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.

v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.

Also call POSTING_READ for every write to a register to ensure that
its written immediately.

v1: Remove POSTING_READ calls as they've already been added in previous patches.

v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.

Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
   functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
   gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
   to warnings. However, removing them for now as they'll be included in a future patch
   asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
   to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
   runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
   accessed during deferred DC5-enabling, are not initialized earlier.

v3: Rebase to latest.

Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5  for simplicity, instead of
   deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
   enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
   functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
   DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.

v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.

v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
   accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.

v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)

v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.

v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.

This implementation is added based on first version of DMC CSR program
that we received from h/w team.

Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.

For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.

As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.

v1: Initial relese as RFC patch

v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.

v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.

v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.

v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.

Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.

v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.

v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.

v8: Rebase to latest.

v9: Rebase on top of -nightly (Damien)

v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)

v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)

v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)

v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)

v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)

v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)

v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)

Issue: VIZ-2569
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake primary plane scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)

v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
 is using drm_plane->state rect instead of intel_plane->state rect.
 This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
 Added helper functions for refactoring are comprehended enough to be
 used for skylake_update_plane (for sprite) too. One stop towards
 having single function for all planes.

v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have grown a number of different implementations of
DIV_ROUND_CLOSEST_ULL throughout the kernel.  Move the i915 one to
kernel.h so that it can be reused.
Signed-off-by: NJavi Merino <javi.merino@arm.com>
Reviewed-by: NJeff Epler <jepler@unpythonic.net>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the skeleton framework for supporting automation for Displayport compliance
testing. This patch adds the necessary framework for the source device to
appropriately respond to test automation requests from a sink device.

V2:
- Addressed previous mailing list feedback
- Fixed compilation issue (struct members declared in a later patch)
- Updated debug messages to be more accurate
- Added status checks for the DPCD read/write calls
- Removed excess comments and debug messages
- Fixed debug message compilation warnings
- Fixed compilation issue with missing variables
- Updated link training autotest to ACK

V3:
- Fixed the checks on the DPCD return code to be <= 0
  rather than != 0
- Removed extraneous assignment of a NAK return code in the
  DPCD read failure case
- Changed the return in the DPCD read failure case to a goto
  to the exit point where the status code is written to the sink
- Removed FAUX test case since it's deprecated now
- Removed the compliance flag assignment in handle_test_request

V4:
- Moved declaration of type_type here
- Removed declaration of test_data (moved to a later patch)
- Added reset to 0 for compliance test variables

V5:
- Moved test_active variable declaration and initialization out of
  this patch and into the patch where it's used
- Changed variable name compliance_testing_active to
  compliance_test_active to unify the naming convention
- Added initialization for compliance_test_type variable
Signed-off-by: NTodd Previte <tprevite@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VSwing programming sequence as specified in the updated BXT BSpec

v2: Satheesh's review comments addressed.
- clear value before setting into registers
- move print statement to bxt function
Other changes
- since signal level will not be set into DDI_BUF_CTL, the value need
  not be returned to intel_dp_set_signal_levels(). Making the bxt
  specific function to return void and setting signal_levels = 0 for
  bxt inside intel_dp_set_signal_levels()
- instead of signal levels, printing vswing level and pre-emphasis
  level
- in case none of the pre-emphasis levels or vswing levels are set,
  setting default of 400mV + 0dB

v3: Satheesh's review comments
- Check for mask before printing signal_levels.
- Removing redundant register writes
- Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT
- Making register write part generic as it will be required for HDMI as
  well.

Re-structure the code to include an array for vswing related values, set
signal levels

v4: Satheesh's review comments
- Rebase over latest renaming patches
- use hsw_signal_levels for HAS_DDI
Other changes
- Modified vswing_sequence() func definition
- Rebased on top of register macro definitions

v5: Satheesh's review comments
- Check ddi translation table size

v6: Imre's review comments
- removed comments in vswing sequence
- added vswing, pre-emphasis prints in intel_dp_set_signal_levels
- added comment explaining use of DP vswing values for eDP
- initialize n_entries and ddi_transaltion table based on encoder type
- create bxt_ddi_buf_trans structure and use decimal values
- adding a flag in bxt buffer translation table to indicate def entry

v7: (imre)
- squash in Vandana's "VSwing register definition",
  "HDMI VSwing programming", "Re-enable vswing programming",
  "Fix vswing sequence" patches
- use BXT_PORT_* regs directly instead of via a temp var
- simplify BXT_PORT_* macro definitions
- add code comment why we read lane while write group registers
- fix readout of DP_TRAIN_PRE_EMPHASIS in debug message

