When reading/writing a subpage (When HW ECC is not available/enabled)
for number of bytes not aligned to 4, the mis-aligned bytes are handled
first (by cpu copy method) before enabling the Prefetch engine to/from
'p'(start of buffer 'buf'). Then it reads/writes rest of the bytes with
the help of Prefetch engine, if available, or again using cpu copy method.
Currently, reading/writing of rest of bytes, is not done correctly since
its trying to read/write again to/from begining of buffer 'buf',
overwriting the mis-aligned bytes.

Read & write using prefetch engine got broken in commit '2c01946c'.
We never hit a scenario of not getting 'gpmc_prefetch_enable' call
success. So, problem did not get caught up.
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NVimal Singh <vimal.newwork@gmail.com>
Reported-by: NBryan DE FARIA <bdefaria@adeneo-embedded.com>
Cc: stable@kernel.org [2.6.35+]
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The previous section mismatch fix for this driver wasn't entirely correct.
The sst25l_flash_info array is now used in the devinit probe func, but is
marked as initdata, so building results in the warning:

WARNING: drivers/mtd/devices/sst25l.o(.devinit.text): Section mismatch
	in reference from the function sst25l_probe()
	to the variable .init.data:sst25l_flash_info

Further, the remove func should be devexit rather than exit to match the
probe func.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

S25FL512S = 64MiB single die, same family as S25FL256S
S70FL01GS = 2x S25FL512S dies in one package (separate chip selects)

These devices are not sampling yet, but they are expected to be very
similar to S25FL256S, which has been tested.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

These are 32MiB parts which use a slightly different 4-byte enable
sequence from Macronix.

Default to the Spansion 4-byte scheme in set_4byte(), as it is more
likely to be copied by other vendors.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the manufacturer ID names from cfi.h instead of hard-coding
hex constants.  Introduce a JEDEC_MFR macro for clarity.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Not all configurations of the Denali controller support 4 banks.  The
controller can support between 1 and 16 banks.  Detect this from the
design features register.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The controller has interrupt enable/status register pairs for each bank
(along with ECC and status registers) that differ only in address offset.
Rather than providing definitions for each register, make the address a
macro so that it scales for devices with different numbers of banks.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Rather than using the PCI specific DMA API, convert to the generic
DMA API so that we can use the Denali NAND controller on other bus
types.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Coverity has reported that inside the function "onenand_block_by_block_erase()"
in onenand_base.c, we should add a check to prevent the incrementing of
possible NULL value for "region"
Signed-off-by: NMaxin B. John <john.maxin@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In commit c7b28e25 the initialization of
the backblockbits was accidentally removed. This patch returns it back,
because otherwise some NAND drivers are broken.

This problem was reported by "Saxena, Parth <parth.saxena@ti.com>" here:
http://lists.infradead.org/pipermail/linux-mtd/2011-April/035221.htmlReported-by: NSaxena, Parth <parth.saxena@ti.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Tested-by: NSaxena, Parth <parth.saxena@ti.com>
Acked-by: NSaxena, Parth <parth.saxena@ti.com>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Cc: stable@kernel.org [2.6.36+]
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch extends NDFC driver to support all 4 chip selects
available in NDFC NAND controller. Tested on custom 460EX board
with 2 chip select NAND device.

Artem: white-space cleanups
Signed-off-by: NFelix Radensky <felix@embedded-sol.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Replace direct call to kmalloc for a potentially large, contiguous
buffer allocation with one to mtd_kmalloc_up_to which helps ensure the
operation can succeed under low-memory, highly- fragmented situations
albeit somewhat more slowly.
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Replace direct call to kmalloc for a potentially large, contiguous
buffer allocation with one to mtd_kmalloc_up_to which helps ensure the
operation can succeed under low-memory, highly- fragmented situations
albeit somewhat more slowly.
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Tested-by: NBen Gardiner <bengardiner@nanometrics.ca>
Tested-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Introduce a common function to handle large, contiguous kmalloc buffer
allocations by exponentially backing off on the size of the requested
kernel transfer buffer until it succeeds or until the requested
transfer buffer size falls below the page size.

This helps ensure the operation can succeed under low-memory, highly-
fragmented situations albeit somewhat more slowly.

Artem: so this patch solves the problem that the kernel tries to kmalloc too
large buffers, which (a) may fail and does fail - people complain about this,
and (b) slows down the system in case of high memory fragmentation, because
the kernel starts dropping caches, writing back, swapping, etc. But we do not
really have to allocate a lot of memory to do the I/O, we may do this even with
as little as one min. I/O unit (NAND page) of RAM. So the idea of this patch is
that if the user asks to read or write a lot, we try to kmalloc a lot, with GFP
flags which make the kernel _not_ drop caches, etc. If we can allocate it - good,
if not - we try to allocate twice as less, and so on, until we reach the min.
I/O unit size, which is our last resort allocation and use the normal
GFP_KERNEL flag.

Artem: re-write the allocation function so that it makes sure the allocated
buffer is aligned to the min. I/O size of the flash.
Signed-off-by: NGrant Erickson <marathon96@gmail.com>
Tested-by: NBen Gardiner <bengardiner@nanometrics.ca>
Tested-by: NStefano Babic <sbabic@denx.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Currently mtdconcat is broken for NAND. An attemtpt to create
JFFS2 filesystem on concatenation of several NAND devices fails
with OOB write errors. This patch fixes that problem.
Signed-off-by: NFelix Radensky <felix@embedded-sol.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

nand_scan calls nand_scan_tail and here we got a ecc.layout and calculate
oobavail for this layout. After calling nand_scan, we change the layout pointer
if OMAP_ECC_HAMMING_CODE_HW_ROMCODE is set. This results in not calcluated
oobavail. Mountig as jffs2 is not possible.

