提交 c89eeda8 编写于 作者: J Jamie Iles 提交者: David Woodhouse

mtd: denali: detect the number of banks

Not all configurations of the Denali controller support 4 banks.  The
controller can support between 1 and 16 banks.  Detect this from the
design features register.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
上级 9589bf5b
......@@ -178,11 +178,11 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
dev_dbg(denali->dev, "%s, Line %d, Function: %s\n",
__FILE__, __LINE__, __func__);
for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++)
for (i = 0 ; i < denali->max_banks; i++)
iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
denali->flash_reg + INTR_STATUS(i));
for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++) {
for (i = 0 ; i < denali->max_banks; i++) {
iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
while (!(ioread32(denali->flash_reg +
INTR_STATUS(i)) &
......@@ -194,7 +194,7 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
"NAND Reset operation timed out on bank %d\n", i);
}
for (i = 0; i < LLD_MAX_FLASH_BANKS; i++)
for (i = 0; i < denali->max_banks; i++)
iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
denali->flash_reg + INTR_STATUS(i));
......@@ -405,11 +405,11 @@ static void get_hynix_nand_para(struct denali_nand_info *denali,
*/
static void find_valid_banks(struct denali_nand_info *denali)
{
uint32_t id[LLD_MAX_FLASH_BANKS];
uint32_t id[denali->max_banks];
int i;
denali->total_used_banks = 1;
for (i = 0; i < LLD_MAX_FLASH_BANKS; i++) {
for (i = 0; i < denali->max_banks; i++) {
index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90);
index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0);
index_addr_read_data(denali,
......@@ -445,6 +445,17 @@ static void find_valid_banks(struct denali_nand_info *denali)
"denali->total_used_banks: %d\n", denali->total_used_banks);
}
/*
* Use the configuration feature register to determine the maximum number of
* banks that the hardware supports.
*/
static void detect_max_banks(struct denali_nand_info *denali)
{
uint32_t features = ioread32(denali->flash_reg + FEATURES);
denali->max_banks = 2 << (features & FEATURES__N_BANKS);
}
static void detect_partition_feature(struct denali_nand_info *denali)
{
/* For MRST platform, denali->fwblks represent the
......@@ -562,7 +573,7 @@ static void denali_irq_init(struct denali_nand_info *denali)
int_mask = DENALI_IRQ_ALL;
/* Clear all status bits */
for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
for (i = 0; i < denali->max_banks; ++i)
iowrite32(0xFFFF, denali->flash_reg + INTR_STATUS(i));
denali_irq_enable(denali, int_mask);
......@@ -579,7 +590,7 @@ static void denali_irq_enable(struct denali_nand_info *denali,
{
int i;
for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
for (i = 0; i < denali->max_banks; ++i)
iowrite32(int_mask, denali->flash_reg + INTR_EN(i));
}
......@@ -1345,6 +1356,7 @@ static void denali_hw_init(struct denali_nand_info *denali)
/* Should set value for these registers when init */
iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
iowrite32(1, denali->flash_reg + ECC_ENABLE);
detect_max_banks(denali);
denali_nand_timing_set(denali);
denali_irq_init(denali);
}
......@@ -1522,7 +1534,7 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
/* scan for NAND devices attached to the controller
* this is the first stage in a two step process to register
* with the nand subsystem */
if (nand_scan_ident(&denali->mtd, LLD_MAX_FLASH_BANKS, NULL)) {
if (nand_scan_ident(&denali->mtd, denali->max_banks, NULL)) {
ret = -ENXIO;
goto failed_req_irq;
}
......
......@@ -454,7 +454,6 @@
#define READ_WRITE_ENABLE_HIGH_COUNT 22
#define ECC_SECTOR_SIZE 512
#define LLD_MAX_FLASH_BANKS 4
#define DENALI_BUF_SIZE (NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE)
......@@ -494,6 +493,7 @@ struct denali_nand_info {
uint32_t totalblks;
uint32_t blksperchip;
uint32_t bbtskipbytes;
uint32_t max_banks;
};
#endif /*_LLD_NAND_*/
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册