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Assign PLL for pipe (dependent on port attached to the pipe)

v2:
- fix incorrect encoder vs. new_encoder check for crtc (imre)

v3:
- warn and return error if no encoder is attached (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't move intel_ddi_get_crtc_new_encoder around.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Modified as per review comments from Imre
- Mention enabling instead of allowing in the debug trace and
  remove unnecessary comments.

v3:
- Rebase to latest.
- Move DC9-related functions from intel_display.c to intel_runtime_pm.c.

v4: (imre)
- remove DC5 disabling, it's a nop at this point
- squashed in Suketu's "Assert the requirements to enter or exit DC9"
  patch
- remove check for RUNTIME_PM from assert_can_enable_dc9, it's not a
  dependency

Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v3)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add PHY specific display initialization sequence as per BSpec.

Note that the PHY initialization/uninitialization are done
at their current place only for simplicity, in a future patch - when more
of the runtime PM features will be enabled - these will be moved to
power well#1 and modeset encoder enabling/disabling hooks respectively.

The call to uninitialize the PHY during system/runtime suspend will be
added later in this patchset.

v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set

v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- fix DDI PHY timeout value
- squash in Vandana's "PORT_CL2CM_DW6_A BUN fix",
  "DDI PHY programming register defn", "Do ddi_phy_init always",
- move PHY register macros next to the corresponding CHV/VLV macros
- move DE PLL register macros here from another patch since they are
  used here first
- add BXT_ prefix to CDCLK flags
- s/COMMON_RESET/COMMON_RESET_DIS/ and clarify related code comments
- fix incorrect read value for the RMW of BXT_PHY_CTL_FAMILY_DDI
- fix using GT_DISPLAY_EDP_POWER_ON vs. GT_DISPLAY_DDI_POWER_ON
  when powering on DDI ports
- fix incorrect port when setting BXT_PORT_TX_DW14_LN for DDI ports
- add missing masking when programming CDCLK_FREQ_DECIMAL
- add missing powering on for DDI-C port, rename OCL2_LDOFUSE_PWR_EN
  to OCL2_LDOFUSE_PWR_DIS to reduce confusion
- add note about mismatch with bspec in the PORT_REF_DW6 fields
- factor out PHY init code to a new function, so we can call it for
  PHY1 and PHY0, instead of open-coding the same

v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
  accordingly
- use the existing dpio_phy enum instead of adding a new one for the
  same purpose
- flip the meaning of PHYs so that PHY_A is PHY1 and PHY_BC is PHY0 to
  better match CHV
- s/BXT_PHY/_BXT_PHY/
- use _PIPE for _BXT_PHY instead of open-coding it
- drop _0_2_0_GTTMMADR suffix from BXT_P_CR_GT_DISP_PWRON
- define GT_DISPLAY_POWER_ON in a more standard way
- make a note that the CHV ConfigDB also disagrees about GRC_CODE field
  definitions
- fix lane optimization refactoring fumble from v3
- add per PHY uninit functions to match the init counterparts

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add CDCLK specific display clock initialization sequence as per BSpec.

Note that the CDCLK initialization/uninitialization are done at their
current place only for simplicity, in a future patch - when more of the
runtime PM features will be enabled - these will be moved to power
well#1 and modeset encoder enabling/disabling hooks respectively. This
also means that atm dynamic power gating power well #1 is effectively
disabled.

The call to uninitialize CDCLK during system/runtime suspend will be
added later in this patchset.

v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set

v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- move DE PLL register macros here from another patch since they are
  used here first
- add BXT_ prefix to CDCLK flags
- add missing masking when programming CDCLK_FREQ_DECIMAL

v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
  accordingly
- s/DISPLAY_PCU_CONTROL/HSW_PCODE_DE_WRITE_FREQ_REQ/
- simplify BXT_DE_PLL_RATIO macros
- fix BXT_DE_PLL_RATIO_MASK
- s/bxt_select_cdclk_freq/broxton_set_cdclk_freq/
- move cdclk init/uninit/set code from intel_ddi.c to intel_display.c
- remove redundant code comments for broxton_set_cdclk_freq()
- sanitize fixed point<->integer frequency value conversion
- use DRM_ERROR instead of WARN
- do RMW when programming BXT_DE_PLL_CTL for safety
- add note about PLL lock timeout being exactly 200us
- make PCU error messages more descriptive
- instead of using 0 freq to mean PLL off/bypass freq use 19200
  for clarity, as the latter one is the actual rate
- simplify pcode programming, removing duplicated
  sandybridge_pcode_write() call
- sanitize code flow, remove unnecessary scratch vars in
  broxton_set_cdclk() (imre)
- Remove bound check for maxmimum freq to match current code.
  This check will be added later at a more proper platform
  independent place once atomic support lands.
- add note to remove freq guard band which isn't needed on BXT
- add note to reduce freq to minimum if no pipe is enabled
- combine broxton_modeset_global_pipes() with
  valleyview_modeset_global_pipes()

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to spec: "In PSR HW or SW mode, SW set this bit before writing
registers for a flip. It will be self-clear when it gets to the PSR
active state."