To fix that nand_scan has to split up in nand_scan_ident and nand_scan_tail
setting ecc.layout between these calls. So nand_scan_tail calculates oobvail
for the used layout. This is also done in serveral other platforms.
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Reviewed-by: NVimal Singh <vimal.newwork@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The 'blktrans_open()' does not handle possible '__get_mtd_device()' failures
because it does not check the error code. Moreover, the 'dev->tr->open()'
failures are not handled correctly because in this case the function just
goes ahead and gets the mtd device, then returns an error. But Instead, it
should _not_ try to get the mtd device, then it should put back the module
and the kref.

This patch fixes the issue. Note, I only compile-tested it. This patch was
inspired by a bug report about a similar issue in 2.6.34 kernels
sent by Mike Turner <admin@islandsoftware.co.uk> to the MTD mailing list:

http://lists.infradead.org/pipermail/linux-mtd/2011-April/034980.htmlSigned-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Including linux/dmaengine.h fixes the missing definition of the enum
dma_ctrl_flags type used in atmel_nand_dma_op function.
Signed-off-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Chip deselection is already done in nand_release_device. So only
duplicate code.
Signed-off-by: NJiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Current implementation of s3c2410_nand_select_chip call
clk_disable every time when chip = -1 (de-select). This happend
multiple times even if chip was already de-selected. This causes
disabling clock even if they are already disabled and due to
nature of clock subsytem implementation this causes nand clock
to be disabled and newer enabled again.
Signed-off-by: NJiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch adds CFI 1.5 support for the new Spansion S29GL-S device family.
For details, see the data sheet on the Spansion web site:
http://www.spansion.com/Support/Datasheets/S29GL_128S_01GS_00_02_e.pdfSigned-off-by: NGernot Hoyler <Gernot.Hoyler@spansion.com>
Acked-by: NGuillaume LECERF <glecerf@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

So as the ecclayout and suppage size for 4KiB page
Flex- and none-Flex OneNAND are different
the new values for none-Flex 4KiB page OneNAND memory are added.

The introduced ecclayout and suppage size are based on specification
4Gib M-die OneNAND Flash (KFM4G16Q4M, KFN8G16Q4M). Rev. 1.3, Apr. 2010
For eccpos we expose only 64 bytes out of 72, for oobfree the spare area
fields marked as "Managed by internal ECC logic for Logical Sector Number area"
are used.
Signed-off-by: NRoman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.
Signed-off-by: NMichal Marek <mmarek@suse.cz>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

It is nicer to dynamically create our badblock patterns than to
statically define them. The nand_create_default_bbt_descr() function
does a sufficient job of handling various bad block scanning options
for either flash-based or non-flash-based BBTs, so we might as well
use the function for both cases.

This patch simplifies and shortens our code (and removes a TODO that
I left a few months ago).
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The NAND_USE_FLASH_BBT_NO_OOB and NAND_CREATE_EMPTY_BBT flags conflict
with the NAND_BBT_SCANBYTE1AND6 and NAND_BBT_DYNAMICSTRUCT flags,
respectively. This change will allow us to utilize these options
independently.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Remove unused 'jffs2_sb_info *c' variable from 'jffs2_lookup()'
and 'jffs2_readdir()'.
Signed-off-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Do the following to add support for up to 4 chips on V21 devices (i.MX25 and
i.MX35):

* implement .select_chip for V21
* adjust existing NFC_V1_V2_BUF_ADDR writes to take chip select into account
* unlock all chip selects at preset_v1_v2()
* scan up to 4 devices at .probe

This has been tested on i.MX25 with two attached NAND chip (on one die).
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  configfs: Fix race between configfs_readdir() and configfs_d_iput()
  configfs: Don't try to d_delete() negative dentries.
  ocfs2/dlm: Target node death during resource migration leads to thread spin
  ocfs2: Skip mount recovery for hard-ro mounts
  ocfs2/cluster: Heartbeat mismatch message improved
  ocfs2/cluster: Increase the live threshold for global heartbeat
  ocfs2/dlm: Use negotiated o2dlm protocol version
  ocfs2: skip existing hole when removing the last extent_rec in punching-hole codes.
  ocfs2: Initialize data_ac (might be used uninitialized)

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  drivercore: revert addition of of_match to struct device
  of: fix race when matching drivers

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Kludge IP27 build for 2.6.39.
  MIPS: AR7: Fix GPIO register size for Titan variant.
  MIPS: Fix duplicate invocation of notify_die.
  MIPS: RB532: Fix iomap resource size miscalculation.

Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time.  This was unsafe
because matching is not an atomic operation with probing a driver.  If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.

This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.

Only write the result if the device matches.

In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NMilton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once]
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't delay blk_run_queue_async
  scsi: remove performance regression due to async queue run
  blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
  block: rescan partitions on invalidated devices on -ENOMEDIA too
  cdrom: always check_disk_change() on open
  block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.

[ralf@linux-mips.org: Fixed the fix.  The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Initial patch by Yury Polyanskiy <ypolyans@princeton.edu>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2373/

This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>