Some versions of spec mention that this is needed when in
"Persistent mode" but define it as same as "SW mode". Since this
fix the page flip case let's assume this is exactly what we need.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.

Broken by

commit 944b0c76
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Fri Mar 20 16:18:07 2015 +0200

    drm/i915: Copy the staged connector config to the legacy atomic state

v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: NNicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Enabling skylake panel fitting feature using shared scalers

v2:
-added force detach parameter for pfit disable purpose (me)
-read crtc scaler state from hw state (Daniel)
-replaced both skylake_pfit_enable and disable with skylake_pfit_update (me)
-added scaler id check to intel_pipe_config_compare (Daniel)

v3:
-updated function header to kerneldoc format (Matt)
-dropped need_scaling checks (Matt)

v4:
-move clearing of scaler id from commit path to check path (Matt)
-updated colorkey checks based on recent updates (me)
-squashed scaler check while enabling colorkey to here (me)
-use values in plane_state->src as regular integers (me)
-changes made not to modify state in commit path (Matt)

v5:
-squashed helper function to update scaler users to here (Matt)
-squashed helper function to detach scaler to here (Matt, me)
-changes to align with updated scaler structures (Matt, me)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added intel_atomic_setup_scalers to setup scalers based on
staged scaling requests from a crtc and its planes. If staged
requests are supportable, this function assigns scalers to
requested planes and crtc. Note that the scaler assignement
itself is staged into crtc_state and respective plane_states
for later commit after all checks have been done.

overall high level flow:
 - scaler requests are staged into crtc_state by planes/crtc
 - check whether staged scaling requests can be supported
 - add planes using scalers that aren't in current transaction
 - assign scalers to requested users
 - as part of plane commit, scalers will be committed
   (i.e., either attached or detached) to respective planes in hw
 - as part of crtc_commit, scaler will be either attached or detached
   to crtc in hw

crtc_compute_config calls intel_atomic_setup_scalers() to start
scaler assignments as per scaler state in crtc config. This call
should be moved to atomic crtc once it is available.

v2:
-removed a log message (me)
-changed input parameter to crtc_state (me)

v3:
-remove assigning plane_state returned by drm_atomic_get_plane_state (Matt)
-fail if there is an error from drm_atomic_get_plane_state (Matt)

v4:
-changes to align with updated scaler structure (Matt, me)

v5:
-added addtional checks before enabling HQ mode (me)
-added comments to enable HQ mode (Matt)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

skylake scaler structure definitions. scalers live in crtc_state as
they are pipe resources. They can be used either as plane scaler or
panel fitter.

scaler assigned to either plane (for plane scaling) or crtc (for panel
fitting) is saved in scaler_id in plane_state or crtc_state respectively.

scaler_id is used instead of scaler pointer in plane or crtc state
to avoid updating scaler pointer everytime a new crtc_state is created.

v2:
-made single copy of min/max values for scalers (Matt)

v3:
-updated commentary for scaler_id (me)

v4:
-converted src/dst ranges to #defines, dropped ratios (Matt)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Connector states were being allocated in intel_setup_outputs() in loop
over all connectors. That meant hot-added connectors would have a NULL
state. Since the change to use a struct drm_atomic_state for the legacy
modeset, connector states are necessary for the i915 driver to function
properly, so that would lead to oopses.

v2: Fix test for intel_connector_init() success in lvds and sdvo (PRTS)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reported-and-tested-by: NNicolas Kalkhof <nkalkhof@web.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Moving creation of property in a function, checking for 90/270
rotation simultaneously (Chris)
Letting primary plane to be positioned
v3: Adding if/else for 90/270 and rest params programming, adding check for
pixel_format, some cleanup (review comments)
v4: Adding right pixel_formats, using src_* params instead of crtc_* for offset
and size programming (Ville)
v5: Rebased on -nightly and Tvrtko's series for gtt remapping.
v6: Rebased on -nightly (Tvrtko's series merged)
v7: Moving pixel_format check to intel_atomic_plane_check (Matt)
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With boosting for missed pageflips, we have a much stronger indication
of when we need to (temporarily) boost GPU frequency to ensure smooth
delivery of frames. So now only allow each client to perform one RPS boost
in each period of GPU activity due to stalling on results.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we hit a vblank and see that have a pageflip queue but not yet
processed, ensure that the GPU is running at maximum in order to clear
the backlog. Pageflips are only queued for the following vblank, if we
miss it, there will be a visible stutter. Boosting the GPU frequency
doesn't prevent us from missing the target vblank, but it should help
the subsequent frames hitting theirs.

v2: Reorder vblank vs flip-complete so that we only check for a missed
flip after processing the completion events, and avoid spurious boosts.

v3: Rename missed_vblank
v4: Rebase
v5: Cancel the outstanding work in runtime suspend
v6: Rebase
v7: Rebase required fixing
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Deepak S<deepak.s@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not needed anymore, now that all the users were converted to using
an atomic state.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Unify the HSW/BDW/SKL cdclk extraction code to conform to the same
.get_display_clock_speed() mold that all the other platforms
use.

v2: Update due to SKL code getting added

v3: Rebase on top of -nightly (introduction of intel_audio.c) (Mika Kahola)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Add v3 note as suggested by Damien.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's completely unused and Tommi noticed that the #define is borked
since forever. I've done a git search in userspace and only found
broken definitions and no users anywhere.

Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

For now this is not necessary since intel_set_mode() doesn't acquire any
new locks. However, once that function is converted to atomic, that will
change, since we'll pass an atomic state to it, and that needs to have
the right acquire context set.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The pattern of getting the crtc state with drm_atomic_get_crtc_state()
and then converting it to intel_crtc_state will repeat quite often in
the following patches, so add a helper function to save some typing.

v2: Fix upcasting so that crtc_state base field could be moved. (Daniel)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Pass in rotation info to sprite plane updates as well.

v3: Use helper to determine 90/270 rotation. (Michel Thierry)

v4: Rebased for fb modifiers and atomic changes.

For: VIZ-4546
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v3)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Need to do this in order to support 90/270 rotated display.

v2: Pass in drm_plane instead of plane index to intel_obj_display_address.

v3:
    * Renamed intel_obj_display_address to intel_plane_obj_offset.
      (Chris Wilson)
    * Simplified rotation check to bitwise AND. (Chris Wilson)

v4:
    * Extracted 90/270 rotation check into a helper function. (Michel Thierry)

v5:
    * Rebased for ggtt view changes.

For: VIZ-4545
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

90/270 rotated scanout needs a rotated GTT view of the framebuffer.

This is put in a separate VMA with a dedicated ggtt view and wired such that
it is created when a framebuffer is pinned to a 90/270 rotated plane.

Rotation is only possible with Yb/Yf buffers and error is propagated to
user space in case of a mismatch.

Special rotated page view is constructed at the VMA creation time by
borrowing the DMA addresses from obj->pages.

v2:
    * Do not bother with pages for rotated sg list, just populate the DMA
      addresses. (Daniel Vetter)
    * Checkpatch cleanup.

v3:
    * Rebased on top of new plane handling (create rotated mapping when
      setting the rotation property).
    * Unpin rotated VMA on unpinning from display plane.
    * Simplify rotation check using bitwise AND. (Chris Wilson)

v4:
    * Fix unpinning of optional rotated mapping so it is really considered
      to be optional.

v5:
   * Rebased for fb modifier changes.
   * Rebased for atomic commit.
   * Only pin needed view for display. (Ville Syrjälä, Daniel Vetter)

v6:
   * Rebased after preparatory work has been extracted out. (Daniel Vetter)

v7:
   * Slightly simplified tiling geometry calculation.
   * Moved rotated GGTT view implementation into i915_gem_gtt.c (Daniel Vetter)

v8:
   * Do not use i915_gem_obj_size to get object size since that actually
     returns the size of an VMA which may not exist.
   * Rebased for ggtt view changes.

v9:
   * Rebased after code review changes on the preceding patches.
   * Tidy function definitions. (Joonas Lahtinen)

For: VIZ-4726
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v4)
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Plane state carries the rotation information which is needed for determining
the appropriate GGTT view type.

This just adds the parameter with the actual usage coming in future patches.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It will be used in a later patch and also convert all height parameters
from int to unsigned int.

v2: Rebased for fb modifiers.
v3: Fixed v2 rebase.
v4:
   * Height should be unsigned int.
   * Make it take pixel_format for consistency and simplicity.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com> (v1)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v4)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>